Tender For Maint Of Misc B/R Services In Sector-C And D In Akhnoor Mil Under Ge (South) Akhnoor.; 1 Dismantling posts or struts (wood, steel or R.C.C.) any section, including takingout embedded portion and making good disturbed ground posts embedded in concrete.. 2 Excavating in post hole (or similar hole) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in any type of soil, complete all as specified. 3 Mild steel posts and struts in fencing posts including cuttingtops to shape as directed, drillingholes, notching for wire etc; flate iron fillets (for securing chain link fencing) including all necessarydrilling, bolting or rivetingetc, andsimilar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 4 M&L for mild steel galvanized concertina coil fencing with punched tape concertina coil of any dia as per site requirement, 10 metre openable length (total length 142 mtrs), having 50 Nos, rounds per 6.0 metre length, spring core wire (2.5 mm dia galvanized wire) of high tensile strength not less than 400-450 gm/Sqmm with tape (0.52mm thick) and fixing the same with existing Y-shaped angle iron placed 2.0mtrs apart and with 6 horizontal R.B.T. (Reinforced Barbed Tape) wire, stud tied with G.l. staple sand, 125 to 127 Nos. of G.l. clips in one coil, to retain horizontal, including necessary nuts and bolts, including taking down existing rusted / damaged concertina coil complete all as specified and as directed by Engineer-in-Charge. Note:- Weight of coil shall be ascertained through BoO. 5 Dismantling of barbed wire fencing from posts etc complete and neatly coiled on rough drumsas directed 6 S&F galvanised, 2-strand, steel barbed wire 2.24mm dia barbed with 2.0 mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified and as directed by Engineer-In-Charge. 7 Fixing only chain link fencing including line wires(steel wire), any mesh, size and type to any type of standards, rails, round bars, straining bolts etc including provision of binding wire compete all as specified and directed by Engineer in Charge. Note : (i) Supply of chain link and line wire shall be measured and paid seperately. (ii) Whereever required the cost of Grubbing up bushes , tree trunks portion not exc 30CM girth including cutting of trees/bushes grown over wall and roofs digging out roots and making good disturbed area with earth filling and levelling shall be deemed to be included in the quoted Rates. 8 Supply only mild steel galvanized chain link fencing of any mesh, size and any type (as decided and approved by GE) complete all as specified and directed by Engineer in Charge. Note: The weight of chain link fencing shall be ascertained by BOO as ordered by GE and payment shall be made accordingly. 9 Mild steel round bars 10mm dia and over cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., Fe-410-W (Gde E-250) ,complete all as specified and as directed. 10 Mild steel screw bolt (machine made) 5 to 10 mm dia with hexagonal or squre heads at one end and screwed the other end,each screwed end to be fitted with washers and one hexagonal nut ,n exc 5cm long all as specified. 11 Mild steelflat iron40x6mm and struts in fencing including cutting tops to shape as directed,drilling holes, Fe 290 gde E-165 complete all as specified. . 12 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed . 13 Dismantling wrought iron or mild steel work/ structural steel work of any description not otherwise provided for ,complete all specified and directed. 14 Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. 15 Demolition of cement concrete (reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. 16 Demolition brick work or stone/boulder masonry built in cement mortarincluding all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and precast concrete articles ,complete all specified and directed. 17 Taking down cement plaster from brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc.,complete all specified and directed. 18 M&L for plain cement concrete 1:3:6 type C-1(20mm graded crushed stone agreegate) as in surface channels and drains complete specified and directed. 19 Extra for forming fair finished drain or channel 30 CM inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc., complete all as specified and as directed. Note: inner girth shall be measured. 20 Removing excavated material (soils) not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and as directed . 21 M&L for plain cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregates as in foundation filling and mass concrete in foundation including necessary formwork,complete all as specified and as diected. 22 M&L for plain cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in hold fasts,copings, bed plates, kerbs, water troughs and the like includingweathering, slightly rounded or chamfered angles and throating, including necessary formwork , complete all as specified and as directed. 23 M&L for providing precast cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in cover slabs for manholes etc, set in cements mortar 1:6, complete all as specified and as directed. 24 S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.,complete all as specified and as directed. 25 M&L for machine pressed precast concrete interlocking paver block of any size and shape confirming to IS 15658-2006 of 60mm thickness M-35 grade over 75 mm thick plain cement concrete 1:5:10, type E-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and fair including necessary formwork,including 25mm sand cushioning ,complete all as specified and as directed 26 M&L for brick work with sub class `B bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 ,complete all as specified and as directed . 27 M&L for brick work with sub class `B bricks, straight or curved on plan toany radius in half bricks thick wall built in cement mortar 1:6, complete all as specified and as directed . 28 M&L for brick work with sub class `B bricks,on edges in half bricks thick wall built in cement mortar 1:4, complete all as specified and as directed . 29 M&L for brick work with sub class `B bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4, but except bricks,complete all specified and directed. 30 Flush pointing to block in course or ashlar masonry or concrete block walling in cement motar 1:4, complete all specified and directed. 31 Rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces , finishing the surface even & smooth without using extra cement, complete all as specified and as directed . 32 M&L Glazed ceramic tiles in vertical surface 450X 350X 7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles over 10 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work ,complete all as specifed and directed. 33 M&L for plain cement concrete M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate), as in fixing angle iron fencing post including necessary formwork , complete all as specified and as directed. 34 M&L for 50mm thick, plain cement concrete M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate),as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight,including necessary formwork , complete all as specified and as directed. 35 M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over priming plastered and other surfaces with alkalie resistant priming paint , complete all as specified and as directed. 36 M&L for preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over one coat of white primer, complete all as specified and as directed 37 M&L for applying two coats of synthetic enamel paint over a coat of zinc chrome/red oxideprimer including preparation of new or previously untreated steel surfacesover 10 cm in width or girth , complete all as specified and as directed. 38 M&L for applying one coat of synthetic enamel paint including preparation of old or previously treated steel surfacesover 10 cm in width or girth , complete all as specified and as directed. 39 M&L forcomplete removal of existing treatment from old decorated surfaces of wall and applying two coats of cement based paint, complete all as specified and as directed . 40 M&L forcomplete removal of existing treatment from old decorated surfaces of wall and applying one coat of cement based paint, complete all as specified and as directed . 41 M&L forcomplete removal of existing treatment from old decorated surfaces of wall and applying one coat of exterior emulsion, complete all as specified and as directed. 42 Chequered cement concrete coloured tiles size 300mmx300mmx20/25mm thick, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 20mm thick screed bed or bedding layer in cement mortar 1:6 laid over and including 75mm thick sub base of nominal mix plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate, complete all as specified and as directed .
