|
| 1 | Excavation over areas n exc 1.5 m in depth; for foundation, etc. and getting out in soft/loose soil complete all as specified and as directed. |
| 2 | Excavation over areas exc 1.5 m in depth but n.exc 3.00 depth for foundation, etc. and getting out in soft/loose soil complete all as specified and as directed. |
| 3 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil. Complete all as specified. |
| 4 | M & L for PCC 1:4:8 with type D2 using 40 mm graded crushed stone aggregate as in filling, foundation and mass concrete complete all as specified and directed. |
| 5 | M&L for Nominal mix RCC M-30 (using 20mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed |
| 6 | M&L for Nominal mix RCC M-30 (using 20mm graded stone aggregate) in Walls, retaining walls,basement walls, ballast walls and the like; anythickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed |
| 7 | M&L for use and waste form work to sides of concrete foundations, footings, rafts, and raft beams sides and soffit of foundations and plinth beam and similar work for flat rough finished surface complete all as specified and directed. |
| 8 | M&L for use and waste form work to faces of walls retaining walls, abutments, parapets and like for flat rough finishesd surface complete all as specified and directed. |
| 9 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 10 | M&L for 110 mm bore PVC pipes as in weep holes complete all as specified. |
| 11 | M&L for broken stone or boulders including hand packing (any thickness) at back side of weep holes and raising or lowering to the required level complete all as specified. |
| 12 | Return filling in Surplus soil, back filling of retaining wall including spreading, levelling, watering and well ramming in layers n.exc. 25cm complete all as specified. |
| 13 | Surface excavation not exceeding 30 cm deep and averaging 30 cm deep and getting out in soft/loose soil complete all as specified. |
| 14 | Back filling of surface area using approved earth obtained from excavation complete all as specified and as directed by Engineer in Charge |
| 15 | M&L Precast cement concrete block masonry type C1 1:3:6 (20mm graded agg) with solid block exc 10cm in width and setting in CM 1:6 complete all as specified and directed. |
| 16 | M & L for rendering 5 mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 (Total 15 mm thick) on concrete or brick masonry surfaces and finishing the top surface even and fair without using extra cement complete all as specified and as directed. |
| 17 | M & L preparation of newly surfaces of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. Make : Asian Paints (Apex Ultima), Berger (Weathercoat Long Life Flexo), Nerolac (Excel Total), Shalimar Paints (Weatherpro+ Super Luxury Emulsion). Note : Rate inclusive of scaffolding at any height. |
| 18 | M & L for providing cement concrete with type B1 (20 mm graded stone aggregate ) as in drain/coping complete all as specifed and directed. |
| 19 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified. |
| 20 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting pointcomplete all as specified and directed. |
| 21 | M & L RCC M-30 (design mix) as in columns, pillars, piers, posts and struts complete all as specified and as directed. |
| 22 | M & L RCC M-30 (design mix) as in beams, tie beam, gable beam cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. |
| 23 | Providing precast reinforced ce- ment concrete with tyhpe B1 1:2: 4 (20 mm graded aggregate) in win- dow or door opening, lintels band bressumers, steps, quoin blocks (for use with masonry), string courses, set in cement mortar 1:4 complete all as specified and as directed. |
| 24 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished surface flat complete all as specified and as directed. |
| 25 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions with square or rectangular rough finished surface complete all as specified and as directed. |
| 26 | Formwork to sides and soffits of floor or roof beams, tie beam, gable beam, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. |
| 27 | M & L for MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed. |
| 28 | M&L TMT bars 5 to 8 mm mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia as in stirrups complete all as specified and directed. |
| 29 | M&L for rendering 10mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even smooth without using extra cement all as specified. |
| 30 | M&L for rendering 15mm thick cement plaster on fair faces of concrete block masnory in two layers, base layer 10mm thick in CM (1:6) and top layer 5mm thick in CM 1:4(with river sand) mixed with WPC as per manufacture' s instructions, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be measured and paid seperately |
| 31 | Supply only Liquid water proofing compound. |
| 32 | M&L preparing newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of primer complete all as specified & directed. |
| 33 | S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed |
| 34 | S & F Anodised aluminium window and ventilator shutters, side hung type with or without sash bars, aluminium sections weighing 0.55 kg/m and thickness of section not less than 1.6 mm including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle 150 mm long (1 no.) complete all as specified and as directed |
| 35 | Supply only Sheet glass, 4.8 mm ordinary quality and glazing with oil putty in square in n.exc 0.5 sq.m in each pane complete all as specified and as directed |
| 36 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 37 | Providing and fixing Factory made single rebate WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete in colour as per direction of Engineer-in-Charge.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account. |
| 38 | Providing and fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 39 | M&L for sand filling under floors, cushning under interlocking tiles or in foundations incl watering and consolidations complete all as specified and directed. |
| 40 | M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete as specified as directed. |
| 41 | M&L for PCC 1:4:8 type D-2, 100 mm thick using (40mm graded) as sub base Complete all as specified. |
| 42 | M&L for joint free non skid ceramic tiles (coloured ) 7 to 8 mm thick , area of each tile exceeding 0.18 sqm but not exc 0.38 sqm as in floors, stet and jointed in neat cement slurry and pointed in shete or coloured cement to match the shade of tiles over & incl 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed. |
| 43 | M&L for joint free non skid ceramic tiles (coloured ) 7 to 8 mm thick , area of each tile exceeding 0.18 sqm but not exc 0.38 sqm as in skirting, stet and jointed in neat cement slurry and pointed in shete or coloured cement to match the shade of tiles over & incl 10mm thick rendering in cement & sand mortar 1:4 complete all as specified and as directed. |
| 44 | M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed. |
| 45 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed. |
| 46 | M & L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed. |
| 47 | S&F 200mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed. |
| 48 | S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 49 | S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. |
| 50 | S&F Stainless steel Butt hinges, medium weight, cold rolled mild steel, and fixed complete as specirfied and directed. |
| 51 | M&L for 75mm thick plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate finished even and smooth without using extra cement as in plinth proteaction complete all as specified and directed. |
| 52 | Preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 53 | Material and Labour Point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core, unsheathed, copper conductor cables drawn through and including PVC conduits Concealed in walls, ceiling etc with all fittings and accessories of PVC conduits (like Tee, bend etc.) complete fixed to walls/ceiling etc. with and including 1.5 Sqmm (nominal area) FRLSH PVC insulated, unsheathed, multistranded, single core, copper cable green in colour as in earth continuity wire connecting to common earth point and 1.6 mm thick mild steel sunken terminal boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point/ 3 pin 5 Amps socket outlet independent point controlled by one, one way switches complete including cutting, chasing the surface and then making good the same in CM 1:3 complete all as specified and directed by the Engr-in-Charge.(a) One light/Fan/Exhaust Fan/Wall fan point controlled by one switch |
| 54 | (b) One 3 Pin Socket outlet 5 Amp on independent board |
| 55 | (c) One 3 pin Socket outlet on same board. |
| 56 | - Ditto - All as per item No. 53.00 here-in-before but using 2.5 Sqmm size stranded copper conductor cable for one 16 Amp switch socket outlet point on independent board complete PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified and directed by Engineer-in-Charge. |
| 57 | Supply & fix Modular type switch 6 Amps 230V AC single module one way complete all as specified and as directed. |
| 58 | Supply & fix Modular socket 6 Amps- 2/3 pin combined, 230V AC 50 Hz, 2 module as per existing make and model complete all as specified and as directed. |
| 59 | Supply & fix Modular socket 16 Amps 2/3 Pin combined, 230V, 50Hz 2 module as per existing make and model complete all as specified and as directed. |
| 60 | Supply & fix Modular switch 6 Amps 230V AC single module one way complete all as specified and as directed. |
| 61 | S& F Modular Bell push 6A 1 Module complete all as specified and directed. |
| 62 | S&F ceiling rose, surface bakelitet type, 240V, three terminals complete all as specified and directed. |
| 63 | M&L Sub Main wiring with two single core FRLSH PVC insulated unsheathed cable 1100 Volts grade, 6 Sqmm size with multistranded copper conductor, drawn in non metallic rigid PVC conduit of size 25 mm dia ISI Marked including PVC insulated unsheathed 6 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dully completed. |
| 64 | Taking down existing u/s fitting any type any size and Supply and fixing in replacemnt of LED lights fitting 1x20 w, 220V AC decorative box type with driver, holder including LED tybe light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed |
| 65 | S&F in replacement MCB, DB TPN 415 Volts 200amps rated Busbar, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 with MCB as incommer and MCB SP/TP in outgoing complete all as specified and directed by Engineer-in-charge Make Legrand/Seimens/L&T/Schenider |
| 66 | S&F in replacement MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden recangle board of first quality of suitable size for mounting of DB Box complete all as specified and directed by Engineer-in-charge Make Legrand/Seimens/L&T/Schenider |
| 67 | Supply and fixing 415V, 63Amps 10 KA 'C' curve miniature circuit breaker (MCB) of following poles and current carring capacity in the DB Complete with connection testing and commissioning complete all as directed. |
| 68 | Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity of 6Amp to 32 AMP, in the SPN DB Complete with connection testing and commissioning complete all as directed. |
| 69 | Supply & fix of DP RCBO 30mA 40Amp SPN complete all as specified and directed by Engineer-in-charge |
| 70 | Supply and fixing in 1x9w/1x10w bnulkhead luminaires including LED Light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as directed. |
| 71 | Supply & Fix Exhaust fan, 300 mm Sweep 240 volt , complete with louvers including all civil work like cutting and making circular opening in existing wall etc, including connecting up with twin core twisted flexible copper conductor cable with suitable size . Make :- Bajaj/usha/CG |
| 72 | Materials and labour for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level,earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using GI earth strip 25x4 mm connected bu means of bolts, nuts, check nuts and washers of GI or steel, GI strip proected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 cm c/c bothways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed. |
| 73 | Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable Heavy duty under ground cable, with standard aluminium conductor, 1100 Volt grade of size 25x3.5 sqmm, laid in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as directed by the Engr-in-Charge. |
| 74 | Supply & laying in replacement Telerex DWC (Double Wall Corrugated) HDPE pipe ISI marked of outer dia of 40 mm and inner dia 32 mm polyethylene including couplers, bends, cap etc., with smooth internal and profiled external surface for non pressure under ground cable complete all as specified and directed |
| 75 | Supply and laying 50mm bore of GI pipe light grade with all fittings in trenches for road cutting |
| 76 | Supply and laying GI pipe medium grade with all fittings in trenches :- 20mm bore of GI pipe |
| 77 | 50mm bore of GI pipe |
| 78 | Taking out UNSV Gun Metal globe & S&F Gun Metal globe or gate valves, conf to IS 778 with iron wheel head, screwed both ends for iron pipe and fixed in existing or new position for following size:-20mm bore of GI pipe |
| 79 | 50mm bore of GI pipe Please Enable Macros to View BoQ information |
