|
| 1 | Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard /dense soil |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out Hard/dense soil. |
| 3 | M&L PCC 1:4:8 type D2(using 40mm graded aggregate) as in foundation filling and mass concrete etc. |
| 4 | Returning/filling in including spreading, levelling, watering and well ramming in layers n exc 25 cm in hard/dense soil. |
| 5 | Removing excavated material n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point. |
| 6 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. |
| 7 | M&L for precast cement concrete solid building blocks (1:3:6), type C-1, 10 cm thick (with plain or interlocking joints as directed) setting in cement mortar (1:4), complete, laying inner side of wall. |
| 8 | M&L for re-inforced cement concrete (nominal mix) 1:2:4 type B-1 (20mm graded aggregate) as in foundations,including rafts,plinth beams,bases for columns,etc;basement slabs,under-reamed piles and mass concrete. |
| 9 | M&L for re-inforced cement concrete (nominal mix) 1:2:4 type B-1 (20mm graded aggregate) as in columns ,pillars,piers,posts and struts complete. |
| 10 | M&L for re-inforced cement concrete (nominal mix) 1:2:4 type B-1 (20mm graded aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete. |
| 11 | M & L for RCC (1:2:4) Type B-1 (using 20mm graded aggr) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves. |
| 12 | M&L for MS TMT bars 10mm dia and over, cut to lenth, bend to shape required, including cranking, bending, sprially for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. |
| 13 | M&L for MS TMT bars 05mm dia and over, upto and including 10 mm dia in stirrups, spaces and binders. |
| 14 | U & W of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete. |
| 15 | Use & waste of form work to sides of pillars, posts, struts,piers, columns and stanchios rough finished square, rectangular or polygonal surfaces of concrete. |
| 16 | Use & waste of form work to side and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilivers, shelves including supports, overhangs etc, also splays betweennfloors and beams etc, rough finished flat surfaces of concrete. |
| 17 | M&L for hard core of gauge n.exc 63mm (broken stone and boulders), deposited, spread and levelled in layers nexc 15 cm thick, watered and rammed to a true surface. |
| 18 | M&L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as cement concrete in Sub-base floors, sub-bases floors and pavings etc complete all as specified. |
| 19 | M&L for 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floor finishes. |
| 20 | M&L for 15 mm thick screed bed in CM 1:6 for laying floor tiles . |
| 21 | M & L for Non-skid ceramic coloured tiles 7 to 8 mm thick ( square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match. |
| 22 | M & L for 350 x 250 x 7 mm/450 x 350 x 7 mm thick glazed coloured ceramic tiles on vertical surface of wall set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. (Make; Kajaria/ Orient/ Bell/ Johnson/ Somany). |
| 23 | M&L for 15 mm thick rendering in CM (1:4) mixed with liquid WPC 0.4% by the weight of cement over brick/concrete wall surfaces finished fair and even.Note : Liquid WPC shall be measured separately. |
| 24 | Suppiled only liquid WPC |
| 25 | M&L for 10mm thick rendering in CM (1:6) over block/concrete wall surfaces finished even and smooth without using extra cement. |
| 26 | M & L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finshed rough to receive tiles . |
| 27 | M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint complete all as specified and directed. |
| 28 | M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound destemper, over a coat of primer complete all as specified and directed. |
| 29 | M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, (40mm graded stone aggregate)as in plinth protection, finishing the top surfaces even and smooth W/O using extra cement. |
| 30 | S&F Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour havimg testile strenght of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified and directed. |
| 31 | S&F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour havimg testile strenght of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified and directed. |
| 32 | S & F Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified & directed.Fe-290 (Gde E-165). |
| 33 | M & L for second class hard wood Plain fillets cross sectional area n exc 3 sq cm square, rectangular or triangular in section, clean sawn, secured with nails or brads. |
| 34 | S & F Cover fillets of tempered hard board 6 mm thick, 40mm wide and fixing with screws. |
| 35 | S& F Plywood 4mm thick (No of ply 03 nos), grade BWR, type BB, fixed with screws to timber frame work as ceiling. |
| 36 | M & L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. |
| 37 | M & L for preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified. |
| 38 | S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing. |
| 39 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing. |
| 40 | S & F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete. |
| 41 | S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded. |
| 42 | S & F Sheet glass 4.0 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane. |
| 43 | S&F 100mm size stainless steel butt hinges, medium weight, cold rolled complete with stainless steel screw etc. all as specified as directed. |
| 44 | S& F Aluminium anodised barrel tower bolts 150mm long of extruded section and fixed |
| 45 | S&F 250mm long aluminium anodized sliding door bolt with hasp and staple (bolt type and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy complete. |
| 46 | S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised. |
| 47 | S & F 20mm 3-layer PP-R P o l y p r o p y l e n e random copolymer concealed pipes SDR 7.4 PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold watersupply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc |
| 48 | S&F 15mm dia Bib tap chromium plated screwed down , screwed for iron pipe complete |
| 49 | S & F 15mm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed |
| 50 | S&F Towel Rail 450mm long of CP fixed with and including Chromium plated brass screws and wooden/plastic cleats . |
| 51 | S& F PVC connections 15 mm size, 450 mm long with PTMT nuts |
| 52 | S & F 15mm Angle Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 53 | M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement |
| 54 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 55 | S&F PVC (SWR) bends any radius with access door, 110mm dia. |
| 56 | S&F PVC (SWR) vent cowl , 110mm dia. |
| 57 | S&F PVC (SWR) junction single, (single T) equal or unequal, 110mm dia. |
| 58 | S & F 15mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 59 | M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement |
| 60 | M&L 100mm bore Concrete bed (PCC 1:4:8 type D2) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; |
| 61 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed. |
| 62 | S & F Vitreous Cliina wash basin, wlhite, flat back, size 550x400 irun excluding taps, waste, chain and plug and porcelain stopper but including cutting for and pinning in ends of brackets or erecting stand |
| 63 | S & F Waste coupling of CP (half or full threaded) |
| 64 | S&F brass chromium plated shower rose with swival joints with shower arm all as specified and as directed. |
| 65 | S & F for waste pipe 32mm dia,complete with 80cm long flexible for WHB fixed complete all as specified and directed . |
| 66 | S & F Soap dish, CP , approximate size 160x 160x90mm |
| 67 | S & F vitreous China squatting pan, ‘Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete. |
| 68 | S & F for 10 Ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. |
| 69 | S&F PP-R Gate valves 20 mm outer dia of pipes (brass insert) as per requirement of the site |
| 70 | S&F Rotational mounded polythene water storage tank of 1000 ltrs capacity, (multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I. |
| 71 | M & L for One light point or one fan point controlled by one switch with 1.5 sq. mm size FRLS PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 72 | M & L for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size FRLS PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drawn through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 73 | M & L for One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size FRLS PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drawn through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 74 | M & L for One 3 pin socket outlet, 15 Amps, independent, with cables 4 sq. mm size FRLS PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 4.0 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drawn through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 75 | S&F Switch piano, flush type single pole, one way 5 Amp. |
| 76 | S&F Switch socket combination 2 in 1, 5 A flush type. |
| 77 | S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type Universal. |
| 78 | S&F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body. |
| 79 | Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete as specified. |
| 80 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete as specified. |
| 81 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete as specified. |
| 82 | S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for battern fittings complete. all as specified and directed by as engineer-in-charge. |
| 83 | S&F LED Bulb 9 watt cat part no LED PLUS 9W B22 WW 2 STAR LAMP complete all as specified and as directed by engineer-in-charge. |
| 84 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300 mm sweep with all fixing arrangement all as specified and as directed. |
| 85 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. |
| 86 | S&F of Single pole and neutral Sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20 Amps, 240 Volts, AC,50 HZ, completete all as directed and specified, including taking down old unserviceable plug socket and offering for credit. |
| 87 | M&L Wiring for circuit/submain wiring alongwith earth wire with 2x6.0 sq. mm +1x6.0 sq. mm earth wire sq mm sizes of FRLS for is PVC insulated copper conductor, single core cable in surface/recessed as required in PVC Casing capping. |
| 88 | S&F sheet metal enclosure distribution box 8 way SPN 230 volts with 200 Amps rated bus bar double door complete including connecting up all as specified . |
| 89 | Supply and fixing MCB 32 Amp SPN 240V, 10KA 'C' complete with connection testing and commissioning all as directed and as specified. |
| 90 | Supply and fixing MCB 5- 32 Amp SP 240V, 10KA 'C' complete with connection testing and commissioning all as directed and as specified. |
| 91 | Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized GI wire 4.0 mm as earthing lead by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and provision of concrete pit in PCC (1:3:6) type C1, pre-cast including RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm, reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways, one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil,and necessary testing complete all as shown on electrical plate No 5 of SSR Part –I (2009). |
| 92 | S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 4.0 Core including taking down old one. |
| 93 | S&F High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches of size 50 mm bore. |
| 94 | S&F 3-layer PP-R Polypropylene random copolymer) 32 mm concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc |
| 95 | Cutting existing steel tubing 25 to 32 mm bore for alterations or additions (Each cut measured) |
| 96 | M & L for replacement of PP-R Gate valves (brass insert) of size 32 mm bore as per requirement all as directed and as specified. Please Enable Macros to View BoQ information |
