Tender For Certain Misc Repair Under Age Br I And Age Em I Of Ge 865 Ews; 1 Dismantling floor, hearth or wall tiling including wall cement mortar, bedding (But not backing ) and rubbish of premises complete all as directed. 2 M&L for 25 mm thickPCC 1:2:4 type B1 using 20mm graded stone aggregate as in sub base of floorcomplete all as directed by Engr-in-charge. 3 M&L Non-Skidceramic Coloured Tiles 7 to 8mm thick(squre/rectanglar) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over 15 mm screed bed or bedding layers in cement mortar 1:4 Set and Jointed in neat Cement Slurry and Pointed in Colour Cement to match, complete all as specified and as directed. 4 M & L for joint free non-Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge 5 M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed. 6 Taking down of shutter of any discription exc 1 Sqm and n exc 2 Sqm each comptete all as directed by Engr in chage 7 S &F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails.M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling& fixing in the frame at site complete all as specified and as directed by Engineer-in-Charge. 8 S&F for 35mm thick2nd class hardwood plain framed paneled shutters (twopanels) with panels with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces and fixed to chowkats , complete all as directed by Engr-in-charge. 9 S&F 150mm long aluminium anodized, barrel tower bolt of extruded sectioncompleteall as specified and as directed. 10 S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed. 11 S&F 100mm long aluminium anodized, butt hinges of extruded sectioncompleteall as specified and as directed. 12 S&F in repair250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed 13 Dismantling water tank exc 250 & n exc 500 litre complete all as specified and directed. 14 S&F rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, complete all as specified and as directed. 15 Taking up or down 25/32 mm bore stee /PPRl tubing and connections and set aside for re-use or removal to store 16 S & F 25mm dia3 layer PP-R polypropyene random copolymer concealedpipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge. 17 S&F viterous China squatting pan or Orissa pattern580 x 440 mm white with integral foot rest (excluding cistern)with front or back inlet ant pattern as in repairs incl bedding with PCC type B-I 1:2:4 , using 20 mm graded crushed stone aggregate 18 S&F sand cast iron P or S trap 100mm bore, complete all as specified and as directed. 19 S&F flushing cistern of PVC 10 ltr. cap. with dual flushing system, white colour, valveless syphonic action type,low level, with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified and directed. 20 S&F in repairs 15mm dia Angle stop valves, fancy type chromium plated with lonk shank and cup cast copper alloy (concealed type), screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipescomplete all as spd. 21 S&F CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4,100mm dia, complete all as specified and as directed 22 S & F in repair 15 mm bore pillar taps, fancy type Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe. 23 S&F in repair towel rod CP 60 cm long between flanges and including all accessories like brackets/screws etc as recommended by manufacturer and complete fixed in position complete all as specified. 24 S&F In repair viterous China urinal half stall type white including CP spreader, waster pipe etc 25 M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water dranage pipeslaid in trenches and jointed all as specified including dismantling etc 26 S & F in 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed. 27 Dismantling plain or corrugated steel /fibre sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed. 28 S&F Pre painted galvalumealuminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws as specified. 29 Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and gourd bars or grating complete all as spd and as directed by Engr-in-Charge. 30 S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar workconfirming to Fe-290, Gde-E-165 complete all as specified and as directed. 31 M&L for preparation new steel surfaces of any description, not otherwise described, over 10cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and as directed. 32 Demolition of cement concrete in ground floor and pavings nexc 15cm thick below or above ground level complete all as specified and as directed. 33 Excavating in post holes (or similar holes) each n exc 0.5 cu.m, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface of hard / dense soil. 34 M&L for PCC type D2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation and mass concrete, complete all as specified and as directed. 35 Demolition of precast concrete block walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed 36 M&L for pre cast solid block masonry set in CM 1:6& casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone aggregate complete all as specified and directed. 37 M&L for 10mm thick rendering on other than fair faces of Bbrickworks finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed. 38 M & L Preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls. 39 M&L for Cement concrete type D-2,1:4:8 (40mm graded aggreate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc. 40 M&L sand fillingunder floors in foundation and laying interlocking paver blocks including watering and consolidation complete all as specified and as directed by Engr-in -Charge. 41 M&LMachine pressed precast concrete interlocking paver block any shape and sizewith grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 grade as specified and directed by EIC. 42 M & L Cement concrete work in pavement/ hard standing of flexural strenth 40 kg/per square centimetre in field using 400 kg of cementper cubic metre , thickness of concrete 25 cm or less specified and directed by Engr-in-charge 43 Supply only polyester triangular fibres as secondary reinforcement in all type of concrete and mortar 44 M & L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade A for 100mm thick concrete . 45 M&L forming contraction (Dummy) joints 65mm deep X 10mm wide , filled with sealing compound Grade A 46 Removing of demolitiong material n. exe 50m and depositing where directedat a level n, exe 1.5 km above the starting poit complete all as spd and directed by Engr-in-Chrge. 47 M&L priming surfaces and applying normal treatment(for moderate condition ) for App based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforment with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surfaced application including preperation of new surface of membrane and applying two coats of Alumminium paint, complete all as specified and as directed by Engr-in-Charge. 48 Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as spfd and directed by Engr-in-Charge. 49 Point wiring complete with 1.5Sq.mm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC Casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth leadall as specified and directed for the followings:- 50 (a) One light / fan point controlled by one way switch complete all as specified and directed. 51 (b) One switch socket outlet 6 Amps, 230 volts point on Same board complete all as specified and directed. 52 (c) One switch socket outlet 6 Amps, 230 volts point on independent board complete all as specified and directed. 53 All as item No 48.00 above, but using cables 4 Sq mm size complete all as specified and directed. 54 Supply and replacement of Switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed . 55 Supply and fix in replacement of socketout let two in one5 pin 6 Amps flush type.230 volts complete all as specified and directed. 56 Supply and replacement of switch Socket combination out let multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all pecified and directed . 57 Supply and Fixing only in Replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 58 Supply and replacement of Ceiling rose, surface Bakelite three terminals complete all as specified and directed. 59 Taking down old unserviceable high bay light and supply and fix in replacement LED high bay light fitiing 150 watt 230 Volt AC outdoor type with hiugh pressure die cast aluminium hiusing and heat resistant complte with driver,lamp cracket with impact and corosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and drected. 60 Supply and laying in replacementofXLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 16 Sqmm 2.0 core laid in trences or passing through pipes.ducts or fixed to walls/poles c including taking down old unserviceable cable covers completer all as specified and/or directed by Engineer-in-Charge. 61 Deduct Schedule of Credit of Rs (-) 86769.00 (Minus) as listed in Schedule A (Contd). Contract Sum shall be arrived after deducting the credit amount.Note :- Tenderers will not quote against this item being a firm amount.
