|
| 1 | Supply & installation of Salon Slats surco made of pinewood EI grade fiberboard melamine/veneer laminated finish, groove perforated slats L8-2 -(2mm grooves @8 mm centers with 52% open area) / L16-2 - (2mm grooves @16 mm pitch with 27% open area)/ L32-2- (2mm grooves @32 mm centers with 15% open area)/L64-2-2 (2mm grooves @ 64mm centers with 8% open area), backlined with soundtexblack acoustical fleece of 0.27 mm thick surface density 63g/m2, tounge-groove edge for a seamless look, 5-test fire retardant grade, size 128x2440x16mm, volume density of base board 700Kg/m3, weight is 9Kg/m2 (L16), 10.5Kg/m2 (L32), 11Kg/m2 (L64) installed by useing Strut framework system. The Strut framework system shall include Strut CC25, fully knurled, sectiional thickness 0.55mm, length 3600mm web 50mm depth of 25mm and equal flanges 15mm is fastened to the wall positioned vertically at every 600mm centers. Strut CC 18 , Aluminium corc cross channel, thickness 0.5mm length 2400mm web 15mm & 27 mm, depth 18 mm and flanges of 7mm with suitable edge and centre brackets is then fixed perpendicular to the Strut CC25 with the help of fasteners at every 400mm centers. Slats Surco Plus of size 128x2440x16 mm in then fixed perpendicular to Strut CC 18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Note Wooden packing of appropriate thicknes to be provided at rear of strut to bring finish inline with Stretch NRC finish. The work will include required scaffolding upto all height, wire chicken mess etc complete |
| 2 | P/f of the tables of 600mm wide counter table top of 19mm block board of make green ply, duro, century, complete with 1mm thick laminated on top & bottom. The table top to be at a height of 750mm from the floor with suitable no. of vertical support of sixe 600X750mm. The top of table & modesty panels including the sides to have imm laminate surface with edge beading as required to complete finsih and design drawings. The table to have drawer units of size 600X750mm as per drawings. The inner side of table and drawer units to be given spirit polish in black colour after making base complete including hardware and accessories as required.Including cost of adhesives as required. The table to have cut outs & cable manager for any kind of mike, network, electrical fixtures etc as per design & drawings. The work shall be executed as per the drawings, specifications & instructions of engineer in Charge .(Table top plan area to be measured for payment). |
| 3 | Providing and Fixing Cushion Vinyl/Fully flexible Vinyl Flooring confirming toI.S.-3462 Flooring of approved make with fibre base using rubber base adhesives including rolling with light wooden roller complete : |
| 4 | 1.0 mm thick. |
| 5 | Supplying and fixing Rollor Blinds of good quality and approved make made out of Imported fabric including Roller Mechanism and lock with chain system with all necessary hooks etc. complete as per direction and sample approved by engineer-in-charge. |
| 6 | Providing and placing of High back Bifma Level 2 Certified Chair. The seat assembly is made up of injection moulded Plastic outer & inner. Plastic inner is upholustered with Pure leather and moulded HIGH Resilience (HR) Polyurethane foam of Density 45+/-2 kg/m0 and hardness load 16 + 2 kgf as per IS:7888 for 25% compression. * SEAT SIZE:47.6 cm. (W) x 49.2 cm. (D) The back asembly is made of PU Foam with insitu moulded MS E.R.W. Round Tube of size 1.9+/- 0.03cm x 0.16+/- 0.0128cm. It upholustered with Pure Leather. BACK SIZE :47.5 cm. (W) x 77.0cm. (H). The armrest top is moulded from polyurethane (PU) and mounted on to a drop lift adjustale type tupular armrest support made of 3.81+/- 0.03cm x 0.2+/- 0.l cm thk M.S. E.R.W. tube having chrome plated finish. The Armrest Height adjustable up to 6.5+/-0.5cm in 5 step.The adjustable tilting mechanism is designed with the following features:• 360° revolving type. •Front-pivot for tilt with feet resting on ground and continuous lumber support ensuring more comfort. •Tilt tension adjustment can be oprated in seating position. • 5-position tilt limiter giving option of variable tilt angle to the chair. • Seat/ back tilting ratio of 1:2. • The mechanism housing is made up of HPDC Aluminium black powder coated. The Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0+/-0.5cm. Back frame is connected to the Up/ Dn mechanism housed in plastic T spine. It can be adjust in the range of 7.42+/- 0.5cm for the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0 +0.3cm. The pedestal is High Presure Dia cast polished Aluminium and fitted with 5 nos. twin wheel caster. The Pedestal is 65.0+/- 0.5cm pitch-center dia (75.0+/- 1.0cm with caster.) The 5 Nos. twin wheel caster are injection moulded in plastic having 6.0+/- 0.lcm wheel Diameter and assembled to pedestal. OEM Shall be mamber of IGBC and shall have ISO 9001: 2015, ISO 14001:2015, ISO 45000: 2015 and ISO 50001:2018 Certification. All ISO certificates should be issued b NABCB authorised agency. |
| 7 | Providing and placing of Mid-Back Bifma Level 2 Certified Chair. The seat assembly is made up of injection moulded Plastic outer & inner. Plastic inner is upholustered with Pure leather and moulded HIGH Resilience (HR) Polyurethane foam of Density 45+/-2 kg/m0 and hardness load 16 + 2 kgf as per IS:7888 for 25% compression. * SEAT SIZE:47.6 cm. (W) x 49.2 cm. (D) The back asembly is made of PU Foam with insitu moulded MS E.R.W. Round Tube of size 1.9+/- 0.03cm x 0.16+/- 0.0128cm. It upholustered with Pure Leather. BACK SIZE :47.5 cm. (W) x 77.0cm. (H). The armrest top is moulded from polyurethane (PU) and mounted on to a drop lift adjustale type tupular armrest support made of 3.81+/- 0.03cm x 0.2+/- 0.l cm thk M.S. E.R.W. tube having chrome plated finish. The Armrest Height adjustable up to 6.5+/-0.5cm in 5 step.The adjustable tilting mechanism is designed with the following features:• 360° revolving type. •Front-pivot for tilt with feet resting on ground and continuous lumber support ensuring more comfort. •Tilt tension adjustment can be oprated in seating position. • 5-position tilt limiter giving option of variable tilt angle to the chair. • Seat/ back tilting ratio of 1:2. • The mechanism housing is made up of HPDC Aluminium black powder coated. The Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0+/-0.5cm. Back frame is connected to the Up/ Dn mechanism housed in plastic T spine. It can be adjust in the range of 7.42+/- 0.5cm for the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0 +0.3cm. The pedestal is High Presure Dia cast polished Aluminium and fitted with 5 nos. twin wheel caster. The Pedestal is 65.0+/- 0.5cm pitch-center dia (75.0+/- 1.0cm with caster.) The 5 Nos. twin wheel caster are injection moulded in plastic having 6.0+/- 0.lcm wheel Diameter and assembled to pedestal. OEM Shall be mamber of IGBC and shall have ISO 9001: 2015, ISO 14001:2015, ISO 45000: 2015 and ISO 50001:2018 Certification. All ISO certificates should be issued b NABCB authorised agency. |
| 8 | Providing and placing of the revolving chair. The Seat assembly is made up of 1.2 +-0. 1cm. thick hotpressed plywood measured as per QA method described in OCP-QLTA-P14-18, upholstered with fabric upholstery covers and moulded Polyurethane foam. • SEAT SIZE 48.0 cm. (W) x 47.0 cm. (D) The back asembly is made of powder coated (DFT 40-60 microns) tubular frame of dia 1.9 +- 0.02cm. x 0.2 + 0.016cm.thk. BACK SIZE 47 cm. (W) x 58cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =45+/-2 kg/m0 and hardness load 16 +/- 2 kgf as per IS:7888 for 25% compression. The armrests top are injection moulded from black Co-polymer Polypropylene.The perforated back cover is provided with in injection moulded ABS label holder and paper label, The seat is covered on underside with black polyproppylene non-woven fabric. The permanent contact mechanism is designed with the 360 revolving type, 14 +/-2 back-tilt only, upright position locking, tilt tention adjustment.OEM Shall be mamber of IGBC and shall have ISO 9001:2015, ISO 14001:2015, ISO 45000: 2015 and ISO 50001:2018 Certification. All ISO certificates should be issued by NABCB authorised agency. |
| 9 | Providing and placing of Green Pro Certified chair. The Seat assembly is made up of 1.2 +0. 1cm. thick hotpressed plywood measured as per QA method described in OCP-QLTA-P14-18, upholstered with fabric upholstery covers and moulded Polyurethane foam. • SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) The back asembly is made of powder coated (DFT 40-60 microns) tubular frame of B 2.54 +0.03cm. x 0.2 + 0.016cm.thk MS ERW tube designed with contoured lumbar support for extra comfort. The back is upholstered using Net fabric with high tenacity yarn. BACK SIZE 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =45+/-2 kg/m0 and hardness load 16 + 2 kgf as per IS:7888 for 25% compression. The one-piece armrests are injection moulded from black Co-polymer Polypropylene.The powder coated (DFT 40-60 microns) tubular frame is cantilever type & made of B 2.54 +0.03cm. x 0.2 +0.016cm.thk M.S.ER.W. Tube.OEM Shall be mamber of IGBC and shall have ISO 9001:2015, ISO 14001:2015, ISO 45000: 2015 and ISO 50001:2018 Certification. All ISO certificates should be issued by NABCB authorised agency. |
| 10 | S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including making jhiri in the wall,clamps at suitable spacing, covering conduit and making good the same as required. |
| 11 | 25 mm |
| 12 | Supplying and laying FR PVC insulated & unsheathed flexible copper conductor of following nominal sizes with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. |
| 13 | 2 x 1.5 sq.mm |
| 14 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 15 | P&F 240/415 V AC Change Over Miniature circuit breaker with three positions (I-O-II) which allows supply change over from one source to second source & vice- versa, conforming to IS/ IEC 60947-3 in existing board/sheets including making connections, testing etc. as required. |
| 16 | Double Pole |
| 17 | 25 Amp, 2 Module |
| 18 | SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and Other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:- |
| 19 | (a) Thickness of CRCA sheet shall not be less than 1.6 mm upto 450 mm length/ width of any compartment and be 2.0 mm above 450 mm, load bearing structure shall be 2.0 mm thick sheet supported by base M.S. channel if required, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. Removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided |
| 20 | (b) complete panel shall undergo a process of degreasing, Water rinsing, Activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then Powder coated with approved shade of minimum 70 microns on both side(Inner & Outer side) of panel. The panel having PE foam/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire. |
| 21 | [c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 Sq.mm, Earth wire with 2.5 Sq.mm and CT with 2.5 sq.mm flexible copper wire only. All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. ( Cost of Bus bar / Flexible wire for Interconnection between Main busbar and Switchgear is to be Paid Extra ) |
| 22 | (d) Wiring between components within switchgear and Incoming / outgoing cable shall be done through the terminal block only. Direct connection shall not be permitted. Each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. For tap-offs, adjacent terminals with shorting strips shall be used. 10% Spare terminal blocks shall be provided. Wire identification on marking strip shall correspond to the designation of the wiring diagrams. All wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. |
| 23 | (e) All wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, Wiring between terminals of various devices shall be ‘point to point’ (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. |
| 24 | (f) Floor mounted panel shall be mounted on Base frame of ISMC channel size 100 x 50 x 5 mm ( to be paid Extra ) |
| 25 | (g) Tests: The insulation resistance (with 1000 V Megger) and High voltage Power frequency test (by applying a voltage of 2.5KV for one minute) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. The insulation resistance shall not be less than three megaohm. CT Secondary current injection test shall also be carried out. |
| 26 | (h) only outer surface area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator only (CPRI type Test certificates for Temp. rise test, Short circuit test for 50 kA and IP test is to be submitted) |
| 27 | SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation from 50 to 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle ( to be paid extra) , including making connections etc. as required. OEM shall have submit NABL / CPRI / ERDA/ Intertek accrediated lab type test certificate. |
| 28 | 4 pole MCCB With Thermal Magnetic release |
| 29 | up to 100 Amp , 10 kA, fixed O/L & fixed S/C setting |
| 30 | Providing & Laying XLPE insulated & P.V.C. sheathed Armoured Aluminium cable confirming to IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing commissioning etc. as required of following size. |
| 31 | 70.0 Sq. mm |
| 32 | 3.5 core |
| 33 | Providing & Laying XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing commissioning etc. as required of following size. |
| 34 | 6.0 Sq. mm |
| 35 | 3 core |
| 36 | Supply and fixing following size of Pre Galvanized (275 GSM) floor raceways / Under floor trunking with/ without partion, including common cover, joint sleeve, cross over junction Box etc. as required. |
| 37 | 100 mm x 38 mm x 1.5 mm |
| 38 | Supply , Installation, Testing and Commissioning of Inverter type Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), R-32/R410A Green Refrigerant, wireless Remote, inbuilt drain pump, suitable for 400/230V, +/- 10% 50 Hz ,1 /3 phase AC supply, capable of performing cooling, dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll /rotary/twin rotary compressor etc. complete as required. |
| 39 | Cooling Capacity 10500-11000 Watt ISEER not less then 3.5 |
| 40 | Supply, installation, testing and commissioning of interconnecting copper refrigerant piping of DHE Grade C12200- ASTM B68, B75, chemical composition of copper %- 99.0 Min and Phosphorus %- 0.015 to 0.040 . For Annealed copper tube :- Tensile strength = 210 Mpa wih elongation % = 40 Min . Ink Mark Brand Printing on Hard Tubes should be present. duly insulated with tubular elastomeric nitrile rubber FM/UL approved with high water vapor diffusion resistance and low thermal conductivity should be certified 'Class O' in Fire Propagation as per BS 476 Part 6 with 7 mil Glass Cloth and 3 coats of anti UV paint (on area which is exposed to weather) including chase cutting andfilling with mortar, Slotted channel supports mounted on 10 mm threaded rod at suitable spacing the exposed piping shall be wrapped with glass woven cloth and lag coating for vapour barrier and weather protection. Joints shall be covered with nitrile rubber tape of 3 mm thick complete as required of following sizes. |
| 41 | 15.9 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) |
| 42 | 9.5 mm O.D., wall thinkness ≥ 0.8mm (insulation – 13 mm thick) |
| 43 | Gas charging of VRF/VRV system with R410A refrigerant gas. Before gas charging system shall be flushed with high purity Nitrogen Gas to remove carbon content, dirt particles to make sure that there is no chance of mixing any impurity with Refrigerant Gas. Thereafter System shall be tested with Nitrogen Gas at 1.5 Times of working pressure of R410 Refrigerant Gas to ensure leakproof system. Whole system shall be Vacuumed up to 500-micron level which ensures the zero-moisture content level in piping to ensure better cooling efficiency and long life of the system. |
| 44 | Supplying and drawing flexible / stranded bare copper conductor, PVC / XLPE insulated, overall aluminium mylar tape shielded ATC drain wire and outer PVC sheathed industrial Instrumentation (shielded)cables voltage grade 300/500 V as per BS /EN 50288-7 in existing surface or recessed PVC/ MS conduit/casing capping / Cable tray / Open Duct making connections, testing etc. as required. OEM must ensure that the cable is tested for complaince, either through their in house laboratory accrediated by NABL or by any Govt. laboratory accrediated by NABL and the laboratory's scope of accrediation should cover the requirements and testing procedure as per IS:10810. |
| 45 | Un Armoured |
| 46 | 4 core x 2.5 Sq.mm |
| 47 | Providing & Fixing of IS : 4985 - 2000 Class -4 (10 Kgf / Sqcm) UPVC drain water piping with fittings (IS:7834 & 10Kgf/sqcm) like elbow, socket, Tee, solvent cement jointing, support with MS hanger on ceiling or recessed in wall with chasing & plastering with 6 mm thick closed cell elastomeric nitrile rubber insulation including leakage testing etc. as required of following Nominal sizes. |
| 48 | 25 mm |
| 49 | 32 mm |
| 50 | Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia |
| 51 | 100 mm dia per running inch length |
| 52 | Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 53 | SITC of following capacity BIS certified 1Phase Input, 1Phase Output advance DSP controlled IGBT based rectifier Online UPS with Inbuilt Isolation Transformer having 0.99 Input power factor & 0.8 Output factor, Input voltage & frequency range of 180-300V on full load/ 110-300V on 50% load & 50 Hz +/- 5% and output voltage & frequency of 230V+/-1% & 50 +/- 0.1 Hz. Overall efficiency of upto 92% (without Transformer Loss), Overloading of 105 - 110% 30 mins, 111 - 130% 5 mins,131 - 150% 10 sec, THDv of < 3% for Linear & < 5% for Non linear load.UPS should have LED Panel with LCD display showing load level, Battery Voltage Level, Input & Output Voltage, Input & Output Frequency. UPS should have protection from Input High / Low;Over Load;Short Circuit; Over Temperature and give audible alarms on Battery Mode;Low Battery;Fault;Over Load & Bypass Mode. SMF Batteries of 12V VRLA for 30 mins with MS Rack and necessary cable for UPS to Batteries Installation. UPS should have valid Certification like Type III environmental declarations from third party renowned agency complying to ISO 14025, CE, ROHS,BIS,EN 62040-1, EN 62040-2, IEC 62040-3 Etc. as required. |
| 54 | 5KVA UPS with 4992 VAH Battery |
| 55 | supply, Installation, Testing & Commissioning of Delegate mike Unit with fixed microphone and flexible stem prority button for Deligate mike microphone ,optioal chime tone facility for proceeding Delegate mike announcement with two headphone socket built in loudspeaker is automatcally muted when the microphone is on/off button Delegate mike unit should have a frequency responce 400hz to10hz ,length of microphone from base to steam should not be less than 488 mm in size ;nominal acoustic input 85 db SPL,dimensions (without microphone) (HxWxD) 50x135x135 mm; weight of unit should not be less then 1.2 kg ;operating temperature -5°C to +45°C,two 3.5mm (0.14 in) stereo headphone sockets; including make connecion testing etc complete as required. |
| 56 | Supply and laying speaker cable of following size 2 core twin twisted multi stranded electrolytic grade copper conductor, overall PVC insulated and armoured cable (Blue colour) on surface/ above false ceiling including cost of GI spacers, saddles etc. as required. - 1.5 Sq.mm |
| 57 | SITC of following diagonal size professional Display, 4k Resolution, Brightness(Typ.) 440 nit and above , Contrast Ratio-2000:1 and above, Viewing Angle(H/V)-178/178, Response Time(G-to-G) 8ms, Input: RGB- Analog D-SUB, Video- HDMI 2.0 (2), HDCP- HDCP 2.2, Audio- Stereo mini Jack, USB- Only F/W upgrade, Outputs: RGB- DP1.2(Loop- out), Audio- Stereo mini Jack, External Control- RS232C(in/out), RJ45, External Sensor Detachable type(IR Ambient). Operation Hour 24/7. mounting bracket etc. as required. - 55\\" |
| 58 | SITC of following diagonal size professional Display, 4k Resolution, Brightness(Typ.) 440 nit and above , Contrast Ratio-2000:1 and above, Viewing Angle(H/V)-178/178, Response Time(G-to-G) 8ms, Input: RGB- Analog D-SUB, Video- HDMI 2.0 (2), HDCP- HDCP 2.2, Audio- Stereo mini Jack, USB- Only F/W upgrade, Outputs: RGB- DP1.2(Loop- out), Audio- Stereo mini Jack, External Control- RS232C(in/out), RJ45, External Sensor Detachable type(IR Ambient). Operation Hour 24/7. mounting bracket etc. as required. - 43\\" |
| 59 | Supply, Installation, Testing & Commissioning of Extension cables and connectors forcontribution units (Default Come with 10 Mtrs) |
| 60 | Supply, Installation, Testing & Commissioning of Connectors & Cable Clamps of OEM MakeOnly |
| 61 | Supply, installation, testing and commissioning of Cable cubby easily installed in a table 4 Inputs - 15−pin HD, 3.5mm, RJ−45, HDMI. Power Input - International and European 220V AC power sockets available.Cover - Pneumatic pop−up lid. Cutout Size (Mount Dimension) - 111 to 114mm diameter.pproved makes: Kramer, Extron, Bestnet, Crestron or equivalent. |
| 62 | Supply, Installation, Testing & Commissioning of 2X1:4 HDMI Switchable distribution Amplifier, Min total data rate: 6.75 Gbps or higher, HDTV compatible, HDCP compliant, supports EDID pass-through; support EDID Handling; control options; IR remote & RS-232;Approved makes: Kramer, Extron, Milestonepro, Crestron or equivalent. |
| 63 | Supply, installation, testing and commissioning of 15 Mtr HDMI Cable. Make: Kramer/ KeyDigital/ AMX/Manhattan or equivalent. Please Enable Macros to View BoQ information |
