Provn Of Certain Sanctioned And Minor Works Under Age B/R-Ii At Afs Thanjavur; 1.00 Excavation over area not exceeding 1.5 m deep and getting out in hard dense soil complete all as specified and as directed. 2.00 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 3.00 Material & Labour for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. 4.00 M&L 100mm thick plain cement concrete 1:2:4 Type B-2 (40 mm graded stone aggregate ) as in floor finishedf with fair and even complete all as specified and as directed. 5.00 M&L 50mm thick plain cement concrete 1:3:6 Type C-1 (20 mm graded stone aggregate ) as in floor finished with fair and even complete all as specified and as directed. 6.00 M&L forming contracton (Dummy) joints 65 mm deep x 10 mm wide, filled with sealing compound Grade A complete all as specified and as directed. 7.00 M&L forming 20 mm thick expansion joint filled with pre formed bituminous filler and top 30 mm primed and sealed with sealing compound, Grade A for thickness of concrete slab 150 mm complete all as specified and as directed. 8.00 M&L forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and as directed. 9.00 M&L formwork to edges of concrete flats, breaks in floors for fair finished surfaces of concrete complete all as specified and as directed. 10.00 Excavation in post holes of any description and any thickness including (or Similar holes) each post holes not exc 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance not exc 50m and making good surface in hard /dense soil complete all as specified and as directed. 11.00 M&L plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concreting complete all as specified and as directed. 12.00 S&F steel work in tubular truss including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979 of grade St-240 complete all as specified and as directed. 13.00 S&F bands, straps, supports or stays for rainwater, plain angle cleat for securing purlin, knee piece inserts, two way and three way straps, plate washer and similar small articles, confirming to Fe-290 Gde E-165 complete all as specified and as directed. 14.00 S&F plates (plain or chequered) Channels, square, cut or notched (ordinary and counter sunk) forming holes without any attachment of Fe-410-W (Grade E-250) quality A complete all as specified and as directed. 15.00 S&F mild steel works such as wind ties for roof including securing with bolts etc and similar work using rolled section confirming to Fe-290 Gde E-165 complete all as specified and as directed. 16.00 S&F pre-colour coated high tensile strength corrugated galvalume sheet roofing with yield strength (550 MPA) prepainted with aluminium (55%) and zinc (45%) alloy coating applied through continuous hot dip process having total coated thickness (TCT) of 0.50mm with minimum coating mass on both sides @ 150gms/sqm in length and width as per site condition fixed with complete accessories as per manufacturers instructions through specialist agency and as per profile and shade as approved by GE complete all as specified and as directed. 17.00 S&F plain fibre glass reinforced translucent sheets of 2mm thickness side lap fixed with coach screw and washer in roof, wall etc as per site condition fixed complete acessories as per manufacturers instructions through specialist agency and as per profile and shade as approved by GE complete all as specified and as directed. 18.00 M&L preparation of new steel surfaces of any description over 10 cm in width or girth and apply two coats of synthetic enamel paint over one coat of redoxide primer complete all as specified and as directed. 19.00 M&L drilling 12mm dia holes in to the coloumn/beam/ wall of any decsription at in any position and fixing the hole by anchorage bolts with two-component polyester resin anchoring grout chemical for firmly fixing complete all as per manufactures instructions complete all as specified and as directed. 20.00 S & F mild steel sheet 1.25 mm thickness for eaves gutter, galvanised class 3, half round with rounded edges of dia 150mm complete all as specified and as directed 21.00 S & F eaves gutter (internal or external) or nozzle pieces (outlets) of mild steel sheet 1.25 mm thickness, galvanised, class 3, 150mm dia complete all as specified and as directed 22.00 S & F drop ends (for spigot or socket ends) or nozzle of mild steel sheet 1.25 mm thickness, galvanised, class 3, 150mm dia complete all as specified and as directed 23.00 S & F stop ends (for spigot or socket ends) or nozzle of mild steel sheet 1.25 mm thickness, galvanised, class 3, 150mm dia complete all as specified and as directed 24.00 M&L roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed. 25.00 M&L brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed. 26.00 M&L cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in kerbs and ramps cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. 27.00 M&L Cutting opening in cement concrete walls (any descript-ion) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc with or without reinforcement complete all as specified and as directed. 28.00 M&L Cutting holes in brick walls inbuilt in cement mortar or cement lime mortar and stone walls for inserting holdfasts and making good dismantled portion in cement mortar 1:3 and applying two coats of exterior emulsion paint exc. half brick but not exc one brick complete all as specified and as directed. 29.00 M & L Precast cement concrete block masonry with solid blocks with 1:3:6 type C1 (using 20 mm graded stone aggregate), exc.10 cm in width and setting in CM 1:6 complete all as specified and as directed. 30.00 M&L plastering in CM 1:6, 10 mm thick on walls finished even and smooth w/o using extra cement complete all as specified and as directed. 31.00 M&L preparation of new plastered surface of wall and applying two coats of plastic emulsion paint of any colour and shade and pattern ) Pattern and shade consist of combination of two or more colour) over a coat of primer complete all as specified and as directed. 32.00 M&L 100mm thick plain cement concrete 1:4:8 Type D-2 (using 40 mm graded stone aggregate ) as in floor finishes surface fair and even complete all as specified and as directed. 33.00 M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 34.00 M & L providing precast cement concrete as in cover slabs (for manholes) type B1 1:2:4 using 20 mm graded stone aggregate and set in cm 1:4 including necessary formwork complete all as specified and as directed. 35.00 M&L spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and as directed. 36.00 M&L Demolition of Reinforced Concrete of any description and in any position not otherwise specifically provided for including gate pillar etc complete all as specified and as directed. 37.00 M&L excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth ; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard and dense soil complete all as specified and as directed. 38.00 M&L PCC 1:4:8 type D-2 using 40 mm graded broken stone as in foundation , filling and mass concrtete complete all as specified and as directed. 39.00 M&L RCC (1:1:2) nominal mix using 20 mm graded Stone aggreagte for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed. 40.00 M&L RCC (1:1:2) nominal mix using 20 mm graded aggregate for Columns, pillars, piers, posts complete all as specified and as directed. 41.00 M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough complete all as specified and as directed. 42.00 M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions including sup- ports, overhangs, etc. also splays between floors and beams, finished etc. complete all as specified and as directed. 43.00 M&L returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. 44.00 M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bendin spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 45.00 M&L TMT bars, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed. 46.00 M&L framed work as sliding doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening complete all as specified and as directed. 47.00 M&L Granite 18 mm thick of any type work (table rubbed and polished) in steps, treads jambs, pillars, window- cills, cooking platforms, other plateforms and like in over and including 10mm thick backing coat in CM 1:4 cmplete all as specified. including pointing in white cement or colour cement (1:2) using marble dust with admixture of pigment to match with shade of granite( including moulding etc) complete all as specified and as directed. 48.00 Supply and installation of SLIDING GATE AUTOMATION 1000 KG-LIVFUTURE MODEL SD-1015 1 Sliding Gate motor with control card 1000 Kg motor with control box with panic and manual button, 2 Nos remote Suitable for up to a 55mtr opening and Gate Weight Max. 700 ~ 900kg ,Environmental protection working temp -20 to +50 degrees C. rain Proof and Standard opening time to 12 feet gate 10 to 12 seconds including Remote control operating distance 165 feet. The Kit weights 10Kg Apx and Over-load and Over-heat protecting function, Safety Sensor, Extra Remote, Extra Gear Rack including Installation, Testing & Commissioning Charges Packing and Forwarding Charges complete all as specified and as directed. 49.00 M&L cutting of road and pavement of any description and any position with not exceeding 45 cm and depth not exceeding 30cm for laying cable and conduit of any description and filling the same after laying the cable with PCC 1:2:4 and finishing the surface even and fine withoue using extra cement complete all as specified and as directed. 50.00 Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed. 51.00 Fixing only chain link fencing including line wire, any mesh, size and type to any type of standards, rails, straining bolts, etc including provission of binding wire complete all as specified and as directed. 52.00 S & F galvanised 2 stranad steel barbed wire 2.24 mm dia barbed with 2 mm dia barbed at 75 mm spacing s and straing and fixing to any type of standard rail strain -ing Bolt , including, securing or tying at crossing with and provision of galvanised mild steel wire , staples or steel pine etc complete all as specified and as directed.
