Tender For Work Of Fabrication And Errection - Dismantling, Fabrication And Erection Of Old / New Pipe Lines Upto Size 12. Dismantling, Fabrication And Erection Of Tee Upto Size 12. Dismantling, Fabrication And Erection Of Nipples Upto Size 12. Dismant, ghosi-Uttar Pradesh

Tender For Work Of Fabrication And Errection - Dismantling, fabrication and erection of old / new pipe lines upto size 12.Dismantling, fabrication and erection of Tee upto size 12.Dismantling, fabrication and erection of Nipples upto size 12.Dismantling, fabrication and erection of Cross upto size 12.Dismantling, fabrication and erection of Bend upto size 10.Dismantling, fabrication and erection of Flange upto size 12.Dismantling, fabrication and erection of Reducer upto size 12.Dismantling, fabrication and erection of Blind upto size 12.Dismantling, fabrication and erection of Tee above 12 size.Dismantling, fabrication and erection of Nipple above 12 size. Dismantling of heavy structure. (above 02 ton)Fabrication and erection of heavy structure.Dismantling of light structure.Fabrication and erection of light structure.Hard facing on the teeth of under feed roller of mill.Making and installing new scamper in place of worn/cut scamper of under feed roller of mill.Cutting and removing the throat teeth of under feed roller and fabricating and installing teeth as per drawing and doing hard facing.Making the worn juice ring of side rollers of mill with new 6/8 mm thick plate as per sample.Properly replace both the pipes of the mills corroded Ku-Ku conveyor and fit them in the fitted trough and give trial.Cut the corroded runner of cane carrier, rack carrier, bagasse elevator and bagasse carrier and put them in the scum yard and make a new runner with 50/65 mm flat, install it and give trial.Cut the corroded/worn side plates of cane carrier and put them in the scum yard and fit them with new 6/8 mm thick MS plate.Cut out the discharge suit fitted below the fiberizer and put it in the scum yard and make it with 12 mm plate and give satisfactory trial.Replace the corroded bottom top and side plates of rack carrier with 08 mm plate Cleaning and painting of the inside and outside of the boiler chimney.Cleaning and whitewashing the condensate receiving tank of the boiler.Dismantling, fabrication and erection of the delivery line of bagasselo fan.Cutting and removing the plate on the top of the boiler and replacing it with a new plate.Cutting and patching the corroded side and bottom plates of bagasse elevator, RBC.Cutting and removing the side plates of boiler no. 1, 2 and 3 and replacing the corroded plates and as per requirement making and installing new plates from 5/3 mm plate as per sample.Cutting and removing the corroded plates of the expansion joint of air heater/economizer of boiler no. 1, 2 and 3 and replacing it with a new joint as per sample and giving trial.Work of making and installing expansion bellows at various places in the side plates of boiler no. 3 as per the instructions.Cutting and removing the corroded air suit of boiler no. 1 and 2 and making a new suit from new plate and installing it and giving trial.Dismantling, fabrication and erection of damaged ribs of juice heater/vapor line juice heater.Fixing a blind in the pipe above the vapor line juice heater and doing its hydraulic test.After testing, removing the blind and joining the pipe as before.Dismantling of brass tubes of juice heater Making and installing the telescopic box of the clarifier as per the sample along with all its connections. Making cones from MS plate as per requirement and fitting as per instructions and giving trial. Measurement will be done on the basis of bigger dia.Dismantling of brass tubes of pansFittings related to brass tubes of pansHydraulic testing of pans (up to 100 PSI)Cutting and removing the corroded plates of the sew all of pans and making and fitting them with new plates and giving trial.Cutting and removing the weak parts of molasses tanks installed on pan floor and fitting a new one and giving trial.Make and fit rings on the vapor pipe of evaporator/pans from angle/flat iron/MS plate etc. as per instructions.Dismantling the top cover of the sew all of pans and making and fitting a new one by giving support etc. as per sample.Strengthening of pan bodies from inside/outside with MS plate/angle as per instructions.Dismantling the top cone of pans Make a new one according to the sample and install it. While working, stop the save all fitted on it by giving support and after the work is done remove the support and give a successful trial.

INR 300 /-

Refer document

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB