Tender For Construction Of Hytec Building; 1 Excavation and refilling of available excavated soil for foundation as per drawing.Based on soil report we have assumed that hard strata will be available at a maximum depth of 8 feet 2 Supply and Fiiling of Gravel Available/Brought from Outside for Basement upto 16 Height 3 ATT Works at Foundation and Basement Levels 4 LDPE sheet of thickness 8mm used for waterproofing in basement 5 Providing and Laying of Reinforced Cement Concrete M20 Grade at all Levels 6 Providing and Laying of Plain Cement Concrete M10 Grade at Ground Level. 7 Providing and removing formworks with 12mm Plastic coated plywood so as get form finish with necessary wooden fame work, bolts, nits etc., with necessary supports including chemical releasing agent to avoid sticking of cement on the plywood at all heights, Levels to cast the member of any shape, size and complete and removal of formwork 8 Supplying, fabricating and fixing in position MS bars confirming to IS-432/High Yield strength deformed bars (Tor steel) confirming IS-1786 of Fe 500/550D grade of all dia for reinforcement in all RCC in situ works including Footing, Pedestal, Plinthbeam, Flooring works, Mezzanine Deck Florring works and heights including cost of straightening, cutting bending to shape fabricating and tying with 18G binding wire, providing and fixing cement cover blocks, wherever necessary etc., all complete as per drawings and specifications. The Rate to include cost of binding wire, cement cover blocks, all cuts and waists which will not be measured. Only laid weights will be measured including authorized laps 9 Supply, fabrication and erection in postion of Main Structural Members Columns & Truss using Rectangular & Square Hollow Sections(E250 Grade) and MS Plates(E250 Grade) for Base plates, Connection plates, Cold-formed Cpurlins and anchor bolts, as per the approved drawings, design and specifications. The work includes one coat of zinc chromate primer and two coats of enamel paint, transportation,loading, unloading, necessary cranes for erectionetc., required to complete the work. 10 Supply and fixing ofprofilecolour coated galvalume0.47mm thickness GI (curved) 550Mpa sheets for ROOFING as per approved drawing and colour with necessary sealant, EPDM metals washers, Bolts and nuts etc., to complete, method of measurement shall be based on the actual visible areaand the rate includes the required lapping of sheets. Also to be included is a layer of soundproofing under the GI sheet with PUF panel or rockwool, to reduce sound and improve heat proof. 11 Supply and fixing ofprofilecolour coated galvalume PUFF PANEL 100 mm thickness 550Mpa sheets for CLADINGas per approved drawing and colour with necessary sealant, EPDM metals washers, Bolts and nuts etc., to complete, method of measurement shall be based on the actual visible areaand the rate includes the required lapping of sheets. 12 Supply and laying of 1.0mm thick Decking sheet(JSW) 13 Supply and fixing ofprofile colour coated galvalume 0.47mm thickness 550Mpa sheets forACCESSORIES (corner flashing, drip flash,down take pipe,gutters) as per approved drawing and colour with necessary EPDM washers, bolt and nuts, sealant, etc , required to complete the work, method of measurement shall be based on the actual visible area and the rate includes the required lapping of sheets. 14 Plastering surfaces of Pedestals with CM 1:4, 15mm thick, smooth finish including racking joints, hacking, preparation of surface, scaffolding, forming grooves wherever necessary curing etc. 15 Windows-UPVC Sliding Windows 16 MS Rolling Shutters 17 Providing and Laying of Vetrified Tiles of approved makes using C.M 1:5 with proper grouting 18 Providing 150 tk Solid block wall using C.M 1:5 - For 3m Height 19 Plastering surfaces of walls with CM 1:4, 15mm thick, smooth finish including racking joints, hacking, preparation of surface, scaffolding, forming grooves wherever necessary curing etc. 20 Providing and Laying of Ceramic Tiles of approved makes for walls and floors at toilet portions using C.M 1:5 with proper grouting. - Full Height 21 Providing and Laying of ACP Works 22 Providing and Laying of False Ceiling at Roof 23 Electrical BoQ 24 WIRING WORKS 25 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. 26 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit,and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. 27 Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. 28 Supplying and fixing of following modular switch/ socket on a modular plate & G I switch box including connectionsas required 29 6 amps. socket controlled by 6 amps. one way switch 30 6/16 amps. socket controlled by 16 amps. one way switch 31 8 module POP UP Box comprising 5A CS Plug- 2Nos, Data Point -2 Nos 32 Supplying and fixing of following sizeMK premium base & lidCMSwith accessories including end caps, flexible internal/external corners flat angles,Flat tee, joint cover wherever necessary with cable divider, required type of modular box etcas per the site requirements 33 100mm x 50mm 34 50mm x 50 mm 35 Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface /recessed medium class PVC conduit as required 36 2 runs of 2.5 sq.mm and 1 run of 2.5 sqmm cable 37 2 Runs of 6.0 sq.mm and 1 run of 6sq.mm cable 38 4 runs of 10.0 sq.mm and 2 runs of 6 sq.mm cable 39 Distribution Board 40 Supplying and fixing following company madesheet steel, MCB distribution board, 240V or415 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc as required. ( without MCB/ RCCB/ Isolator). 41 4 way (4+12)three phase and neutral (double door MCB type) 42 8 way (4+24) three phase and neutral (VTPN double door MCCB type) 43 Providing and fixing following of rating and breaking capacity MCCB in the existing cubicle panel board including drilling holes in cubicle panel, making connections, etc as required. 44 36 kA,125 amperes 4 pole MCCB 45 Supplying & fixing of following ratings, miniature circuit breaker in the existing MCB/MCCB DBs complete with connections, testing and commissioning etc as required(2.10) 46 6 - 32 Amperes Single pole MCB 47 32A Triple pole MCB 48 63A four pole Isolator 49 Supplying & fixing of following metal clad/tempra plug and socket in a company made sheet steel enclosure on wall/in flush with wall with necessary connections and earth connections. 50 20A 1Φ MC Plug and Socketcontrolled by 20A DP MCB ( 3 PIN Socket and DP MCB will be in separate enclosures at different locations) 51 32A 3Φ MC Plug & Socket controlled by 32A TPN MCB 52 LIGHT FITTINGS AND FANS 53 Supplying, installation, testing and commissioning of pre wired following type of FTL /CFL fittings complete with all accessories and Tubes/CFL etc on wall/ceiling/false ceiling including connections with 1.5 sqmm FRLS PVC insulated single core copper conductor wires and earthing and welding work on existing truss etc as required. 54 600 x 600 mm recessed / surfacemounted VECTOR IV LCTLRF4-36-CDL LED Light firring or equivalent 55 DLYT CDR 219-18-57-SL NWH recessed/ surface mounted led Light fitting or equivalent 56 PROXIMA-R CDR 216-40-57-SL NWH recessed / surface mounted LED light fittingor equivalent 57 FLME SPOTCDR211-06-30-SL-NWH recessed/ surface mountedLED Fitting or equivalent 58 ROVER PLUS TFS 504-70-57-60D-SL-GL-NSGLED Fitting or equivalent 59 ORBIT CDS-201-20-57-HL2 NWH LED Fitting or equivalent 60 Infina compact 360 degree rotation focus 18W- 20WLED Track lighting on the existing rail with necessary connections. 61 Supplying and fixing of TRACK RAIL for fixing of light fittings on the existing truss with necessary clamps includingwelding works if necessary. 62 Supplying and fixing of 16mmx16mm Flexible Neon Silicon Profile Light - Front Bend IP65 24V STRIP/ ROPE LED Lighting 20W-25W per metre on the existing truss with suitable clamps and welding works if necessary 63 Supplying and fixing ofsteel condiuts (every 30cm length) for suspension of fans/Light fittings with special type of clamps from the Truss/ Burlin with necessary wiresas instructed by the Engineer In Charge. 64 Supplying and installation of 300mm sweep box typeexhaust fan withlouvers/ shutters in the existing opening and making connections and testing, commissioning etc as required. 65 DATA/VOICE 66 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.Single run of cable 67 Supplying, Erection in the existing concealed box / modular of singlePort Shuttered Faceplate for/with CAT 6I/O module with back box.The rate shall be include nessary accessories like screw, proper labelling with color code, etc ., as complete with all respects complying with relevant standard specification as mentioned in the Technical Specfication , as directed by the Engineer-in-charge. 68 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 69 Single run of cable 70 2 runs of cables 71 Supplying and fixing of following sizes of mediumclass PVC conduit alongwith accessories in surface/recess or cutting the wall and making good the same in case of recessed conduit as required.25mm 72 Supply, installation, testing and commissioning of Layer 2 managed switch with 24 ports (RJ-45) of make and model No. CISCO/C9200-24T-E complete with supply. The switch shall have 1 GB port to communicate with other switches including Passive components inbuilt 2 SFP ports including SFP modules, rack mountable termination accessories like Pigtails/ LIUs/ Convertors/ Splicing equipment, Patch panel, Patch Cord, etc complete as per specifications and as required. 73 CCTV 74 SITC of 16 channel NVR with storage capacity should store all cameras at 4.0 MP resolution for minimum 30 days backup @25 FPS as required. 75 Supply, installation, testing and commissioning of Layer 2 managed switch with 16 ports (RJ-45) ,POEas to support all camerascomplete with supply. The switch shall have 1 GB port to communicate with other switchesPOE compliant ports,rack mountable other termination accessories like Pigtails/ LIUs/ Convertors/ Splicing equipment, Patch panel, Patch Cord etccomplete as per specifications and as required. 76 Supply and fixing of 6 U wall mount indoor rackfront glass door with cam lock,PDU 6 x 5 amps and 1.5 meter feed cable and 3 pin top shelf 225mm fan 203V 90 cfm, cable manager, 1U pvc loops hardware packet of 20 assembled as required. 77 SITC of IP N/W colour bullet camera, 1/3 CMOS sensor, 4.0 MP resolution, varifocal 3-10 mm lens ONVIF COMPLIENT complete on wall/ ceiling with all required mounting accessories as required. 78 SITC of IP N/W colour Fixed bullet/dome camera, 1/3 CMOS sensor, 4.0 MP resolution,ONVIF COMPLIENT completeon wall/ ceiling with all required mounting accessories as required. . 79 CABLES & TERMINATIONS 80 Supplying& Laying of following sizes PVC XLPE insulated alu. Conductor armored 1100V LTUG cable in a 50 mm to 100 mm dia HDPE DWC pipein atrench of 50cm wide and 75cm depth including earth work excavation in all soils and sub soilsand back filling, consolidated in a regular interval of 25cm thick rammed and complying with standard specification. 81 4c x 16 sq.mm XLPE insulated armoured aluminium cable. 82 3.5c x 50 sq.mm XLPE insulated armoured aluminium cable. 83 3.5c x 150 sq.mm XLPE insulated armoured aluminium cable 84 Supplying and making end termination for following sizes alu. Conductor LT UG cable using suitable compression gland with required copper ferulles / socket and other jointing materials 85 4c x 16 sq.mm 86 3.5c x 50 sq.mm 87 3.5c x 150 sq.mm 88 Cable Tray 89 Supply,Installation, testing and commissioning of 300mm x 50mm x1.6 mmMS powder coated Perforated Cable Trayfor Data and voice/Electrical Cablewith suitable number of threaded rods ofL angle support fro the existing Truss with Anchor fasteners, Clamps, bolts,nuts including all the necessary welding works etc.,to suit site conditions as required 90 MV PANEL: Supply , Erection,Testing and commissioning of suitable size extendable floor mounting cubical type following LT Main Panel board suitable for 415V 3ph 4 wire 50Hz AC supply system fabricated in a compartmentalized design from CRCA sheet steel of 2mm thick for frame works and cover with 3mm thick removable gland plate ,cleaning and finishing with 7 tank process for powder coating with siemens grey having extensible type TPN aluminium alloy busbar of suitable capacity as per the incomer ACB /MCCB/SDF ratings with DMC/SMC busbar suppotrs with short circuit withstand capacity of 31MVA / 1Second ,bottom base channel of 75mmX 50mm X 5mm.BUS BARS: Bus bars will be electrolytic Aluminium R,Y,B, N(Black) PVC sleeved capable of carrying full load current for all the 3 phases and also neutral continiously. The current density of copper shall be designed for 0.8A per sqmm. The bus bar chamber should have properair ventilators.EARTHING: 2 separate run of 25 x 3 mm copper earth bus painted in green colour should be provided all along the panel and connected to the main grid. Interconnectios should be taken to metering chamber, MCCBs, ACBs, FSUs etc sothat all current carrying components areeffectively earthed.ADDITIONAL SCOPE OF WORKThe scope of work includes minor civil works like breaking of concrete floors ,construction of masonary trench , and suitable MS П type channels for the proposed panel as per the instruction from the Engineer in Charge. All the cable should be entry from top side of the panel with proper dressing with the existing cable tray. Necessary Panel drawings , QAP and GTP have to be approved by the Engineerincharge before fabrication.PANEL IIncomer250A 4P MCCB 36kA - 2Nos with microprocessor release for o/c , e/f and short circuit protection, Breaker ON/OFF/Trip indication Lamps as twoincomers from different source of supply.Outgoing125A 25kA TPN MCCB with microprocessor release for o/c , e/f and short circuit protection, Breaker ON/OFF/Trip indication Lamps and all other requiredaccessories – 4 Nos.63A 25kA TPN MCCB with microprocessor release for o/c , e/f and short circuit protection, BreakerON/OFF/Trip indication Lamps and all other required accessories – 4 Nos.250 A Alu bus bars for 3phases and also same forNeutralBoth incomers are comprising with 3 phase indication lamps with toggle switch, microprocessor based digital multi function meter with communication port and the facility for active and reactive power measurements with required CTs and control fuses etc.Necessary Spreaders / extended copper bus bars of suitable rating with required holes should be provided for the cable and bus bar terminations .All switch gears should have front oerated hand and the handle should be pad lockable type in both ON/OFF positions.The work should be inclusive of providing interlocking arrangement for the 2 incomers byproviding 2 locks and 1 key. 91 EARTHING 92 Earthing with GI earth plate 600x600x6 mmthick including acessoriesand providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7m long etc with charcoal/coke and salt as required. 93 Supplying and laying of following size earth flats at 0.50 mt below the earth including soldering/welding as required 94 Single run of 8 SWG bare copper conductor withneccessaryend connections 95 Single run of 8 SWG bare copper conductor withneccessaryend connections 96 Plumbing BoQ 97 PART A: SANITARY FIXTURES AND CP FITTINGS Collecting from stores, shifting to the place of installation and fixing of glazed White colour Vitreous China wall mounted water closet fischer bolts with CP bolts / nuts and with Open flush tank with dual flush, solid plastic seat and lid with heavy duty CP hinges and rubber buffers and flap etc. The work shall include cutting making of walls and floors etc. Notes: The rate quoted by the vendor shall be inclusive of necessary consumables like brass screws, wooden plugs, white cement etc., required if any, shall be arranged by the contractor. Only drilling machines shall be used for making the holes in the walls for fixing, no wall jumper and hammer will be allowed. a)Collecting from stores, shifting to the place of installation and fixing of CP health faucet b)CP angle stop cock with wall flange. c) Hand operated spray unit (instant type) with CP Crutch and PVC flexible tube of 1.0m length Includes supply and fixing 98 Collecting from stores, shifting to the place of installation and fixing and commissioning of White colour, make and model vitreous china rectangular wash basin GI rag bilts, 15 mm dia CP pillar cock 32mm dia CP waste coupling with plug and chain and including PVC connecting pipe, 32mm dia CP brass bottle trap, one no of 15mm dia CP angle stop cock with wall flange. The works shall include cutting in wall and making good the walls & floors. Notes: Conditions mentioned in item no.1 shall be applicable includes supply and fixing 99 Collecting from stores, shifting to the place of installation and fixing of White colour, make and model and size viterous china concealed soap dish including cutting and setting in walls with white cement joints making good of walls. Notes: a) Conditions mentioned in item no.1 shall be applicableincludes supply and fixingincludes supply and fixing 100 Collecting from stores, shifting to the place of installation and fixing of 600mm long 25mm dia CP brass superior quality towel rail with brackets, and flange with concealedbrass screws etc., including cutting & making good the walls. Notes: Conditions mentioned in item no.1 shall be applicable 101 Collecting from stores, shifting to the place of installation and fixing of 15mm dia CP angle stop cock with wall flange etc.(for aqua guard point in Each floor), 102 PART B : CPVC PIPES AND FITTNGS (INTERNAL AND EXTERNAL WATERSUPPLY):Providing & fixing of CPVC pipes confirming to ASTM standard including all CPVC fittings like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours etc. making holes, including chasing in solid block masonry walls with groove cutting machine to required width and depth, making bores in walls, foundations and RCC slabs, making good the walls and bores in CC or CM 1:3 as applicable clearing the debris, grouting of concealed pipes, MS hooks for fixing pipes and making good the walls and floors.Note: Strictly use SDR-11 grade ASTRAL - CPVC pipe and fittings for internal hot water supply up to 50 mm dia. INTERNAL (CONCEALED IN WALL):COLD WATERSUPPLY 103 20 mm dia (SDR-11) 104 32 mm dia (SDR-11) 105 Providing & fixing of CPVC pipes confirming to ASTM standard including all CPVC fittings like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours hours etc., fixed on to the wall in vertical shafts / terrace with fabricated MS brackets of suitable size with GI U clamps, bolts, nuts and GI washers including MS brackets including making goodthe walls and floors. 106 Providing, fixing testing and commissioning of CPVC ball valves (Astral / Ashirwad make) including unions etc., Complete 107 Providing, fixing, testing and commissioning of water meter confirming to IS 2372 - 1981, kranthi / dasmesh make with direct reading dia in KL with all integral parts of gun metal or brass with neccesary fittings such as threaded pieces, unions, check nuts complete.a)50 mm dia 108 Part C: PVC SOIL,WASTE,VENT PIPES AND FITTINGS ( INTERNAL & EXTERNAL)Providing, fixing, testing and commissioning of PVC soil, waste and vent pipe confirming to IS 13592 of SWR quality 4 kg / sq.cm pressure rated including all fittings, like Bends, Tees, Elbows, Collars, junction, offsets, access pipes, jointing with solvent cement followed by application of leak proof adhesive like FRP paste & laid on floors inside the toilets kitchen and utility to the required slope including making necessary bores in walls as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete.Notes: Wall chasing shall be done with chasing machine to required lines and levels. INTERNAL (TOILET & KITCHEN): 109 75mm dia (4kg/sq.cm pressure rated) 110 110mm dia (4kg/sq.cm pressure rated) 111 40mm dia (4kg/sq.cm pressure rated) 112 Providing, fixing, testing and commissioning of PVC soil, waste and vent pipe confirming to IS 13592 of SWR quality 4 kg / sq.cm pressure rated 10mm, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI U clamps with bolts, nuts and GI washers complete, for soil and waste pipe lines laid in vertical shafts.EXTERNAL (IN SHAFTS):110mm dia - 4kg/sq.cm pressure rated (Soil pipe) column etc. complete. 160mm dia (6kg/sq.cm pr. Rated) 113 Providing, fixing, testing and commissioning of PVC trap of self cleansing design moulded or fabricated, if not available in size mentioned below, with or without vent arm jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste including PVC extension pipe for PVC / floor trap for with surface preparation with finishing etc., complete size: 100 mm dia x 400 mm length. Making good the floors. 114 Providing, fixing, testing and commissioning of PVC connecting collar (fabricated) for connecting FT & WB bottle trap pipe, complete jointing with solvent cement followed by application of leak proof adhesive like FRP paste including cutting and making good the walls and floors. Size 110 mm x 40 mm dia 115 Providing, fixing, testing and commissioning of CP grating with rim including setting in floor with white cement mortar and making good the floor (Chilli Make).125 mm dia 116 Providing, fixing, testing and commissioning of ready made PVC gully trap (ISI brand only) of 100 x 100 mm size with 100 mm dia outlet. and also providing suitable size of cast iron grating, including 40 mm thick precast ready made light duty RCC cover slab, clearing the surplus material, earth etc. complete. 117 100mm x 100mm size `P/S trap 118 MS l angle frame of size 50 x 50 x 6 mm thick. 119 Regural soil and Excavating Soft rock 120 Providing, fixing, testing and commissioning of PVC rain water pipe confirming to IS 13592 of SWR quality 4 kg / sq.cm pressure rated 10mm, including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, offsets, access pipes, jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste, fixed to wall with properly fabricated MS bracket of suitable size, GI U clamps with bolts, nuts and GI washers complete, for rain water pipe lines laid in vertical shafts 110mm dia - 4kg/sq.cm pressure rated (for Terrace) 121 Providing and fixing Constructing storm water catch basin internal clear dimension as mentioned below with 230 mm thick brick masonry wall using 1st class table moulded brick in 1:4 over a bed of 150 mm thick 1:4:8 PCC in cement motar 1:5 (1cement: 5 fine sand), precast perforated RCC top slab in 1:2:4 Mix (1 cement: 2 coarse sand: 8 graded stone aggregate)Inside size of 450 X 450mm & depth not exceeding 600mm including providing 450 x 450mm precast perforated RCC cover with 50 x 50 x 6mm thick with MS L angle frame 122 Construction of percolation well / rain water harvest pit of 1.2 m dia and 3m deep with precast RCC rings, coveringthe top with RCC slab including supply and fixing 600 x 600 RCC MH cover CI / MS rungs etc. The quoted rate shall include earth work excavation, back filling, removing excess earth and making good the floor. The percolation well harvest pit shall be constructed as per the detail drawings and specification shall conssit of:c) Allernate layers of brick bats, activated charcoal, gravel, pebbles and toped with fine sand for good infiltration.d) Bore hole of 160 mm dia from the bottom of percolation pit for a depth of 6m from the bottom of percolation pit drilled by using auger manually
