Miscellaneous Civil Works At Ms-I, Auto Grinding Shop And Spring Plant 3- Modules, Midhani Hyderabad- 58-0 BOQ for Module-I : Civil works for modification of Existing mould tapping pit & bottom pouring pit at Melt shop-I, Midhani Plant 1 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc., including dismembering and stacking within 50 metres lead 2 Carriage /carting of Dismantled steel structure by mechanical transport including loading, unloading and stacking upto lead of 1kms 3 Demolishing R.C.C work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 km, stacking and serviceable and unserviceable material separately including cutting reinforcement bars. 4 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m as directed by Engineer-in-charge. All kind of soils 5 Carriage /carting of Excavated Earth by mechanical transport including loading, unloading and stacking upto lead of 1kms 6 Filling available excavated earth (excluding rock) in trenches , plinth, sides of foundations etc., in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering , lead up to 50 and for all lifts 7 Carriage /carting of Excavated Earth by mechanical transport including loading, unloading and stacking upto lead of 1kms 8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 20 mm nominal size derived from natural sources) 9 Centering and shuttering including strutting, propping etc. and removal of form for upto ground level-walls of any thickness including attached pilasters, buttresses, plinth and string courses etc., 10 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (Thermo-Mechanically Treated bars of grade Fe-500D or more.) 11 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland Slag cement, admixtures in recommended proportions as per IS 9103 to accelerate / retard setting of concrete, to improve durability and workability without impacting strength including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering shuttering finishing and reinforcement as per direction of the EIC for the following grades of concrete:All works upto plinth level:Concrete of M30 grade with minimum cement content of 350kg/cum 12 Structural steel work in single section viz: angles, chanels, chequered plates etc,. fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaper washers etc., all complete. The cost includes providing gas cutting including gas bottles, welding machines, welding rods , all tools required is in the scope of contractor etc., complete as per instruction of E.I.C. (MAKE:VSP/TATA/JINDAL(JSW)) 13 Steel work in built up tubular (round, square or rectangular hollow tubes etc.,) trusses etc., including cutting, hosting fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washer etc., complete.Hot finished welded type tubes (MAKE:VSP/TATA/JINDAL(JSW)) 14 Providing and fixing bolts including nuts and washers complete 15 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 16 Providing & Plastering 18 mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand) with neat cement coat includes providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers per bag of 50 kg cement used in the mix. 17 Providing & fixing 3 mm thick translucent acrylic white sheets on roof/side cladding / for structural supports. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal , washers and tools, tackles under the scope of contractor 17.1 BOQ for Module-II : Civil works for enclosure around Electric panels in Auto Grinding Shop, Midhani Plant 18 Structural steel work in single section viz: angles, channels, chequered plates etc,.fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaper washers etc., all complete. The cost includes providing gas cutting including gas bottles, welding machines, welding rods, all tools required is in the scope of contractor etc., complete as per instruction of E.I.C.(MAKE:VSP/TATA/JINDAL(JSW)). 19 Providing and fixing bolts including nuts and washers complete 20 Providing & fixing toughened glass 12 mm thickness with aluminum/steel beading around glazing in partitions including cost of cutting to shape, fixing wastage at all heights & levels, drilling holes, providing silicon etc to complete; as per EIC. 21 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in MS structures partition with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in- charge. Pre-laminated particle board with decorative lamination on both sides. 22 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 23 Providing and fixing colour coated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 24 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to all/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). 25 Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 26 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer 26.1 BOQ for Module-III : Civil works for Metallic enclosure around Electrical panels in Spring Plant, Midhani 27 Structural steel work in single section viz: angles, channels, chequerred plates etc,. fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaper washers etc., all complete. The cost includes providing gas cutting including gas bottles, welding machines, welding rods , all tools required is in the scope of contractor etc., complete as per instruction of E.I.C. (MAKE:VSP/TATA/JINDAL(JSW)) 28 Providing and fixing bolts including nuts and washers complete 29 Providing & fixing toughened glass 12 mm thickness with aluminum/steel beading around glazing in partitions including cost of cutting to shape, fixing wastage at all heights & levels, drilling holes, providing silicon etc to complete; as per EIC. 30 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in MS structures partition with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in- charge. Pre-laminated particle board with decorative lamination on both sides. 31 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 32 Providing and fixing colour coated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 33 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to all/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). 34 Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 35 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer => Limited
