Work Of Refurbishment And Repairing Of The Various Amenities For Aesthetic Up-Gradation Of The Workstations At Wdc.- 1 Replacement of damaged aluminum ceiling by dismantling & removing the existing ceiling along with carrier and providing the new aluminum linear metal ceiling 2 Ceiling fan of 1400 mm sweep with all accessories including Electronic Regulator for completing installation 3 Fixing of Ceiling fans Upto 0.5 Mtr 4 INDOOR LED FIXTURES - -LED Square Recessed Downlighter36W (600X600) 5 LED Tubelight fixtures 1X 18W 6 Wiring for submains- casing n cap -2 X 1.5 sq. mm+ 1 X 1.5 sq. mm earth wire in 20 x 12 mm(1/2 in.) 7 Light /Fan / Ex. fan Points 8 32A DP MCB 9 25 mm X 12 mm - Casing-Capping 10 50 x 50 x 6 mm of M.S.angle. 11 Removing any type of flooring i.e.mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles in flooring including bedding brick bat coba , paver blocks of any thickness etc in open passage, footpath, or any flooring laid on ground mechanically or manually and delivering materials in Ward Office and carting away unserviceable materials. 12 Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos sheet 13 Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. -Using rough kota stone of size 550 mm x 850 mm 14 M-20 grade plain cement concrete (cement content considered @ 260 kg/cum) 15 Providing and laying 600 x 600 x 8 mm thk. vitrified tiles as specified below conforming to I.S.15622- 2006 with water absorbtion less than 0.08% for flooring of an approved, quality, make and pattern /design for flooring including cement mortar bedding of 25 mm thick in 1:4 proportion, cutting, leveling, jointing, filling the joints by neat cement slurry or approved colour grout, curing, finishing etc complete as directed by Engineer In Charge. Light coloured glazed vitrified tiles 16 Providing laying and fixing glass mosaic tiles in the wet areas like swiming pool, toilets etc. of approved make, colour, pattern, size and thickness on the surface treated with waterproffing compound including backing coat of approved latex-modified thinset, jointing, filling the joints with non shrink neat cementetious coloured grout, curing, ponding, finishing etc. complete as per manufacturers specifications and as directed by Engineer-in-charge. 17 Ruby red, jet black, hasan green Granite for height upto 300 mm 18 Providing and fixing structural Profile decking sheet as per particular specification,with GI sheet, zinc coating not less than 275 GSM as per IS 277 and of yield strength 500 Mpa of approved make with specified Base Metal Thickness. The profile shall be structural decking profile having ribs & pitch as per the drawing referred with the embossments (shear groove) on top and side of the ribs for better composite action. The decking sheet shall be fabricated to required form as per the slab design and fixed with Galvanised Iron fasteners, self drilling screws, shear studs as per IS 1367, connectors etc. complete as per design, drawing and direction of Engineer-inCharge. (Refer typical drwg).The sheet shall be filled with 75mm thick M25 grade concrete reinforced with 8mm dia. HYSD bars placed 150mm C/C both ways. Plan area of the sheeting shall be measured and paid. Structural steel frame work shall be paid seperately. 19 Providing and applying synthetic enamel paint or flat oil paint in any requiered shade in 3 coats over a primer coat as per manufacturers specifications including scrapping, cleaning the surface etc. Complete. 20 Providing and applying first single coat of approved primer and two coats of synthetic enamel paint/flat oil paint of an approved make and colour as per manufacturers specifications to the metal purlins not more the 150mm in height, at all height and locations as directed including removing the existing paint by burning, cleaning, preparing the surface for painting etc. complete as directed by Engineer-in-charge 21 Providing and fixing wall paper / Graphic for highlighting the walls with proper adhesive in line level for reception, conference& Auditorium rooms and wherever required as per the drawings.Basic rate of Wall paper is Rs..100/- per Sft. Make - Ddecor / Nilaya By Asian Paints or equivalent. 22 Removing existing door or windows with frame and shutters and making good etc. to the existing surface. 23 Providing & fixing in position single leaf flush door of required sizefor internal doors of residential units, shutters madeof 45mm thickmarine grade block board core with 25mm x 45mm T.W. lippingpatti, 1mm thick approved decorative laminates finish on both faces ofshutter, including providing & fixing T.W. frame of 60mm x 150mm size,coating all the exposed surfaces of wood with 2 coats of flat enamel paint of approved shade & make over one coat of approvedsynthetic primer, coating all the surfaces of wood in contact withmasonary with Tar (Black Japan), preparing the surfaces, providing and fixing brass chrome finished or S.S. fittings and fastenings etc complete as per detailed drawing no. WD-26 & as directed by theEngineer in charge. D5,D7,D12,D8,D9,GL-D. 24 Removing and refixing Door frame along with shutters 25 Providing & fixing of Door Hinges 26 Providing & fixing of Door Handle 27 Removal of existing flushing cistern with all fittings at any height with making surface good and depositing all materials to Muncipal Store etc. complete as directed. 28 W.C. pan with ISI marked white solid plastic seat and lid 29 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete 30 Providing & fixing in position Jacquar Continental make CP Jet Spray with flexible CP supply pipe, and all other accessories, complete 31 Providing & fixing 2-way Bib cock JAQUAR MAKE, ORNAMIX Model No. 10041etc. complete.
