|
| 1 | Civil work |
| 2 | 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) |
| 3 | Cement concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of stpes etc. complete. 25 mm thick with 20 mm nominal size stone aggegate. |
| 4 | Providing, hcisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but,excluding cost of reinforcement, with 1:1.5:3 (1 cement 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone ggregate 20 mm nominal size derived from naturalsources). |
| 5 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 6 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 7 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awallthickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at cornersand joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, thevertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19gauge, EPDM rubber gasket weather seal to be provided through out the frame. The doorframe to be fixed to the wall using M.S. screws of 65/100 mm size, complete as permanufacturer’s specification and direction of Engineer- in-Charge. |
| 8 | Providing and fixing factory made panel PVC door shutter consisting of frame made outof M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mmfor top & bottom rails. M.S. frame shall have a coat of steel primers of approved make andmanufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall betapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVCsheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on theinner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mmshall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom andlock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm widecross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mmthick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & railswith 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, andjoined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesiveetc. complete as per direction of Engineer-in-charge, manufacturer's specification &drawing. 30 mm thick plain PVC door shutters |
| 9 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content lessthan 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats) |
| 10 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work |
| 11 | Dismantling doors, windows and clerestory windows (steel or wood) shutter includingchowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 12 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm |
| 13 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 14 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means infoundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), includingdressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out theexcavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 15 | B/W in cm 1:6 FP |
| 16 | B/W in cm 1:6 SS |
| 17 | Brick work with flyash FPS non modular brick of class designation 7.5 in superstrucutre in CM 1:6 |
| 18 | Fixing standard steel glazed doors, windows and ventilators in walls, including fixing offloat glass panes with glazing clips and special metal-sash putty of approved make, ormetal beading with screws, (only steel windows, glass panes cut to size and glazing clipsor metal beading with screws, shall be supplied by department free of cost. |
| 19 | Fencing with angle iron post placed at required distance embedded in cement concreteblocks, every 15th post, last but one end post and corner post shall be strutted on bothsides and end post on one side only and provided with horizontal lines and two diagonalsinterwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum),between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Costof posts, struts, earth work and concrete work to be paid for separately). Payment to bemade per metre cost of total length of barbed wire used. With G.I. barbed wire |
| 20 | Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 21 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto 12 metre or as desired byEngineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size(5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curvedsurfaces, excluding the cost of purlins, rafters and trusses and including cutting to size andshape wherever required. |
| 22 | Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mmthick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymercoated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with selfdrilling fastener and EPDM washers etc. complete (excluding the cost of purlins, raftersand trusses), including cutting sheets to size and shape wherever required. |
| 23 | Extra for circular cutting in reinforced by organic fibres and/or inorganic synthetic fibrescement corrugated/ semi corrugated 6 mm thick sheet roofing for making openings of areaexceeding 40 square decimeter.metre 169.8 Extra for providing and fixing wind ties of 40x 6 mm flat iron section. |
| 24 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirmingto IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability forhot & cold water supply, including all PP - R plain & brass threaded polypropylenerandom fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing ofjoints complete as per direction of Engineer-in-Charge. Internal Exposed on walls PN - 16 Pipe, 25mm OD (SDR-7.4) metre 254.15 |
| 25 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore |
| 26 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia |
| 27 | Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms |
| 28 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
