Tender For provision Of Certain Sanctioned Work Under Age B/R Beas Under Ge Kapurthala. - 1 Dismantling of asbestos cement (corrugated, semi-corrugated, etc) sheets in roof coverings including ridges, complete all as specified and directed. 2 Dismantling taking down framed trusses of span not exceeding 10m, complete all as specified and directed. 3 Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. 4 Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed. 5 S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. 6 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. 7 Erection and fixing only steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240. Complete all as specified and directed. 8 Erection and fixing only steel tubular work as in purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240. Complete all as specified and directed. 9 S&F rolled mild steel Fe 10-W (Gde-E-250) quality-A in Joist, channel, angle,tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed. 10 S&F steel tubular work as in purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. 11 M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed. 12 M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed. 13 M&L for cleaning ofSWT slit sludge/algie/vegitation and solid sludge up to the bottom of any size including removing complete all as specified and directed. 14 Demolition of brickwork/ stone masonrybuilt in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 15 M&L for brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 meter mean radius built in cement sand mortar 1:4 complete all as specified and directed. 16 Ditto all as per item No 15 above but except bricks complete all as specified and directed. 17 M&L for brick work with sub class size B bricks, straight or curved on plan, exc 6m mean radius, built in cement mortar 1:4 complete all as specified and as directed. 18 Taking down cement or cement lime plaster, any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. 19 M&L for 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces including finishing top surfaces even & fair without using extra cement complete all as specified and as directed. 20 M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls finished even and smooth, complete all as specified and directed. 21 M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls finished even and fair, complete all as specified and directed. 22 M&L for preparation of newly plastered surface of walls and applying two coats of Oil Bound Distemper over a coat of primer complete all as specified and directed. 23 M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed. 24 M&L for applying one coat of wall care putty not more than 2mm thick complete all as specified and directed. 25 Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. 26 M&L for Plain Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregates) in mass concrete, flooring and finishing the surfaces even & smooth with using extra cement with water proofing compound @ 3% by weight of cement complete all as specified and directed. (Note:- Liquid water proofing compound shall be measured andpaid for separately). 27 M&L for plain cement concrete (1:2:4), type B-2 (using 40 mm graded stone aggregates) as in road concrete etc complete al as specified and directed. 28 M&L for plain cement concrete Type B-1, 1:2:4 (20 mm graded crushed stone aggregate) as in copings, benching, haunching, bond stones bed and the like including use of necessary form work complete all as specified and directed. 29 M&Lfor providing reinforced cement concrete cast in situ Type B-1, 1:2:4 ( 20 mm graded stone aggregate) as in lintels upto 1.5m clear span including necessary formwork complete all as specified and directed. Note : Reinforcement shall be measured and paid separately. 30 M&L for use and waste of formwork to faces of walls, retaining walls, abetments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc. vertical or to batter and fair finished surface complete all as specified and directed. 31 M&L for 100mm thick, plain cement concrete 1:2:4, type B2 (using 40 mm graded stone aggregates) as in floor and finishing the surfaces even & smooth with using extra cement complete all as specified and as directed. 32 Supply only integral water proofing compound complete all as specified and as directed. 33 M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and directed. 34 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and directed. 35 M&L for 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough complete all as specified and directed. 36 M&L for Non-skid Ceramic joint free tiles 7 to 8 mm thick coloured/wooden finish (square/ rectangular)area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed. 37 M&L for Glazed coloured ceramic tile 450 x 300 x 7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified. 38 M&L for light shade Vitrified ceramic tiles 10mm thick (square/rectangular) polished ,area of each tiles not exceeding 0.36sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with 15mm thick screed bed (1:4) complete all as specified and directed. 39 M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in skirting/dado etc. over and including 10 mm thick plaster in cement and sand mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, complete all as specified and directed. 40 M&L for Machine Cut Kota Stone slab flooring for cooking platform and flooring 20-25 mm thick laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing bedded on 15mm thick bedding layer in CM 1:6 incl making hole for gas pipe, complete all as specified and directed. 41 M&L for Machine Cut Kota Stone as in risers, steps, skirting, dado, 20-25 thick laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing bedded on 15mm thick bedding layer in CM 1:6 incl making hole for gas pipe, complete all as specified and directed. 42 Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 43 M&L for Reinforced cement concrete 1:2:4 typeB-1 (using 20 mm graded stone aggregates) as in slab ofseptic tank, soak well, etc supported on walls, beams & columns in floors, roofs, landings, balconies, canopies, deck slabs & in shelves &the like etc complete all as specified and directed. 44 S&F for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 45 -Ditto- all as per item No 44above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders. Complete all as specified and directed. 46 Use and waste of formwork with fair finished flat concrete surfaces such as soffits of suspended slab, such as roof slabs, floor slabs, landings & similar work, n exc 200mm thick, horizontal or sloping complete all as specified and directed. 47 Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of area not exceeding 1.5Sqm each and removing from site complete all as specified and directed. 48 Taking down chowkhats or frameswith shutters (without taking off shutters from the frames) of area exceeding 1.5 sqm and not exceeding 4.00 sqm each and removing from site complete all as specified and directed. 49 S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification, complete all as specified and directed. 50 S&F for Factory made solid panel PVC door shutter 30 mm thick both side pre laminated with wood grain/coloured (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of same colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. 51 S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles ofz section 100mm long (c) Stopper - 01 No per leaf (d)Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f)Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3.Note:- Glass and painting shall be measured and paid separately under appropriate item etc, complete all as specified and directed. 52 S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm,single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles ofz section 20mm x 100mm long (c) Stopper - 01 No per leaf (d)Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note:- Wire mesh and painting shall be measured and paid separately under appropriate item etc, complete all as specified and directed. 53 S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 54 S&F for 150mm long, aluminum anodised, barrel tower bolts, of extruded section ISI marked complete all as specified. 55 S&F for Aluminum handles cast type anodised of size 150mm long ISI marked complete all as specified. 56 S&F in repair for 20 mm bore stainless steel curtain rod with 1 mm thick wall thickness and each length not more than 1.5 Meter including a pair of brackets and knobs with each length/ piece, fixed on doors and windows opening for hanging curtains complete all as specified and directed. 57 S&F galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified. 58 M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and priming with redoxide zinc chrome and painting with two coats of synthetic enamel paint complete all as specified and directed. 59 S&F for 4.00mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed. 60 M&L for ceiling using 9mm thick gypsum based ceiling tiles with weather resistance face on back side and vinyl finish including framework on the front fixed in 24mm GI Armstrong frame work of grid 600x600 mm size, the members of snap grid frame work of GI/Steel section of 24mm wide with T-flanges, channels etc of white colour having rotary stitching on all members, i.e main runner, 1200x600mm cross tee galvanised with minimum thickness of 120 gms per/sqm passed through 500 hrs test and hanging the same with existing roof members such as rafters, purlins or other wooden members particularly provided for hanging purpose using 8mm dia mild steel bar of required length fixed with nut bolt of 50mm long and 10mm dia of neck with washer flat iron 50x6mm thick clamps etc to steel members, complete all as specified and directed. 61 S&F Stainless Steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with SS wire staples complete all as specified & directed. 62 S&F 5.50mm thick sheet glass but exc 0.5 Sqm in each , ordinary quality and glazing with beads fixed with metal panel pins with solar control dil 25micron reflective type sicked to glass panes as per instruction of manufacturers complete all as specified and directed. 63 S&F floor door stopper 140mm of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor all as specified and directed. 64 S&F, 200 mm size, aluminium anodised, barrel tower bolts of extruded section & fixed completeall as specified and as directed. 65 S&F Vitreous China Urinal, Half stall type, white (including coupling and waste pipe complete all as specified and directed. 66 S&F urinal spreader of PTMT any colour for fixing with 15mm dia pipe (min weight 60gms) complete all as specified and as directed. 67 S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified. 68 S&Fvitreous chinawash hand basin oval type, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc with pedestal complete all as specified and directed. 69 S&F for 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 70 S&F sheet glass shelf PTMT assembly consisting of 5.5mm thick sheet glass shelf 12cm wide fixedwith including chromium plated screw, bracket guard and railing 60cm long complete all as specified and directed. 71 S&F stainless steel soap dish complete all as specified and directed. 72 S&F Tubular towel rail Brass Chromium plated, D types, 60cm long between flanges complete all as specified and directed. 73 S&F in repair 15mm bore bib taps, cast copper alloy with crutch , chromium plated, fancy type, screwed down, screwed for iron pipe and fixed, complete all as specified and directed. 74 S&F in repair 15mm bore Stop Valve/angle valve, cast copper alloy with crutch, chromium plated,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or fpr unions and fixed, complete all as specified and directed. 75 S&F for floor grating 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed. 76 S&F in repair for PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed. 77 Taking up or down, steel tubing 15mm bore and connections including cleaning for re-fixing and removal from site complete all as specified and as directed. 78 S&F 15mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floors complete all as specified and directed. 79 Taking up or down, steel tubing 20mm bore and connections including cleaning for re-fixing and removal from site complete all as specified and as directed. 80 S&F 20mm bore galvanized steel water tubing, medium grade with all fittings fixed to wall, ceiling or laid in floors complete all as specified and directed. 81 M&L for RCC NP2 pipe 150mm dia bore and jointed complete with collars as in culvert complete all as specified and directed. 82 M&L for cement concrete (1:3:6,type C2) bed to drain pipes of 150mm bore dia including packing under and haunching against the sides of pipes after they are laid and tested all as specified and directed. 83 Excavation in trenches, not exceeding 1.5 mtr wide& not exceeding 1.5 mtr depth for foundation, or for shafts, wells, casspits, manholes, pier holes, laying of cables etc not exceeding 10 sqm on plan &and getting out in soft and loose soil complete all as specified and directed. 84 Returning, filling in, including spreading, leveling, watering and well ramming the approved soil/earth in layers not exceeding 25cm thick in any type of soil complete all as specified and directed. 85 M&L for removing excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified & directed. 86 M&L for pre-construction anti termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. 87 S&F for PVC (SWR) P Trap 110mm, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. 88 S&F for PVC (SWR) gully Trap 125/110mm, setting and jointing with solvent cement, complete all as specified and directed. 89 S&F rotational moulded polyethylene (Three layered) water storage tanks 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified including 20mm dia ball brass valve, complete all as specified and directed. 90 S&F for gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to steel pipe or union, 20mm bore dia of pipe complete all as specified and directed. 91 S&F in repair for 110mm bore PVC (SWR) pipes single sockets in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. 92 S&F for 110 mm bore PVC (SWR) bend any radius complete all as specified and directed. 93 S&F for 110mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed. 94 Excavation in post holes (or similar holes ) each not exceeding 0.50 Cum,and getting out,returning filing in and ramming earth with broken rubble mixed with earth around in layers not exceeding 25cm,watering etc and removing surplus soil not exceeding 50m and making good surface in loose/soft soil, complete all as specified and directed. 95 S&F mild steel works as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc including all necessary drilling, bolting or riveting flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 96 M&L for framed work as in post of parking shed, perline, doors or gates and chowkhats of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening conforming to Gde Fe 290 (Gde E-165) complete all as specified and directed. 97 Supply only GI chain link fencing of any size or type, complete all as specified and directed . 98 Fixing only GI chain link fencing of any size or typeincluding line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire, complete all as specified and directed. 99 S&F galvanized. 2 strand, steel barbedwire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire with staples or steel, complete all as specified and directed. 100 M&L for mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed. 101 S&F for 40 mm thick Factory made Flush shutters, solid core construction with block board core and both face of shutter should be covered with coloured veneer plywood and incl 10mm glass of size 0.60m x 0.90 m in the centre of door shutter, supplied and fixed complete all as specified and directed. 102 S&F 2nd class hard wood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified. 103 S&F for powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc with a minimum size of 101 x 45 mm to carry laod of Aluminium Door/ windows as fixed complete all as specified and directed. 104 S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and as directed. 105 S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised complete all as specified and as directed. 106 S&F powder coated anodised aluminium fly proof window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading complete all as specified and as directed. 107 S&F aluminium diamond grill security window with flyscreens, average width of aperture 75mm, premium quality security window with 20mm frame (thickness) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading etc complete all as specified and as directed. 108 Hacking out old broken glass (anythickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified and directed. 109 Supply only 4mm thick sheet glass, ordinary quality and glazing with oil putty in squareexceeding 0.5 sqm in each pane, complete all as specified and directed. 110 Supply only 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane, complete all as specified and directed. 111 S&F 4mm thick figured glass pin head type and glazing with oil putty in square exc 0.50sqm in each pane complete all as specified and directed. 112 S&F 4mm thick figured glass pin head type and glazing with oil putty in squarenot exc 0.50 sqm in each pane complete all as specified and directed. 113 S&F for 300mm Aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified. 114 S&F for Stainless steel butt hinges, 100 mm long medium weight, complete all as specified. 115 S&F 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed. 116 S&F for door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed complete all as specified and directed. 117 S&F for aluminium mortice lock of 2 levers, vertical type, size 100mm complete all as specified and as directed. 118 S&F in repair for stainless steel wire cloth, 0.36mm nominal dia of wire and average average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 119 Taking down GI pipe 50mm bore medium grade and fitting and S&F GI tubing medium grade 50 mm bore in any length with all fitting laid in trench and connecting up with water supply main complete all as specified and directed.Note : Excavation and earthwork shall be measured and paid for separetely under approprite item. 120 Taking down old unserviceable GI/CI pipe 80 mm bore and supply, laying, jointing and testing new cast iron pipe 80 mm bore centrifugally cast class LA confirming to IS - 1536 spigot and socketed ends in any length laid in trenches complete all as specified and directed.(Note : excavation, earth work, CI fitting and new run lead joint Rubber gasketJoint shall be measured and paid for separetely under appropriate item of Sch A) 121 All as per item No 120 above here in before but 150 mm bore complete all as specified and directed. 122 S&F in replacment of gun metal globe or gate valve with iron wheel head screwed both ends suitable for galvanised iron pipe of 50mm bore complete all as specified and as directed. 123 S&F in replacement cast iron fitting Suitable for CI/DI Pipes such as bends, tapers, (any type, radius and angle) tapers any type, (straight, bend, increasing,decreasing or double socket etc.)Tee pieces single branch. Y junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs tee pieces, single branch for spigot and socket and flanged pipe up to 150 mm bore complete all as specified and directed. 124 Taking down carefully aluminium / copper point wiring (light, fan, socket, powerpoint) including batten, conduit and fittings such as switches, ceiling rose, sockets, brackets, light fittings, switch board etc, making good distrubed surfaces of wall, floar, ceiling etc complete all as specified and directed. 125 M&L for point wiring for one light / fan / bell point with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor ( FRLS ) 1100 Volts grade cable ( red colour cable to be used for live connection and black colour cable to be used for neutral connection ) controlled by one way switch drown through and including PVC concealed conduit with all accessories including 1.5 sqmm copper multistrand conductor (FRLS ) 1100 Volts grade unsheathed PVC insulated ( green colour ) continuity earth wire connected to common earth dolly and sunk cast pressed steel Metal flush mounting box for mounting of fittings like switch , socket and fan regulator and cover plat of suitable modules capacity and make of swich socket complete all as specified and as directed. 126 (a) One light point controlled by one, one way switch 127 (b)One fan point controlled by one, one way switch 128 (c)One socket outlet 3 Pin, 5 Amp on independent board 129 (d) One socket outlet 3 Pin, 5 Amp on same board. 130 All as per item No 125 here in before but 2.5 Sqmm P.V.C insulated unsheathed cable with stranded copper conductor for 6 pin 6/16 Amp switch socket combination on independent board complete all as specified and as directed. 131 S&F switch piano flush type single pole one way 6 Amp (ISI Marked) complete all as specified and directed. 132 S&F switch piano flush type single pole one way 15 Amp (ISI Marked) complete all as specified and as directed. 133 S&F socket out let 2 in 1, 3 pin 5 Ampflush type (ISI Marked) complete all as specified and as directed. 134 S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked) complete all as specified and as directed. 135 M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate, isolated body (ISI Marked) complete all as specified and as directed. 136 Taking down old unserviceable regulator & supply & fix electronic type fan regulator stepped type on existing phenolic laminated sheet etc suitable for ceiling fan complete all as specified and as directed. 137 S&F in repairPVC/Polycarbonate Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings type with back plate suitable for batten fittingscomplete all as specified and as directed. Make: Anchor/ Legrand/ Havells or equivalent as mentioned in Appx of list of makes. 138 Taking doun old unsv sub main and M&L for sub main wiring with two runs of single core PVC insulated, unsheathed copper condutor, multi stranded cable of size 6.00 Sqmm 1100 volts grade drawn PVC concealed conduit of size19/20 mm (ISI marked) including PVC accessories complete incl cutting and chasing and making good etc including one run of 6.00 Sqmm single core copper conductormulti-stranded PVC insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by Engineer-in-Charge. Note : Two run of 6.00 Sqmm cable one run of 6.00 Sqmm cable as earth continuity conductor and one run of PVC Conduit shall be measured & paid as one unit.) 139 Supply, installation, testing and commissioning of 20 watt 4 ft long LED Batten housing made of extruded alluminium with milky white diffuser and inbuilt electronic driver system lumen output should be at least 1800 lumen with a CCT of 6000 K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed. 140 S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. 141 S&F in Repair sheet metal enclosure for MCB DB double door single pole & Neutral 8 way with 200 Amps rated bus bar all as specified and directed. 142 Taking down old unsv MCB and S&F SP 6 To 32 AMP amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 143 All as per item No 138 above but SPN 32 AMP complete all as specified and as directed. 144 S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1400mm sweep, with Squirrel cage induction motor all as specified and directed. 145 S&F exhaust fan, made of sturdy engineering plastic AC single Phase 230V of size 300 mm sweep with, blades, and frame and louvers cutting of the holes in existing wall and making good the surfaces all as directed. 146 M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick surrounded with charcoal and salt, buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanized iron15 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. 147 Supply and install steel tubular swaged poles type 410 SP-31 (9 mtr long) complete with CI base plate and finial taper plug,bolts, nuts and screws as specified all as directed. Note :-Excavation, earth work & PCC work only will be measured separetely all other accessories and work deemed to be included in quoted rate by the contractor. 148 M&L foor Earthing complete with galvanised steel earth plate electrode 60×60cm.x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 25 x 4 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed. 149 Supply, stringing and fixing on existing poles, ACSR conductor of any type/ size including fixing to insulators with binding wire complete all as directed. 150 M&L for PCC (1:4:8) type D2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete complete all as specified and as directed. 151 M&L for PCC (1:3:6) type C2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and as directed. 152 S&F for Air termination, single pointed aluminium rod 12mm dia and 300mm long complete all as specified and as directed.
