Armo Works At Fsd Ujjain Fsd Ratlam And Fsd Meghnagar For The Year 2025 26. S.H Monsoon Repairs, Greasing Of Shutters And Other Misc, Works.; 1 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 125.00 54.65 sqm 6831.25 2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 125.00 333.35 sqm 41668.75 3 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 2180.00 19.75 sqm 43055.00 4 Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litres/10 sqm). 2180.00 160.60 sqm 350108.00 5 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. 180.00 102.80 sqm 18504.00 6 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Of any mix 68.00 2434.25 Cum 165529.00 7 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and 27.00 1520.10 sqm 41042.70 other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I 8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 46.62 6812.00 cum 317575.44 9 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 50 mm thick 470.00 768.63 sqm 361256.10 with 20 mm nominal size stone aggregate 10 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate 80.00 614.20 sqm 49136.00 11 Supplying, installation, testing & commissioning of Turbo ventilators of size 22 in stainless steel 430 grade with appropriate weight 4.85 kg having CFM 7KM per hour,2440 with blade length 360mm wing of 80mm , outer wings 22- 24 nos, inner wings 22-6 nos with self lubricating bearing etc complete as per manufacturers specification and stainless steel base plate etc as per direction of engineer in charge including the cutting of existing pre coated sheet. 18.00 6630.7 each 119352.60 12 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase 272.50 305.15 m 83153.38 13 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :For fixed portion: Anodised Aluminium (anodised transparent or dyed to required shade 59.00 495.05 kg 29207.95 according to IS 1868 minimum anodic coating of grade AC15) 14 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :For shutters: of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Anodised Aluminium (anodised transparent or dyed to required shade according to IS 1868 minimum anodic coating of grade AC15) 61.00 598.60 kg 36514.60 15 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10 kg/sqm) 8.00 1176.80 sqm 9414.40 16 Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) 3.00 1090.65 sqm 3271.95 17 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12.00 1139.30 sqm 13671.60 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side 18 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in substructure upto plinth level in all shapes and sizes in :Cement Mortar 1:6 (1 cement : 6 coarse sand). 18.00 6088.65 cum 109595.70 19 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 671.00 107.85 kg 72367.35 20 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 12.30 9045.75 cum 111262.73 21 Providing and fixing 15 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm 35.00 3684.39 sqm 128953.65 22 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with 1676.00 194.40 kg 325814.40 special shaped washers etc. complete. Hot finished welded type tubes. 23 Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-incharge) 0.50 mm (+0.05%) total coated thickness with Zinc coating 120grams per sqm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 249.00 710.45 sqm 176902.05 24 Supply of weather silicone sealant of make Dr.Fixit (1 Cartridge = 280 ml) for applying over Self drilling / Self tapping Screws as per directions of Engineer-in- charge. 50.00 327.20 Each 16360.00 25 Supply of 80x0.90 mm laths for rolling shutters at site as directed by Engineer-in-charge rate including all taxes, transport etc. 16.32 2015.90 sqm 32899.49 26 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineerin-charge, beyond 50 m initial lead, for all leads including all lifts involved 90.00 263.95 cum 23755.50 27 Lettering with black Japan paint of approved brand and manufacture 27335.00 6.15 1 letter of 1 cm height 168110.25 28 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side 26.00 532.35 metre 13841.10 of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm). 29 Labour charge for applying weather silicon sealant over Self drilling / Self tapping Screws including providing safety measures for the labourers to work at higher elevation viz., ropes etc., insurance coverage for labourers and hiring of required T&P etc complete. 3100.00 7.15 Sqm 22165.00 30 Supplying and fixing of Super flash strip 1.5mm thick and 10 metre in length of make STP ltd as per directions of Engineer in- charge. 10.00 375.90 Each 3759.00 31 Supply of self adhesive high performance water proofing (Supertene) strip of 1.5 mm thickness of SBS modified membrane of make STP ltd in rolls of 20.0mx1.0m as per directions of Engineer in- charge. 180.00 490.80 Each 88344.00 32 Laying Supertene over roofs including preparation of surface and providing necessary safety measures for the labourers to work at higher elevation, ropes etc., insurance coverage for labourers and hiring of requiring T&P etc complete but excluding grading.as per directions of Engineer in- charge. 180.00 206.85 Sqm 37233.00 33 Servicing to the rolling shutters including cleaning the side guides , springs and shaft etc., with kerosene oil, providing and applying fresh grease, applying tension to the springs replacing damaged parts and welding locking plates stoppers etc., wherever necessary etc complete as directed by the Engineer -inCharge(Rolling shutters parts, laths, springs etc. will be supplied at free of cost) 70.00 810.00 Each 56700.00 34 Supplying rolling shutter springs of 27.5 cm long wire spring grade no.2 for rolling shutters as per directions of Engineer in- charge. 22.00 469.45 Each 10327.90 35 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus 14.00 260.30 cum 3644.20 excavated soil as directed, within a lead of 50 m. All kinds of soil. 36 Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in 240 MPa steel grade, 5- 7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Flashings/ Aprons 58.00 809.35 Sqm 46942.30 37 Cleaning of Storm water drains in all depths and width 0.60m to 1.00m including removal of debris/ rubbish and disposal of the same in all leads and lifts filling in low lying areas and levelling complete in the depot premises as directed by the Engineer-in-charge and the drain to be kept clean during the period of contract. 620.00 85.35 Metre 52917.00 38 Cleaning of Service drains around godowns in all depths and width 0.30m including removal of debris/ rubbish and disposal of the same in all leads and lifts filling in low lying areas and levelling complete in the depot premises as directed by the Engineer-in-charge and the drain to be kept clean during the period of contract. 200.00 28.45 Metre 5690.00 39 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :600 mm dia. R.C.C. pipe 6.00 2243.4 Metre 13460.40 40 Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge 250.00 3.85 kg 962.50 41 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 1.82 3551.25 cum 6463.28 42 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 895.00 172.60 kg 154477.00 43 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 50.00 155.90 sqm 7795.00 44 Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral cores and wiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoro polymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. for all heights and all levels all complete as per the directions of Engineer-in-charge. 81.00 2661.70 sqm 215597.70 45 Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-inCharge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. 120.00 414.30 kg 49716.00 46 Providing, designing and fixing of Vinyl film of 120 microns thick of approved brand and manufacture on existing ACP surface at all heights and levels including design of 16.00 1351.50 sqm 21624.00 letters/symbols, colour, lamination etc. all complete as per directions of Engineer-incharge. 47 Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge. 1250.00 3.85 kg 4812.50 48 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below 31.00 367.20 each 11383.20 49 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below 25.20 2060.20 cum 51917.04 50 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 16.00 3551.25 cum 56820.00 51 Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge 36.00 2458.95 cum 88522.20 52 Credit for taking away dismantled steel obtained from dismantling RCC and dismantling of steel structures after proper stacking for weighment purpose and then taking away out of the depot complex as per the direction of Engineer in charge 2100.00 (-)38.80 kg (-)81480.00 53 Credit for taking away old bricks obtained from dismantling after proper stacking for counting purpose and then taking away out of the depot complex as per the direction of Engineer in charge 4669.00 (-) 2.67 each (-) 12466.23 54 Credit for taking away dismantled wooden windows, doors including chowkhats etc. after proper stacking for counting purpose and then taking away out of the depot complex as per 33.00 (-)151.60 each (-) 5002.80 the direction of Engineer in charge 55 Credit for taking away random rubble stone AS IS WHERE IS BASIS including loading, unloading& transportation etc. complete and as directed by Engineer-in-Charge. 25.00 (-)849.00 cum (-)21225.00 56 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineerin-charge, beyond 50 m initial lead, for all leads including all lifts involved 46.00 263.95 cum 12141.70
