|
| 1 | Dismantling plain or corrugated steel sheeting any guage, thickness, including Nainital pattern or similar pattern roof covering complete all as specified and directed. |
| 2 | Demolition of brick work or stone masonry precast PCC block walling built in cement mortar complete all as specified and directed. |
| 3 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each.& removing to or from store all as specifed & directed. |
| 4 | Taking down cement or cement lime plaster of any description on brick or PCC blocks or stone wall or concrete surface etc including racking out joints, hacking for keys, scrubbing down with water etc all as specified and directed. |
| 5 | Dismantling of ceiling board (flbre pulp, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets complete all as specified and directed. |
| 6 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 7 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. |
| 8 | Dismantling of timber scantling 40 Sqcm and over in section in any position as in framed work complete all as specified and directed. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 10 | Dismantling of Stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar, aprons etc. |
| 11 | Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed. |
| 12 | Taking up or down 20mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed. |
| 13 | Dismantling water tanks 500 ltrs capacity complete all as specified and directed. |
| 14 | Dismantling water tanks of any description, capacity exceeding 500 litres but not exceeding1000 liters complete. |
| 15 | Dismantling wrought iron or mild steel work of any description not otherwise provided for. |
| 16 | S&F 0.63mm thick galvanised corrugated MS sheeting (CGI sheet roofing) with two corrugation side laps, with 120gm Zinc (Spelter) coating per Sqm both sides inclusive fixed with coach screws and washers as in roofs etc all as specified |
| 17 | S&F 0.63mm thick plain galvanised MS sheeting using grade-O sheets with 120gm Zinc (Spelter) coating Per Sqm both sides inclusives, as in roof, ridges, hips, valley gutters, drip and straight flashing complete all as specified and directed. |
| 18 | S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa (AZ 150) as in roof covering / cladding to wall , fixed with self tapping screw as specified and directed |
| 19 | S&F Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall , fixed with self tapping screw as specified and directed |
| 20 | M&L for brick work with sub class 'B' bricks using old size bricks straight or curved on plan exc 6 mtr mean radius, built in CM 1:6 all as specified and directed. |
| 21 | M&L for rendering 15 mm thick readymade plaster on inner/outer walls by adding 17-19% of potable water by weight of material for thickness above 15mm it is recommended to be applied in multiple layers. ready mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the compressive strength @ 28 days 10-12 Mpa/Bulk density 1500-1600 Kg/m3. (Note : The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 Mtr ht all as specified and directed) |
| 22 | M&L for preparation of New plastered surfaces & applying a layer of 3mm thickness Birla putty on wall surfaces including cornics etc for proper levelling of plaster and two coat of oil emulision distemper complete all as specified and directed. |
| 23 | M&L preparation of newlly plastered surfaces of ceiling surfaces and applying three coats of white wash complete all as specified & directed |
| 24 | Material & Labour for applying Two or more coats of 100% remium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed. |
| 25 | M&L preparation of old surfaces including cornices etc and one coat of oil bound distemper complete all as specified and directed. |
| 26 | M&L for preparation of old plastered surfaces & applying a layer of Birla putty on wall surfaces including cornics etc for proper levelling of plaster and two coat of oil emulision paint complete all as specified and directed. |
| 27 | S&F of powder coated grid frame work for false celling comprising of the following sections for making partitions of 600x600 mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 4mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 28mmx24mmx0.3mm thick , cross tee shall be 28mmx24mmx0.3mm thick and wall angle shall be 24mmx24mmx0.3 mm thick incl 4 mm thick E-Board Classic (Make-Everest) for insulation and accoustic purpose, 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surface complete all as specified and directed.complete all as specified and directed. |
| 28 | S&F solid PVC wall lining dual colour consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete fixing arrangement icluding taking down old existing wooden panelling complete. |
| 29 | S & F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 30 | M & L for PCC 1:3:6 (40 mm graded aggregate)as In surface channel & drain complete all as specified and directed. |
| 31 | Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as pecified and directed. concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.All as specified and directed. |
| 32 | M&L PCC 1:5:10 type E2 using 40mm graded aggregate as in sub base complete all as specified and directed. |
| 33 | M&L chequred tiles 300 x 300 x 25 mm coloured glossy finish rubber pressed moulded of approved pattern & shade make as approved by GE as in floor 15 mm thick set in CM(1:4) and jointed complete all as specified and directed. |
| 34 | M&L interlocking tiles 75-80 mm coloured rubber moulded glossy finish 80mm thick of approved pattern & shade ISI Marked or approved by GE set jointed over 40 mm thick fine sand cushion including sides are tappered 75 mm in width by PCC 1:3:6 type C1 (using 20mm graded crushed stone agg.) complete all as specified and directed. |
| 35 | M&L for 2nd class hard wood clean sawn as in scantling framed over 40 sqcm and fixed with screws etc all as specified and directed.. |
| 36 | S & F Second class hardwood 25 mm boarding plain one side with butt joint fixed with nails in any situation. Complete all as specified and directed. |
| 37 | S&F mild steel framed work such as purlin , truss, square tube , MS pole , grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, welded wire mesh and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed. |
| 38 | M&L 300x450x7mm thick glazed ceramic digital tiles coloured incl , design and pattern as approved fixed as in vertical surface etc, set and jointed in neat cement slurry and pointed with white cement with colour pigment to match incl rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed. |
| 39 | M&L colour non skid ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tiles exc. 0.11 sqm but n.exc. 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement with colour pigment incl 15mm thick screed bed in CM 1:6 complete all as spd |
| 40 | M&L colour non skid ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tiles exc. 0.18 sqm but n. exc. 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement with colour pigments incl 15mm thick screed bed in CM 1:6complete all as spd |
| 41 | M&L colour non skid ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tiles exc. 0.18 sqm but n. exc. 0.38 sqm in skirting /dado etc set and jointed in neat cement slurry and pointed in white cement with colour pigments incl rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.complete all as spd |
| 42 | M&L 18 to 20 mm thick granite stone on steps including rubbing and polishing and making hole for gas pipe and front portion rounded and chamfered complete including screed bedding 15 mm thick in CM 1:4 complete all as spd |
| 43 | S&F in repairs parquet flooring 8.3 mm thick hard board plank both side laminated with decorative surface and approved by GE laid above the thermoplastic sheet complete all as spd |
| 44 | M&L for 15mm bore GI tubing, medium grade, galvanised with and including all GI fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 45 | M&L for 20 mm bore GI tubing, medium grade, galvanised with and including all GI fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 46 | S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postion 500 ltrs capacity and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram of Make - Prayag complete all as specified and directed. |
| 47 | S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postion 1000 ltrs capacity and including 20mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram of Make - Prayag complete all as specified and directed. |
| 48 | S&F angle cock 15 mm bore brass chromium plated, screwed both ends for pipes or for unions fixed in repairs including making good to match with existing surface |
| 49 | S&F pillar taps 15 mm bore, brass chromium plated , screwed down high pressure with or without letter Hot or Cold with long screwed shanks and fly nut complete all as specified, fixed in repairs. |
| 50 | S&F bib tap standard of PTMT (Polytetra Methylene Terephthalate Engineering Thermoplastic Bath fitting), any colour, screwed foriron pipe 15 mm bore pipe (minimum weight 90 gm) all as specified, fixed in repairs (Make : Prayag or Equivelent as approved) |
| 51 | S&F in repair polymer white (polypropeylene Delrin and ABS) low level flushing cistern 10 Ltrs capacity, valveless, syphonic action type complete with inlet, ball valve float valve, bends brackets, rawl plug, brass screws handle etc complete, complete all as specified and directed. |
| 52 | S&F in repairs, 550x400mm vitreous China, wash hand basin , flat back with pedestal excluding trap and waste chain and plug and porcelain stopper including sutaible size brackets waste pipe and waste coupling complete all as specified and directed. |
| 53 | S&F vitreous china squatting pan Orrissa pattern size 580 x 440 mm white with intregal foot rests, with & including P or S trap (excluding material & labour of flushing cistern and flush pipe) including conection to trap and to flush pipe etc complete including making good to floor complete all as specified and directed fixed in repairs. |
| 54 | S&F in repair 15mm dia bib tap long body CP, screwed for iron pipes complete all as specified and directed |
| 55 | S&F aluminium partition powder coated of frame of aluminium section 44.45 x 44.45 x 1.6mm etc and 5 mm thick sun broken glass fixed with gasket with aluminium clip , jointing clips, glazing clips, rubber packing, screws etc.and as directed at site. Make Jindal or its equivalent approved make including taking down old userviceable wooden partition completeall as spd |
| 56 | M&L preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide. |
| 57 | S&F in repairs hydraulic door closer Aluminium ( Die cast) regulated designation No-3 universal type for door shutter complete all as spd |
| 58 | S&F 18mm thick MDF Board both side finished as in wardrobe/ cup board shutter all as specified and as directed by Engineer-in-Charge. |
| 59 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames, glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips and providing and fixing new ones all as specified |
| 60 | S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed. |
| 61 | S&F in repairs of galvanised mild steel wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. |
| 62 | S & F 20mm Dia Aluminium alloy anodised curtain rod decorative fency type with brackets complete all as specified. Please Enable Macros to View BoQ information |
