tender for provision of high wall enclosure opposite to main gate entry and provision of raised platform for guard near main gate at af stn adampur.; 1 surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting outin soft/loose soil complete, all as specified & directed. 2 excavation over areas in soft/loose soil not exceeding 1.50 metre deep and getting out complete, all as specified and directed. 3 excavation over areas in soft/loose soil exceeding 1.50 metre but not exceeding 3.00 metre deep and getting out complete, all as specified and directed. 4 returning filling in including spreading, levelling, watering and well ramming in layers notexceeding 25cm thick complete, all as specified & directed. 5 removing excavated spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified & directed. 6 m&l for pcc type d-2 (1:4:8), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified & directed. 7 m&l for reinforced cement concrete, type a-1 (1:1½:3), (nominal mix) , as in in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concretecomplete all as specified. 8 m&l for reinforced cement concrete,type a-1 (1:1½:3), (nominal mix), as in beams, cantilevers, bressumers, lintels over 1.5 metre clear span and the like complete all as specified and as directed. 9 m&l for reinforced cement concrete, type a-1 (1:1½:3), (nominal mix) , as in columns, pillars, piers, posts and struts complete all as specified and directed. 10 supply only water proofing compound, isi marked, complete all as specified & directed. 11 m&l for brick work using bricks as specified in ps clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified & directed. 12 m&l for use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished surfaces of concrete, complete all as specified and as directed. 13 m&l for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished surfaces of concrete, complete all as specified and as directed. 14 m&l for use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchionswith rough finished surfaces of concrete, complete all as specified and as directed. 15 s&f plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections of grade fe 410-w (grade e-250), complete all as specified. 16 m&l for mild steel tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. 17 m&l for mild steel tmt bars 5 mm and over up to and including 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders complete all as specified. 18 m&l for rendering 15 mm thickon fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified & directed.note: wpc will be measured and paid for separately under respective item of boq. 19 m&l for prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -a) applying wall care putty, in two coats& smoothening the surfaces as specified. (preparatory to paint as directed).complete all as specified. (b) two coats of exterior acrylic emulson over and including a coat of water based exterior primer complete all as specified.