Tender For Provision Of Certain Minor Works Under Ge Gurdaspur.; 1 Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in any type soil, complete all as specified and directed. 2 Material and labour forexcavating in trenches incl soft/loose soiln.exc 1.5m wide and n.exc 1.5m deep for foundation in any type of soil and getting out etc complete, all as specified and directed. 3 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete, all as specified and directed. 4 Removing excavated material exc. 50m n.exc 100mand depositing where directed at a level n exc. 1.5 m above the starting point complete, all as specified and directed. 5 Material and labour forfactory made , machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 25mm thick sand cushioning, complete all as specified and directed. (Note : The cost of sand cushion is included initem rate quoted by the contractor). 6 Material and labour for hardcore(broken stone) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface 7 Material and labour for hardcore (broken stone or boulders) of guage exc 63mm but n exc.100mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed toa true surface complete all as specified and directed. 8 Material and labour for RCC1:1.5:3 (nominal mix)(using 12.5 mm graded crushed stone aggregate) as in foundations, including rafts, footings,foundation beams; plinth beams; bases for columns,slab etc all as directed. 9 Material and labour for RCC1:1.5:3 (nominal mix) (using 20mm graded crushed stone aggregate)in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified 10 Material and labour forRCC1:1.5:3 (nominal mix) ( 20 mm graded crushed aggregate stones) as in beams, lintels, cantilevers, bressummers complete, all as specified and directed. 11 Material and labour for RCC1:1.5:3 (nominal mix) (using 20mm graded crushed stone aggregate)in columns, pillars, piers, posts and struts complete, all as specified and directed. 12 Material and labour forPCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in sub-base, foundations, floors paving etc complete, all as specified and directed. 13 Material and labour forcement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed 14 Material and labour forRCC1:2:4 (Nominal Mix) (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, chajjas facia of balconies, canopies, deck slabs and in shelves and the like complete, all as specified and directed. 15 Material and labour forbrick work with fly ash bricksstraight or curved on plan exc 6 Mtr mean radius built in CM (1:6) complete, all as specified and directed. 16 All as per Srl item No 15 here-in-before but in CM 1:4. 17 All as per Srl item No 15 here-in-before butinhalf brick thick walls built in CM 1:4 complete, all as specified and directed. 18 Material and labour forcuttingchases,pinningin brick walls for concealed water tubingn.exc 10cm girthand making good facing where requiredand pointingin CM 1:3complete, all as specified and directed. 19 Material and labour forcutting holes on brickwall in cement mortor for insertinghold fast and making good for dismantled portion in CM 1:3 or PCC 1:2:4 wall exc half brick but n.exc one brick thick complete, all as specified and directed. 20 Material and labour forgranite 20 mm thick over and including 10 mm thick CM 1:4 (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rubbing and polishing complete all as specified and as directed. 21 Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete, all as specified and directed. 22 Form work to flat soffits of suspended slabs such as roof slabs, floor slabs and lintels, landingand similar work n exc 200mm thick complete, all as specified and directed. 23 Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. complete, all as specified and directed. 24 Formwork to sides of pillars, posts, struts, piers,columns and stanchions complete, all as specified and directed. 25 Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete, all as specified and directed. 26 Taking down chowkats or frames n. exc 1.5 Sqm each (Without taking off shutters from the frame) complete, all as specified and directed. 27 Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame) complete, all as specified and directed. 28 Supply and fixing of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. 29 Supply and fixing ofsolid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specification & drawing. 30 Supply and fixing of aluminium anodised, barrel tower bolts of extruded sectionof length 150 mm and fixed with cadmium plated wood screws complete all as specified and directed. 31 Supply and fixing of 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete, all as specified and directed. 32 Supply and fixing of 150 mm aluminium handle cast type anodized complete, all as specified and directed. 33 Supply and fixing of tubular towel rail 20 mm dia 600 mm long brass CP including brackets fixed in repairs complete all as directed. 34 Supply and fixing of aluminium body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed. 35 Supply and fixing ofstainless steelwire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed. 36 Material and labour formild steel work as in wind ties for roof including securing bolts necessary drilling, bolting etc, complete all as specified and directed. 37 Material and labour for1 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete, all as specified and directed. 38 Material and labour for mild steel TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete, all as specified and directed. 39 Material and labour formild steel deformed TMT bars 5 mm to 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as spd and directed by Engr-in-Charge 40 Material and labour for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including hooks and hinges or steel hanging door fittings , fastening Fe-290(Grde-E165) and fixing complete, all as specified and directed. 41 Supply and fixing ofsteel work in tubular trusses including special shaped washer etccomplete using ERW or induction butt welded tubes conforming to I.S 1161-1979 St -240 complete all as specified and directed. 42 Supply and fixing ofsteel ventilator with top hung shutter includinghinges steel peg stay, complete as specified as directed. (Note:- The Glass/ wire gauze shall be measured and paid seperately. 43 Supply and fixing of powder coated aluminium anodisedframe for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified 44 Supply and fixing of powder coated aluminium anodised door shutters, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading screws etc incl sheet glass 5.5 mm thick ordinary qlty complete all as specified and directed. 45 Supply and fixing ofpowder coatedaluminium anodised window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long, hinges type B-21, 100mm long (2 no.) suitable handle incl sheet glass 4mm thick complete all as specified and directed. 46 Material and labour forpre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed. 47 Material and labour forpre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based plain steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed. 48 Material and labour forapplying one coat of aluminium paint @ 0.20 Kg Per Sqm over APP membrane, complete all as specified and directed. 49 Material and labour for water proofing treatment to roof slab with APP based modified polymeric membrane centre core 100mm micron outer flim 20 micron each having thickness 3 mm weight not less than 3kg/Sqm with 100mm overlap laid as per manuacturers instructions andcomplete all as specified and as directed by Engineer-in-Charge with following course of description below:-(a) 1st coat applying bitumen primer confirming to IS-3384-1965 @ 0.40 Kg/Sqm to be applied on prepared roof surface till the surface is properly impregnated(b) 2nd coat of bonding material using blown type bitumen conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm(c) 3rd course i.e laying of APP based modified membrane described herein before with 100mm overlap in longitudinal direction and 150mm in transverse direction, all joints and changes in all direction should be covered with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane all as directed. 50 Taking downeaves gutter and rain water pipes including all fittings any size and pattern complete, all as specified and directed. 51 Material and labour for75mm PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection and path laid in alternate panels not more than 3 mtr in length, laid to slope 1:30 finished even and smooth without using extra cement including forming joints 10 mm wide and upto full depth of PCC and filled with bitumen mastic (1:3), 1 part bitumen 85/25 and 3 parts of sand complete all as specified and directed. (Note:-Bitumen mastic will measured and paid seperately). 52 Material and labour for75 mm thick,PCC 1:4:8 type D2 using 40 mm graded stone aggreagateas in sub base of flooring complete all as directed. 53 Material and labour for25 mm thick cement concrete 1:2:4 type B0 (using 12.5mmgraded crushed stone aggreagate) as in flooring all as directed. 54 Material and labour forcoloured glazed ceramic tiles 300x 450 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to stepsetc., set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing screed in CM 1:4 on wall complete all as specified and directed. 55 Material and labour forjointless Non-skid coloured cermaic tiles 7 to 8mm thick (squre/rectanglar) are of each tiles 400mmX400mm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6, complete all as specified and directed 56 Material and labour forNon - skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6, complete all as specified and directed. 57 Machine pressed precast concrete interlocking paver blockwith grey cement and pignent any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed. 58 Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. 59 Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed. 60 Rendering 12 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces mixed with WPC as per menufacturers intructions, finished even and smoothwithout using extra cement complete all as specified and as directed. (Note: Water proofing compound shall be measured & paid separately). 61 Rendering5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed. 62 Material and labour for 15mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 finishedeven and smoothwithout using extra cement complete.all as sppecified and directed. 63 Material and labour for 15mm thick rendering other than fair faces of brick or concrete surfaces in CM 1:6 finishedeven and smoothwithout using extra cement complete, all as specified and directed. 64 Material and labour for 5mm thick renderingin CM 1:3 on ceilingof concrete surface finished even and fair etc. complete all as specified and directed 65 Preparing newly plastered surfaces of wall and applying two coats of oil bound distemberover 1 mm putty and a coat of chalk whitening primer preparatingto make the surface to be plain and smooth before primer complete all as sppecified and directed. 66 Complete removal of exisiting treatment, washing and rubbing of old distempered surfaces and applying two coats of oil bound distemberover over 1 mm putty and a coat of chalk whitening primer preparatory to distemering complete all as specified and as directed. 67 Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. 68 Material and labour forpreperation of new plastered surface and applying three coats of white wash on newly plastered surfaces of wall, complete all as directed. 69 Material and labour forpreparing new plastered surface of wall and applying two coats of cement based paint over and including a coat of cement based primer, complete all as specified and directed. 70 Material and labour forfor preparing newly plastered surfaces of ceiling and applying two coats of oil bound distemper overcoat of putty to make the surface to be plain and smooth complete all as specified and directed 71 Supply and fixing 4 mm thick pin headedglass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. 72 Material and labour forapplying two coats of synthetic enamel paint over and incl one coat of red oxide primer with and incl preparation of new surface of steel not exc 10 cm in width or girth, complete all as specified and directed. 73 Supply and fixingin repair 15 mm bore galvanized steel tubes, medium grade fixed to walls and ceilings or laid in floors complete all as specified and directed. 74 Supply and fixing in repair 20 mm bore galvanized steel tubes, medium grade fixed to walls and ceilings or laid in floors complete all as specified and directed. 75 Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store. 76 Dismantling water tank exc. 250 litres & not exc. 500 litres capacity of tanks complete all as specified and directed. 77 Supply and fixingrotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed. 78 Supply and fixingin repairs 15 mm bore bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. 79 Supply and fixing 15 mm bore bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. 80 Supply and fixingpillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, complete all specified and directed. 81 Supply and fixing in repair brass CP centre hole basin mixture 15 mm bore complete all as specified and directed. 82 Supply and fixingin repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as sppecified and directed. 83 Supply and fixing 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrulecomplete all as sppecified and directed. 84 Supply and fixing in repairs 15 mm bore concealed stop cock fancy type,chromium plated withlong shank and cup screwed down, screwed for iron pipe or for brass ferrule complete.all as sppecified and directed. 85 Supply and fixing in repairs 20 mm bore Gun-metal, ISI,globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 86 Supply and fixing in repairs 15 mm bore Gun-metal, ISI,globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 87 Supply and fixing in repair of 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed. 88 Supply and fixing in repair Vitreous China table top wash basin, white or off white, flat back, including single lever extended body basin mixer pillar tap, waste chain, plug, porcelain stopper, CP waste copling and CP bottle trap complete all as approved by Engr-in-charge and directed. 89 Supply and fixingin repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) white with grating, waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing arround urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe, urinal spreader complete all as specified and directed. 90 Supply and fixing chromium plated grating doom 100 mm dia with or without hole all as specified and directed 91 Supply and fixingin repair of PVC connection 450 long 15mm dia PTMT (PVC), complete all as directed. 92 Supply and fixing in repair PVC connections 15 mm size with PTMT nuts of length 600 mmcomplete all as specified and directed. 93 Supply and fixing stack clamps out of 50x5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof. 94 Supply and fixing PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors complete all as directed. 95 Supply and fixingPVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed. 96 Supply and fixing PVC (SWR) pipes 110mm dia in any length with rubber ring joint fixed to wall/floor complete all as specified and directed. 97 Supply and fixing PVC (SWR) pipes 75mm dia in any length with rubber ring joint fixed to wall/floor complete all as specified and directed. 98 Supply and fixing 110 mm bore PVC (SWR) bends with access door of any radius, complete all as specified and directed. 99 Supply and fixing 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed. 100 Supply and fixing 110 mm diaPVC (SWR)bendsany radius , complete all as specified and directed. 101 Supply and fixing 110 mm diaPVC (SWR)vent cowl, complete all as specified and directed. 102 Supply and fixing 110 mm bore PVC (SWR) junction single (Single `T) equal or unequal, complete all as specified and directed. 103 Supply and fixing75 mm bore PVC (SWR) junction single (Single `T) equal or unequal, complete all as specified and directed. 104 Supply and fixingPVC Nahani/ floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed. 105 Supply and fixing125/110 mm PVC (SWR) gully trap, setting and jointing with solvent cement 106 Material and labour for concrete bed to drain pipe for 150 mm dia pipes in PCC (1:4:8) type D2 (using 40 mm graded crushed stone aggregate) incl packing under and haunching against the sides of pipes after they are laid and tested. 107 Material and labour for 150mm reinforced concrete pipes, class NP2, laid and jointed with skeins of spun soaked in neat cement washer shall be inserted in the grooves at the ends of the pipes, the two adjoining pipes put against each other the collar is slipped over the joint covering equally both the pipes, more skiens of spun yarn soaked in cement wash shall be passed round the pipes and inserted in the joints by means of caulking tools after that cement mortar 1:2 slightly moistened shall be inserted in the joints finished in 45 degree slope complete Note:- After curing 7 days to the joints the sewage pipeshall be tested as per procedure laid down for water test as specified in SSR Part-I. 108 Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed. 109 Supply and fixing plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. 110 Supply and fixing viterous china squantting pan Orissa pattern size 580 x 440 mmwhite with P or Strap front or back inletand foot rest WCs (excluding flushing cistern and flush pipe) including provision of cement concrete bedding and making good surfaces complete all as directed. as specified. 111 Supply and fixingPVC low level flushing cistern 10 lts capacity with ball valve float and handle ,syphonic action type including brackets and flush pipe of polythelene of low or high density or PVC 32 mm dia low level flushing cistern fixed in repairs all as specified and directed. 112 Supply and fixingvitreous china wash hand basin ,white, flat back, size 550x400 mm including chain and plug and porcelain stopper, brackets including cutting for and pinning in ends of brackets or erecting stand 113 Supply and fixing for 600x450mm size and 6mm thick beveled edge looking mirror of selected quality glass, having PVC moulding/beading all around, mounted on 4mm thick PVC board, with and incl fixing accessories, complete all as specified and directed. 114 Demolition of brick/stone masonary built in cement mortar incl all quoins arches pillars etc complete. 115 Dismantling for stone slabs and tiles of any description or thickness in floors, aprons etc, laid dry and pointed in any mortar, complete all as specified and directed. 116 Demolition of cement concrete in ground floor including terrazo flooringand paving n exc 15cm thickness (below or above the ground level) built in cement mortar. Complete all as spd 117 Demolition of RCC not exc 15cm thickness roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work 118 Supply and fixing ofhand shower (health faucet) with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as directed. 119 Supply and fixing in repair SS towel rail 600mm Long fixed with and including chromium plated brass screws complete all as specified and directed. 120 Complete removal of exisiting treatment, washing and rubbing of old surfaces of wall and applying two coats of weather proof exterior grade emulsion over and includinga coat ofexterior grade cement based primer complete all as specified and directed. 121 Supply and fix aluminium anodised grill, 3 to 5 mm thick made in diamond shape mesh of size 65 x 65 mm complete as specified and directed. 122 Supply and fixing vitreous China wash down water closet pan One Piece EWC (pedestal sigle pattern), with smooth action plastic seat cover, valveless symphonic action dual type flushing cistern fixing as per manufacturing instruction complete as specified and directed. 123 Supply and fixing ofCP brass health faucet (hand shower) including flexible pipe of required lengthfixing to 15m dia pipe with brass check nut complete all as specifed and directed. 124 Supply and fixing ofexposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-paintednon asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed. 125 Supply and fixing of SS grating of square/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed. 126 Supply and fixing in repair of brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete, all as sppecified and directed. 127 M&L for preparing newly plastered surfaces ofnew wall and applying two coats of weather proof exterior grade emulsion over and including a coat of primer complete all as specified and directed. 128 Supply and fixing in repairs 15 mm bore bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as sppecified and directed. 129 Removal of excavated spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed. 130 Supply and laying fly ash brick for protection of cable laid in trenches for underground cable of compressive strength not less 75 Kg/Sqcm all as specified and directed. 131 Supply and fixing ofGI tubing , medium grade, galavanised with all fitting laid in trenches of size 20 mm bore complete all as specified and directed . 132 Supply and fixing ofGI tubing , medium grade, galavanised with all fitting laid in trenches of size 15 mm bore complete all as specified and directed . 133 Supply and fixing 1000 ltrs capacity, rotational moulded polythelene water storage tanks white (ISI marked) (three layer , cylindrical vertical with closed top) , hoisted and fixecd in position including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwd for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and as directed. 134 Supply and fixing stop valve cast copper alloy 15 mm dia screwed down high pressure with crutch or butter fly handle screwed both end for GI pipe complete all as specified and directed 135 Supply and fixing of PVC connection 15 mm dia , 400 mm length complete all as specified and directed. 136 Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in any type of soil complete all as specified and directed. 137 Material and labour forcement concrete in foundations, filling and mass concrete 1:3:6 type C2 (40 mm graded crushed stone aggregate) complete all as specified and directed. 138 Material and labour for PCC 1:2:4 type B-1 (using 12.5mm graded crushed stone aggregate) as kerbs, coping etc complete all as specified and directed. 139 Supply and fixing of MSposts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire etc ;angle, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or rivetting etc and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed by Engineer-In-Charge. 140 Mild steel screw or bolts (machine made) with hexoganal or square heads at one and screwed the other, or screwed both ends each screwed end to be filled with washers and hexogonal or square nut ,not exceeding5cm long and diameter of neck 5 to 10mm complete all as specified and directed 141 Material and labour for Mild steel round bar Gd E-250 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for columns hooking ends and binding with and including mild steel wire annealed not less tan 0.9 mm dia or securing with clips quality conforming to round bars confirming Fe-410-W(Gde.E-250), complete all as specified and as directed. 142 Material and labour for 15 mm thick cement plaster in cm 1:4as on other than fair face of brick or concrete surface finished surface even and fairall as specified and directed. 143 Supply and fixing 3 or 4mm dia pvc coated galvanised mild steel chain link fencing of mesh size 75 x 75mm fixed with string bolts complete all as specified and directed. 144 Supply and fixing of for mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 complete.all as sppecified and directed. 145 Removing excavated material exc 250m but not exc 500m and depositing where directed at a level not exc 1.5m above the starting point complete all as spcd and directed 146 Material and labour forgreen marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and dismantling of existing marble complete all as specified and directed. 147 Supply and fixing of aluminiumanodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed. 148 Supply and fixing of aluminium alloy, anodised, 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed. 149 Supply and fixing of aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed. 150 Supply and fixing of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. 151 Roof trusses Fe-290 Gde E-165 (framed), trussed, purlin, crane gentries,rails and fastenings and heavy bracket framing (beam, tee,angle, channel or flat section ms tube including distance pieces ,cleats etc all as spc.Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete.all as sppecified and directed. 152 Supply and fixing of pressed steel frames 1.25mm thick for door size of frame 105 X 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges and two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfacescomplete all as specified and directed. 153 Supply and fixing of Gl powder coated frame work for seamless false ceiling,size of grid 605 x 605mm with main tee of size 32mmx23.5mmx1.5mm thick, cross tee of size 25mmx23.5mmx1..28mm and angle of size 23.5mmx23.5mmx1.2mm fixed on wall all powder coated finish on exposed surface of tee and angle, hung from ceiling using 2mm dia GI suspension wires and J bolts , washers, nuts spaced at 1200mm both ways including making niches for fans/light all as specified and as directed. 154 Supply and fixing of 12mm thick perforated particle board/ tiles for insulation and accoustic purposes 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid complete all as specified and directed. 155 Supply and fixing hangers 6 mm diaGL (upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm, 60mm long and expansion hold fasteners 12.5mm dia 40 mm long including Anodised aluminium snap grid frame work for false ceiling complete,all as specified and directed. 156 Supply and fixing of machine cut kota stone slab flooring 20-22mm thick over cement screed base 20mm thick in 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including demolition existing complete all as specified and directed. 157 Material and labour for coloured chequered cement concrete tiles with grey cement and no pigment , 30cm x 30cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors in floors over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 158 Supply and fixing of for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to matchincluding 15 mm thick screed bed in CM 1:6 and dismantling of existing tile floor and screed complete all as specified. 159 Material and labour for 10mm thick cement plastering in cm 1:3 on ceiling for brick or concrete surfaces other than fair surface, finished the surfaces even and smooth without using extra cement built in cement mortar all as specified & directed. 160 Material and labour for preparation of new plaster surface and applying three coats of white wash on ceiling complete all as specified. 161 Material and labour forpreparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of primer complete all as specified and directed. 162 Supply and fixing of in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC trap, integral foot rest including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 using 40mm stone aggregate complete all as specified and directed. 163 Dismantling water tank 500 litres capacity of tanks, complete all as specified and directed. 164 Supply and fixing in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc complete, all as specified and directed. 165 Supply and fixingin repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm borecomplete all as specified and directed. 166 Supply and fixing of in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash fitting of wash basin and sink complete, all as specified and directed. 167 Supply and fixing of 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specifiwd and directed. 168 Supply and fixing of steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 complete incl two coat of painting: :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window(ii)Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii)MS Tower bolt 150mm long-02 Nos per leaf (iv)Z section 20mmX25mm,100mm long stopper -01 Nos per leaf(v)Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi)MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth, glass shall be measured and paid for separately. 169 Taking down old existing window/ ventilator and Supply and fixing of steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated)comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, painting with one shop coat of zinc chromate primer incl two coat of painting complete all as specified and directed. Note: Glass/ wire cloth shall be measured and paid for separately 170 Supply and fixing of 30 mm thickfactory made Flush shutters, solid core construction, with block board core and plywood face panels on both side complete all as specified and directed. 171 Labour for drilling hole under the road with the help of bocki/ manually or by machine for crossing GI tubing of any size for cable protection all as specified and directed by Engineer-in-Charge. 172 Material and labour forroad cutting including excavation returning filling spreading levellng well rammng in layers soling with broken boulders/ stones, WBM 7.5 cm thick coarse aggregate retrieved from dismantling the existing WBM of road, watering and ramming, 40 mm thick PCC 1:2:4 (using 20mm graded crushed stone aggregate) for road patch repair work, section/ cross section area of cutting shall be complete, all as specified and directed. 173 Use and waste of form work to chullah hoods, shelves, chajjas, weather shades, corbels, water troughs and similar items including edges rough finished surfaces of concrete complete, all as specified and directed. 174 Supply and fixing stand for desert cooler made of angle iron 50x50x6 mm in size including bracing supports, clamps and back plates fabricated from structural steel section including nuts, bolts, welding, bending cold or hot drilling bolt in any shape of size as indicated or directed and any including applying two coats of synethic enamel paint over a coat of rec oxide confirming to Fe-410W (Gde E-250) quality complete, all as specified and directed. 175 Point wiringwith PVC insulated and PVC sheathed single core multistrandedFRLSH copper conductor cable of size 1.5 Sqmm (nominal area) using approved colour coding, 1100 volts grade, ISI marked,including PVC conduit heavy grade, 20 mm or higher dia. with fittings concealed in wall/ on surface for ceiling with continuous earth wire of PVC insulated and PVC sheathed single core multistrandedFRLS copper conductor cable of size 1.5 Sqmm (nominal area) 1100 volts grade, ISI marked and connecting to the common earth dolly including provn of 3mm thick plastic laminated sheet of appropriate size and sunken CI/pressed steel terminal boxes for mounting switches,sockets and regulators etc.including cutting chases andmaking good to the disturbed surfaces as per existing for One light point/fan point/ bell point controlled by one, one way switch complete, all as specified and directed. 176 All as per Srl item No 175 here-in-before but for onesocket6Amultipin 2 module on independent board complete, all as specified and directed. 177 All as per Srl item No 175 here-in-before but one socket, 6A multipurposes 2 module on same board complete, all as specified and directed. 178 Material and labour for point wiring with stranded copper conductor 2.5 Sqmm (nominal area), single core, multistranded, FRLSH, PVC insulated and unsheathed cable 1100 volts grade, ISI marked drawn in and including heavy duty PVC concealed conduit with fittings ISI marked, terminated in junction box incl 2.5 Sqmm and connected to earth dolly modular boxes, modular plates, fixed with metal screw, for mounting switches/sockets and regulators complete all as specified and as directed. Note:- (i) Cutting chases for laying conduit and modular boxes, plates, brass screw, washer and making good to walls, roof , floor will be included in the above quoted rates.(ii) Modular boxes and Modular cover Plate will be measured and paid separately. 179 All as per item Ser No 178 here-in-before but one socket16Aon independent board complete, all as specified and directed. 180 Supply and fixing of switch piano flush type single pole one way 6 amps complete, all as specified and directed. 181 Supply and fixing modular switch 1 way 6A, 1 module complete all as specified and directed by Engr-in-Charge 182 Supply and fixing of switch flush type 15 amps single pole type one waycomplete, all as specified and directed. 183 Supply and fixing modular metal box flush type 6 module complete, all as specified and directed. 184 Supply and fixing modular metal box flush type 8 module complete all as specified and directed byEngr-in-Charge 185 Supply and fixing modular white cover plate with frame 8 module complete, all as specified and directed. 186 Supply and fixing of socket outlet 3 pin 15 amps flush type complete, all as specified and directed. 187 Supply and fixing of socket outlet 3 pin 6 amp flush type complete, all as specified and directed. 188 Supply and fixing switch socket combination flush type (multipurpose type) but 5A/16A, 5 in 1 15 Amps, 240V complete all as specified and directed 189 Supplying andfixing in repair sheet metalenclosure forDB’s when MCB’s to beused of 240 volt 8 way with 200 amps rated bus bar SPN doubledoorcomplete all asspecified anddirected. Note : All the connection of incoming and out goiing wire in MCB will be made with thimble with suitable size complete, all as specified and directed. 190 Material and labour for ceiling rose, surface bakelite three terminal/ phase PVC polycarbonate isolated body complete, all as specified and directed. 191 Taking down carefully ceilingfan with complete fittings at site removing fans and depositing in MES storeyardand re-fixing after completion of work at thesite complete with connecting cable and providing ceiling rose and set of canopy all as specified and directed. 192 Material and labour for submain wiring with two single core multi stranded PVC insulated unsheathedcopper conductor of grade 1100 VoltFRLS cable of size 2.5 sq mm (red forPhase and black for neutral) andincluding necessary fixing arrangement with wall/ roof in and including non-metallic rigid PVC conduit of suitable bore (as specified in SSR Part-I) and 2.5 sqmm multi stranded copper conductor FRLS cable PVC unsheathed (green coloured) for earthing with complete accessories duly connected with earth duly complete all as specified and directed. Note :- (a) 3 runs of cable and one run of PVC conduit will be measured as one unit i.e. one RM.(b) Cost of cutting chases and making good of disturbed surface etc.shall be deemed to be included in the quoted rate 193 Material and labour forsub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductorof grade 1100 Volt , FRLS cableof size 6 sqmm (red for phase and black for neutral)and including electrical grade PVC conduitsof desired colour not less than1.2 mm thick and 25 mm dia & 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth duly complete and taking down old unserviceable one.Note :- (a) Cost of making good the disturbed surface plastering/filling putty alongwith matching with the existing colour with MES Approvalmakeof distemper is deemed to be included in the quoted rate by contractor.(b) Three runof cable alongwith PVC conduit together shall be measured as single run. 194 Supply & installing water cooler electric driven (single phase) fully stainless steel storage capacityhaving approx 80 ltr and nominal cooling capacity 40 ltr per hour including plateform & suitable drainage arrangementfor waste water. complete all as specified. 195 Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades,frame andlouvers, Including making suitable hole in wall all as directed at site. 196 Supply and fix fresh air fan 250mm size including making of hole/openingin wallcomplete all as specified and directed by Engr-in-charge. 197 Supply and fixing ofin repair MCBsinglepole 6amps to 32 amps complete all asspecified anddirected. 198 All as per Ser item No 197 abovehere-in-before but singlepoleand neutral 32 amps ,complete all asspecified anddirected. 199 Supply and fixing in repair indoor type decorative recess mounted direct/indrect 2x2 lumanaries light fixures made up to 36 watt LED netural white complete including making connection with twin core twisted flexible copper conductor cable with suitable size complete, all as specified and directed. 200 Supply, installation and fix refrigerator 200 ltr gross capacity,electric driven, single phase, frost free, stabilizer free operation, with automatic digital inverter technology easy clean back feature with safty cover at back for safty of internal vital components such as condenser coil, capillary tube, compressor etc with environment friendly R 134a refrigerant. The refrigerator should have two separate shelves each for freezer and general cooling area, complete with all standard accessories as per manufacturers instruction complete all as specified and directed. 201 Supply, installation, commissioning of metal top deep freezer single phase 240 volt, 50 hz 300 ltr capacity complete, all as specified and directed. 202 Supply and fixing evaporative desert cooler electric driven (single phase) of capacity 5000 cum/hr steel 1500 RPM 230 volt body made out of sheet 18SWG for main body and 22 SWG for side covers duly super enamelled painted with two coats of hammer tone paint Ist quality over a coat of red oxide primer complete inner and outer sides with front grill made out of steel (heavy duty) propeller cooler fan (aluminum blades) 500mm sweep dia with heavy duty motor,AC single phase 230 Volts,50c/s,copper wound with submersible pump& including float valve complete all as specified. 203 Supply & fixing LED light fitting mirror type with high out put diffuser 2 feet, 08 watt / 10 watt 220 V AC decorative type with driver holder including LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 204 Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete with fittings such as switches. Ceiling roses, pendents, Regulator Socket etc completeat site and making goods disturbed surfaces of walls, floors etc. 205 Supply and fixing of in replacement offan regulatorelectronic type 5 step100watt,240 Volt and connectingcomplete allas specifiedand directed all as directed. 206 Supply and fixing of surface mounting universal batten housing made of powder coated CRCA sheet fixed suitable for upto 1 x 18/20 W LED tube rodall as directed 207 Supply and fixing of LED tube light 20W ultra bright LED polycarbonate tubelight with very high efficacy suitable for fitting intotube light batten fittingt all as directed 208 Supply and fixing of lamp holder PVC body angle type including 9 watt LED bulb polycarbonate body complete all as specified and directed. 209 Supply andlayingcable XLPE insulated screened PVC bedded, galvanisedsteel strip or wire ,armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminiumconductor of size 35 Sqmm 3.5 core complete all as specified and directed. 210 Material and labour forpre - fabricated LT panel boardout door type with CRCA sheet thickness not less than 3.15mm dust, moisture and vermin proof provision of front and rear opening including 100 Amp ratedaluminium bus bar prewired including the following and necessary PCC foundation, angle iron frame (40x40x6mm), grouding on foundation to fix the panel board all as per standard specifications and CPRI approved complete, all as specified and directed.(a) MCCB 63 Amp 4 pole 15 KA , 50 Hz -01 No (Incoming) (b) MCCB 63 Amp DP , 10 KA , 50Hz- 01 Nos (Outgoing)(c) Volt meter 0-500 volts with selector switch digital type - 01 No(d) Ampere meter 0-100 Amp with CTs and selector switch digital type -01 No(e)Indictor lamp Red , yellow and green LED type- 01 Set(f) Onload changover of capacity 63 Amps 211 Material and labour for earthing complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25meters below ground level with top edge of the earth plate at a depth not less than 1.5 meter below the ground level, earth plate surrounded with 15cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same,GI plate connected with galvanised steel strip of size 25x4 mm by means of GI nuts, bolts and washers, Strip laid in 32mm dia light grade GI pipe as protection from top of the plate up to test point (cost of protection pipe up to 7.5 meters from earth electrode will be included in the rates quoted by the contractor) including following:-(a) Test point GI strip of size 25x4mm.(b) Watering pipe GI Mediumgrade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit.(GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c)Concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, exposed surfaces smoothlyfinished with 15mm thick cement mortar 1:6 plaster all as specified and directed. 212 Material and labour forcable protection GI tubing light grade fixed along the pole/ under road/ along the wall of size 40 mm bore with necessary clamps all as directed 213 A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender.The Schedule of Credit is pre-priced by MES.The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 22,132/- from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.
