Annual Rate Of Work For Civil maintenance Works At Swm Department Of Morbi Muncipal Corporation, Dist :- Morbi-1 Excavation for foundation upto 1.5 mt. depth including sorting out and stacking of useful materials and disposing of the excavated stuff for all lead and lift (Loose or soft soil) Excavation for foundation upto 1.5 mt. depth including sorting out and stacking of useful materials and disposing of the excavated stuff for all lead and lift (Dense or Hard soil) Excavation for foundation upto 1.5 mt. depth including sorting out and stacking of useful materials and disposing of the excavated stuff for all lead and lift (Hard Murrum) Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering. Filling in plinth with sand under floors including watering ramming, consolidating and dressing etc. Complete Providing and laying cement concrete 1 : 4 : 8 (1 - Cement : 4 - coarse sand : 8 - hand broken stone aggregates 40 mm. nominal size) and curing complete excluding cost of formwork in (A) Foundtion & Plinth. Providing and laying cement concrete 1: 2 : 4 (1 - Cement : 2 - Coarse sand : 4 - crushed stone aggregates 20 mm. nominal size) and curing complete including cost of formwork in wall caps and copping. Providing and laying cement concrete 1: 11/2 : 3 (1 - Cement : 11/2 - Coarse sand : 3 - black stone crushed aggregates 20 mm. nominal size) and curing complete including cost of formwork in (A) Foundation Footing base of Column / Mass concrete. Providing and laying cement concrete 1: 11/2 : 3 (1 - Cement : 11/2 - Coarse sand : 3 - black stone crushed aggregates 20 mm. nominal size) and curing complete including cost of form work but excluding cost of reinforcement in (B) Slab, landing, shelves, Balconis, Lintels, Beams, Girders and Cantilever Upto floor two level. Providing and laying cement concrete 1: 11/2 : 3 (1 - Cement : 11/2 - Coarse sand : 3 - black stone crushed aggregates 20 mm. nominal size) and curing complete including cost of form work but excluding cost of reinforcement in (C) Columns, Pillars posts and struts upto floor two level. Providing and laying cement concrete 1: 11/2 : 3 (1 - Cement : 11/2 - Coarse sand : 3 - black stone crushed aggregates 20 mm. nominal size) and curing complete including cost of form work but excluding cost of reinforcement in (D) Staircase excluding landing upto floor two level. Providing TMT Bar FE 415 reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.cm. in foundation and plinth in Cement Mortar 1 : 6 (1- Cement : 6 - fine sand) (B) Conventional Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.cm. in foundation and plinth Cement Mortar 1:6(1-Cement:6-fine sand) Extra for brick work super structure above plinth level for all floor(B) Conventional Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg. / Sq.cm. in Cement mortar (1 - Cement : 5 - coarse sand) in foundation and plinth Extra for brick masonry in super structure for all floor (B) Conventional. Uncoursed Rubble Masonry with hard stone of approved quality foundation and plinth in cement mortar 1 : 6 (1- cement : 6 - coarse sand ) including levelling up etc. complete. Providing wood work in frames of Doors windows cleare story windows and other similar works, wrought framede & fixed position. (A) Indian Teak Wood Providing wood work in Trusses , Purlins Raffer posts, Post plates plates and the like wrought, frameo hoisted and fixed in position. Indian Teak Wood Providing wood work in frames of false- ceiling, partitions etc. sawn and put up in position.. (A) Indian Teak Wood Providing wood work in frames of Doors windows cleare story windows and other similar works, wrought framede & fixed position. (A) Indian Teak Wood 25 mm. thick wooden shelves supported on 40 mm. x 40 mm. x 6 mm. T or L iron brackets fixed at suitable distances but not exceeding cm. apart with Mango wood or equivalent quality. Providing and fixing M.S. round or square bars with M.S.flats required spacing in wooden frames of windows and clerestory windows. Providing and fixing Fly proof galvanised M.S. wire gauge of I.S.l gauge designation 85 G. with wire of dia.0.56 mm. to windows and celevating windows including 60 x 20 mm. beading of teak wood. Providing and fixing 35 mm. thick shutters for Doors, windows clerestory windows including Indian teak wood frames 10 cm. x 7 size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting complete. (i) Fully Glazed. Providing and fixing 35 mm. thick shutters for Doors, windows clerestory windows including Indian teak wood frames 10 cm. x 7 size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting complete. (ii) Fully Panelled. Providing and fixing 35 mm. thick shutters for Doors, windows clerestory windows including Indian teak wood frames 10 cm. x 7 size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting complete. (iii) Partly panelled and partly glazed. Providing and fixing FRP Frame size 100 x 50mm and 28mm thick Depress pannel shutter having extra reinforcement on sides and edges and in gel coat finish. The core of the shutter is to be filled up injected fire retardant grade polyurethane foam done insitu alongwith embedded wooden pieces for stiffening and also for taking hinges fixtures. The whole FRP Frame and shutter is to be water proof, weather proof, termite proof and resistance to mild acid/ Alkali. Rates are to be inclusive of S.S. hinges with necessary screws and alluminium fixtures and fastening. Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. (D) In trussses and trussed purlins, upto 25 M. span and 15 M. ovarall height. Providing and fixing sheet glass ordinary quality bedded in putty and fixed with wooden beadings including the cost of wooden beadings of first-class teak wood and necessary cutting of glass. (3) 3mm thick Providing and fixing PVC plain colour false ceiing with grid type with alu frame consisting of 600 mm x 600mm 3mm thick plain PVC sheet used as panel insert in a frame work made using anodized alluminium T section of size 1” x 1” (25 x 25mm, 19 gauge or 1mm thick) in square pattern of grid sizes of 2 x 2 (600 x 600mm). The alluminium frame work is supported from the ceiling with the help of G.I. hook and G.I. wire/6mm M.S. rods of required sizes to maintain proper level etc. The aluminium frame work is supported on side wall with the use of alluminium L section of size 1 x 1 (25 x 25mm) angles et. Complete as per direction of Engineer in charge. Manufactures, specification and drawing Providing and fixing PVC plain colour false ceiling with flush type with alluminium frame, frame work is done with three different sections of G.I. sheet of 24 gauge thickness named as C, U and L. The C section is fixed with hangers at an equal distance of 36” each and then U section is fixed perpendicular on C section with steel screws at an equal distance of 16” each. The complete frame work is supported by G.I. L angle 6mm rod hangers from the roof and L sections is fixed all around the wall as shown in the diagram. 5mm PVC sheet strips of size 2 wide and fixed with counter sunk steel screw on the U section. Further 3mm PVC sheet is stuck to these PVC strips with solvent cement such that joining lines are perfectly matched. P.U. putty is filled, ceiling for getting fine surface finish etc. Steel work, riveted in built up sections framed work i nccolmudpinlegtec uatst ipnegr, hoisting, fixing in position and applying a priming coat of read lead paint. (A) In beams and joists, channels angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hips and jack brafters, purlins conneted to common rafters and the like. Steel work, riveted in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. (B) In trussses and trussed purlins, upto 25 M. span and 15 M. ovarall height. Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. (A) In beams and joists, channels angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to common rafters and the like. Providing and fixing sheet glass ordinary quality bedded in putty and fixed with wooden beadings including the cost of wooden beadings of first-class teak wood and necessary cutting of glass. (4) 4mm thick Providing and fixing sheet glass ordinary quality bedded in putty and fixed with wooden beadings including the cost of wooden beadings of first-class teak wood and necessary cutting of glass. (3) 3mm thick. Deduct for difference in cost of materials and labour involved in method of glazing if changed in item No. 13 to (A) Front and back puttied and sprigged or fixed with glazing pins. . Providing and laying white glazed tiles 6 mm. thick in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1- cement : 3-coarse sand ) finishing with flush pointing in white cement. Providing and laying white glazed tiles 6 mm. thick in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3- coarse sand) and jointed with white cement slurry. Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. Providing and laying rough chiseled dressed stone flooring over 20mm thick base of cement mortar 1:5 (1-Cement : 5-coarse sand) or L.M. 1:1.5 including pointing with cement mortar 1:2 (1-cement : 2-stone dust) etc. complete. (A) 25 mm. thick. Providing and laying rough chiseled dressed stone flooring over 20mm thick base of cement mortar 1:5 (1-Cement : 5-coarse sand) or L.M. 1:1.5 including pointing with cement mortar 1:2 (1-cement : 2-stone dust) etc. complete. (B) 40 mm. thick. Providing and laying cement concrete flooring 1:2:4 (1-cement : 2- coarse sand : 4-graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement. (B) 50 mm. thick. Ceramic flooring tiles 8 MM. thick in flooring treads of steps & landing laid on a bed of 12 MM. thick cement mortar 1 : 3 (1 - cement : 3 - coarse sand) finished with a flush pointiung in white cement. Ceramic flooring tiles 8 MM. thick in skirting, risers of steps and dedo on 10 MM. thick cement plaster 1 : 3 (1 - cement : 3 - coarse sand) and jointed with white cement slurry. Providing asbestos cement sheets roofing fixed with G. I. plain and bitumen washer complete excluding the cost of purlins, rafters and trusses. (i) 7.5mm thick. Providing and fixing 150 mm. wide 450 mm. over all semicircular plain G. I. sheet class - 3 gutter with Iron brackets 40 mm. x 3 mm. size Bolts, Nuts, washers etc. including making necessary connection with rain water pipes. (i) 0.80 mm thick Sheet. Providing and laying Vitrified tiles 8 to 10 mm thick , 24 x 24 in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white cement. Providing and fixing tiles roofing with manglore tiles including teak reepers of sizes 50mm x 25mm. Providing and fixing sheet glass ordinary quality bedded in putty and fixed with wooden beadings including the cost of wooden beadings of first-class teak wood and necessary cutting of glass. (4) 4mm thick. Deduct for difference in cost of materials and labour involved in method of glazing if changed in item No. 13 to (A) Front and back puttied and sprigged or fixed with glazing pins. Providing and fixing poy carbonate 4 mm. sheets to round shape with M. S. Purlin of 25 x 25 mm. of 16 gauge this square pipe providing at 2.20 mt. center to center round shape and verticale three support including all labour charges riveting, bolting, welding failing the with silicon for water proof roof and oil painting with printer complete as per detailed drawing and as directed. Providing 10 mm. thick cement plaster in single coat on brick concrete walls for interior plastering for all floor level and finished even and smooth in (i) Cement mortar 1:3 (1- cement : 3-sand) Providing 15mm thick cement plaster in single coat on brick/concrete walls for interior plastering for all floor level and finished even smooth in (i) Cement mortar 1:3 (1- cement : 3-sand) Finishing wall with water proofing cement paint of on wall surface (Two coats) to give an approved brand & manufacture and of required shape even shade after thoroughly brushing the surface to remove dirt and remains of loose powered materials.. Painting Exterior wall acrylic emulsion ACE or equivalent quality on side wall by applying one coat primer white cement base coat applying to coats of acrylic emulsion paint of approved brand manufacture even shade after throatily brushing the surface remove all dirt and remains of loose powder materials etc. complete. Providing 15mm thick cement plaster in single coat on brick/concrete walls for interior plastering for all floor level and finished even smooth in (i) Cement mortar 1:4 (1- cement : 4-sand) 20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete. Pointing on Uncoursed stone masonry with cement mortar 1: cement : 3-coarse sand). (A) Flush pointing Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 including neat cement finishing, watering etc. complete. Removing dry or oil bound distemper by a washing and scraping sand papering the wall surface smooth including necessary repairs scratches complete. White washing with lime on wall surface (two coats) to give an shade including thoroughly booming the surface to remove all dust; mortar drops and other foreign Colour washing with lime on wall surface (two coats ) over including a primary coat of white washing to give an even shade through brooming the surface to remove all dirt, dust, mortar and other foreigh matter. Distempering (Two coats) with oil bound distemper of approved and manufacture and of required shade on wall surfaces to give even shade, over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing surface free from mortar dropping and other foreign matter and including preparing the surface even and sand papered smooth. Finishing Wall with Weather Proof Exterior Emulsion Paint on Surface (Two Coats) to give an required shape even shade thoroguhly brushing the surface to remove all dirt, and remains loose powdered materials etc. complete Applying Two Coats of Birla or Asian Acrylic Lappy (Putty) and two coats of primer of approved brand and manufacture on New Wall Surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth. Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. Painting three coats (including priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter. Painting two coats (excluding priming coat) on previously painted steel and other metal surface with enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter for every subsequent coat of paint. Painting two coats (excluding priming coat) on previously painted wood and wood based surface with enamel paint, to give an even shade including cleaning the of all dirt, dust and other foreign matter for every subsequent coat of paint. Painting three coats (excluding priming coat) on new wood and wood based surface with enamel paint, interior to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping for every subsequent coat of paint. Polishing with french polish on new wood and wood based surface to give an even surface including cleaning, the surface of all dirt, dust and sand papering smooth and including a coat of wood filler. Demolition and disposal of unserviceable materials with all lead and lift. (i) Unreinforced concrete. Demolition of Brick work and stone masonry including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. (ii) In Cement Mortar. Demolition of terrace including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. (i) Brick tile covering. Dismentling doors, windows, venti- lators etc. (wood or steel) shutters including chowkhats architraves, holdfasts and other attachment etc. complete and stacking them within all lead and lift. (i) Not exceeding 3 Sq.M. in area. Scraping oil paint from steel and other metal surface and making the surface even (with Hand Scraping.) Providing and fixing 1.20 Mt. high fencing with 1.50 Mt. high 10 cmn. X 10 cm. C. C. 1 : 2 : 4 precast post (3.00 mm. steel br 4 Nos.) fix at 2.5 mt. C / C with five Horizontal lines and two diagonals of galvanized steel brbed wire weighting 9.38 Kg. per 100 Mt. strained and fixed to posts with G. I. Staples including fixing the posts in ground with 0.45 M x 0.45 M x 0.45 block in C. C. 1 : 2 : 4 etc. complete 100 mt. length. Providing and fixing 1.20 Metre high fencing with 2.0 Metre long M. S. angle post 40 mm. x 40 mm. x 6 mm. and oil painting 3 coats fixed at 2.5 Mt. C/C. with five Horizontan lines and two diagonals of galvanised steel barbed wire weighting 9.38 Kg. per 100 Metre, strained & fixed to posts with G. I. staples including fixing the postsin ground with 0.5 M x 0.5 M x 0.5 M. block in C. C. 1 : 5 : 10 etc. complete. Carring out plinth treatment to post construction / existing structure by spraying chemical solution for termite control treatment including labour and material consistment with I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration Weight one percent is recommended i.e one litre Carrying out timber treatment to all wood work in 2c0lu EdCin cghedmrililcinagl holes and spraying oil based chemical solution on surface of timber work for termite control including labor and material etc. complete. Using Chlorpyriphos20 EC as per 6313 Applying general insecticide pest control treatment to floors, cupboards etc including labour materials etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075 concentration by Pmraosvsid) iins greaconmd mfixeinndgetdo 10w.a5lml, l ccehielinmgicaanl ddilufltoeodr wgiatlhv a5n liisteerds oMf iwldatseter el tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. (A) 15 mm. Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. (C) 25 mm. Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. (E) 40 mm. Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes (Medium grade) of the following nominal bore, tube fitting and clamps including making good the wall ceiling and floor. (F) 50 mm. Providing and laying in trenches galvanised mild steel tubes (Midium grade) of the following nominal bore, and tube fitting (Earthwork in trenches to be measured and paid for separately) (C) 25 mm. Providing and laying in trenches galvanised mild steel tubes (Midium grade) of the following nominal bore, and tube fitting (Earthwork in trenches to be measured and paid for separately) (D) 40 mm. Providing and laying in trenches galvanised mild steel tubes (Midium grade) of the following nominal bore, and tube fitting (Earthwork in trenches to be measured and paid for separately) (E) 65 mm. Providing and laying in trenches galvanised mild steel tubes (Midium grade) of the following nominal bore, and tube fitting (Earthwork in trenches to be measured and paid for separately) (F) 80 mm. Providing and fixing plastic seat and cover for wash down water closer with C. P. brass hinges and rubber buffers. (B) Black plastic seal and cover. Providing and fixing C. P. brass waste for wash basin or sink. (A) 32 mm. dia Providing & fixing C. P. brass shower rose with 15 mm. or 20 mm. inlet. (A) 100 mm dia. Each Providing and fixing 600 mm. x 450 mm. bevelled edge mirrror of superior glass mounted on 6 mm. thick A. C. sheet or plywood sheet and fixing to wooden pluge with C. P. brass screws and washers. Providing and fixing screw down bib taps of following size. (A) Brass chromium plated screws down Bib Tap. (i) 15 mm. dia. Providing & fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15 mm. dia. Providing and fixing brass screw down stop tap. (A) 15 mm. dia. Providing and fixing Gun metal check or non-return fullway wheel valve. (C) 25 mm. dia. Providing and fixing Gun metal check or non-return fullway wheel valve. (E) 40 mm. dia. Providing and fixing chromium plated brass half trun flush cock approved quality including fixing in pipe line etc. complete.(iii) 32mm dia. Providing and fixing coloured Anodised Aluminium section sliding window with two track frame size 82.50 x 44.00 mm. and 1.7 mm. average thick and fully glazed transparent glass shutters with coloured anodised aluminium section framing 43.25 and 1.7 mm. average thick 8.00 mm. thick aluminium glazing clips and rubber bidding and including anodised aluminium fixture and fastening and hold fasting with coach bolt etc. complete. Providing and fixing PVC Square water tank of Sintex company on wall with necessary angle required with necessry G. I. Fitting over flow pipe bol valve, clamp nipple as directed. Providing and laying inter locking precast tiles of 60 mm. x to 65 mm. in floors and laying 20mm thick bed of cement mortar 1:6 (1-cement 6-coarse sand) or L.M. 1:1.5 jointed with neat cement slurry with pigment to match the shade of tiles complete Providing and fixing 25 mm. thick polished Kota Stone bothside polished selves in wall clip bound includfing groove in wall fixing polishing both side etc. complete. Providing and fixing Cup board using Indian Teak wood frame of 70 35 mm. and fixing 19 mm. thick commercial ply wood shutter including fixtures, oil painting etc. complete. Providing and fixing Pre laminated particle board shutter of 18 mm. thick including fixtures and fastening including non teak wood frame size of 90. x 30 mm. fixing in Kota stone by drilling and screw directed. Providing and replacing existing damaged C. B. shutter using both side 4 mm. thick commercial plywood non teak wood including fixtures and fastening and oil paint etc. complete with all labour and materials. Providing cooking platform of 60 cm. width and 70 cm. height including 25 mm. thick side polished Kota Stone vertical and horizontal support and including fixing of steel sink cutting in plateform as design including cost of cement (Using granite stone over Kota slab top) Providing cooking platform of 60 cm. width and 70 cm. height including 25 mm. thick side polished Kota Stone vertical and horizontal support and including fixing of steel sink cutting in plateform as design including cost of cement (Using Marble stone over Kota slab top) Providing cooking platform of 60 cm. width and 70 cm. height including 25 mm. thick side polished Kota Stone vertical and horizontal support and including fixing of steel sink cutting in plateform as design including cost of cement (Curing Single stone ) Constructing brick masonry chamber for underground C. I. Inspection chamber & bends with bricks having crushing strength not less than 35Kg./ Sq.Cm in C.M. 1 : 5 C. I. cover with frame (Light duty) 455 mm. x 610 mm. intenal dimensions, total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg. and Wt. of frame 15Kg. ) R.C.C. top slabe with 1 : 2 : 4 mix (1 - cement : 2 - coarse sand : 4 - graded stone aggregate 20 mm. size) foundation concrete 1 : 5 : 10 inside plaster 15 mm. thick with cement mortar 1 : 3 finished smooth with a floating coat of neat cement on walls & bed concrete etc.complete. Including precast cement concrete 1 : 2 : 4 cover with frame of 5.00 mt. capacity inside dimension 455 mm. x 610 mm. and 450 mm. deep for single pipe line. Providing and fixing Aluminium sliding three track window and top fix vewnt having size 92 mm. x 31.75 mm. including shutter frame size 18 mm. x 40 mm. sliding type on for S. S. wire gauge shutter including rubber bidding PVC virgin, P Smoke Gray 4 thick glass maruti type handle, bearing, fixtures and fastening etc. including all labour and materials etc. complete. Providing and fixing Aluminium sliding four track window having frame size 122 mm. x 31.75 mm. including shutter frame size 18 mm. x 40 mm. sliding type on track for S. S. wire gauge shutter and top for vent having frame size 101.60 x 44.45 mm. size extra angle at bottom of 25.00 x 44.00 mm. including rubber bidding PVC virgin, P Smoke Gray 4 thick glass maruti type handle, bearing, fixtures and fastening etc. including all labour and materials etc. complete. Flushing cistern P.V.C. with fittings 12.5 Litre high level Providing and fixing 35 mm. thick shutters for doors, window and cear story windows including black enamaled M. S. butt hinges with necessary screws. (A) Indian Teak wood (i) Fully Panelled (Aluminium fitting and fastening.) Providing and fixing 35 mm. thick shutters for doors, window and cear story windows including black enamaled M. S. butt hinges with necessary screws. (A) Indian Teak wood (iii) Partly Panelled and Partly glazed. Providing and fixing 35 mm. thick shutters for doors, window and cear story windows including black enamaled M. S. butt hinges with necessary screws. (A) Indian Teak wood (iii) Partly Panelled and Partly glazed. Providing and fixing 30 mm wire gauge shutters using galvanised M.S. wire of I.S. gauge designation of 85 G. with wire of 0.56 mm dia, for Doors, windows and clearstory windows including bright finished or / and black enamellede M.S. butt hinges with necessary Mango wood or equivalent quality. Providing and fixing 30 mm wire gauge shutters using galvanised M. S. wire of I.S. gauge designation of 85 G. with wire of 0.56 mm dia, for Doors, windows and clearstory windows including anodised alluminium butt hinges with necessary screws. Providing and fixing Non teak wood 30 mm. thick fly proof shutter with Non teak wood frame 50 x 40 mm. size including two coats of oil paint and 1 coat of primer and aluminium fitting and fastening etc. complete. Providing and fixing Teak wood 30 mm. thick fly proof shutter with Teak wood frame 50 x 40 mm. size including two coats of oil paint and 1 coat of primer and aluminium fitting and fastening etc. complete. Reapirs to doors and window shutters by providing necessry teak wood member and necessry hardware fitting and including touching the new memmber by matching existing oil painting shed etc. complete as directed including all cost of labour and materials. Reapirs to doors and window shutters by providing necessry non teak wood member and necessry hardware fitting and including touching the new memmber by matching existing oil painting shed etc. complete as directed including all cost of labour and materials. Providing and fixing flush door shutters, solid core construction with frame of first class hard wood with cross band and face veneer or plywood face panels, including anodised aluminium but hinges with necessary screws, (B) Non decorative type and block board core anodised aluminium butt hinges in flush door shutters (2) 35 mm. thick. Repairs to rolling shutters including clening, oiling, greasing, servicing and fitting in original position as directed including all cost of labour and materials. Providing and fixing rolling shutters of approved make made of 80 mm wide M.S. laths inter-locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and Providing and fixing in position callapsible steel shutters with vertical channels 20 x 10 x 2 mm. braced with flat iron diagonals 20 x 5 mm. size with top and bottom rails of T- iron 40 x 40 x 6 mm. with 38 mm. dia, steel pulleys complete with bolts, nuts, locking arrangements, stoppers handles including applying a priming coat of read lead paint. Reapirs to A. C. sheet roof by providing new 6 mm. A. C. sheet instead of damage sheet and providing Lodhia vata etc. complete as directed including all cost of labour and materials. Reapirs to M. T. roof including replacing old damage Manglore tiles providing new M. T. repairs to batten patti, Lodhiya vata as directed including all cost of labour and materials (Excxluding cost of rafter.) Providing 22 gauge aluminium sheet in existing door, window shutter as directed including cost of labour and materials. Providing and fixing Orrissa Pan 580 mm. size including necessary connection P - Trap, chromium plated brass flush cock 25 mm. dia etc. complete as directed including all cost of labour and materials. Providing and fixing cast iron spigot and socket soil, waste and ventilating pipes of the following nominal size. (B) 75 mm. dia. Providing and fixing cast iron spigot and socket soil, waste and ventilating pipes of the following nominal size. (C) 100 mm. dia. Providing and laying (to level or slopes) & jointing with stiff mixture of Cement Mortar in proportion 1 : 1 salt glazed stoneware pipes including testing of pipes and joints complete. (A) 100 mm. dia. Providing and laying (to level or slopes) & jointing with stiff mixture of Cement Mortar in proportion 1 : 1 salt glazed stoneware pipes including testing of pipes and joints complete. (B) 150 mm. dia. Cleaning the septic tank including digging the sludge and disposing away as directed. Providing sock pit of 2.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing, curing etc. complete as directed. Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure polythene pipes of the following outside dia, low densidy, complete with special falnge compression type fittings, wall clips etc. including making good the wall ceiling and floor. (B) 25 mm. Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(C) 32mm Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(D) 40mm Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(E) 50mm Providing erecting fixing double coated Syntex of Equivalent PVC (ISI) Mark Water Tank of Required Capaicty each with all necessary fittings & connection etc.complete on Terrace. Providing and fixing 600 mm. x 450 mm. bevelled edge mirrror of superior glass mounted on 6 mm. thick A. C. sheet or plywood sheet and fixing to wooden pluge with C. P. brass screws and washers. Spreading blindage or road crust filling the gaps in metal and leveling to camber and gradient as directed. (i) Murrum Supplying and stacking of standard quality brunt clay building bricks on site with an average 40 Km. lead. as directed (Conventional brick size = 22.5 x 11 x 7.5 cm.) White Stone Bela mesonry block in course in super structure with stone of approved quality in Lime Mortar 1:6 (1-Cement : 6- course sand) including packing the joints etc. complete. White Stone Bela mesonry work in partition walls upto 15 cm. thick thickness in Cement Mortar 1:4 (1-Cement : 4- course sand). Providing and laying grnite 18 mm. thick in riser of steps, Dedo and pillars laid on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry including rounding and moulding etc. complete. Providing and fixing brass screw down stop tap. (i) 15 mm. dia. Providing and fixing C. P. brass towel rail complete with C. P. brass brackets fixed to wooden plugs with C.P. brass scews. (B) 600 mm. x 20 mm. size. Providing and fixing screw down bib taps of following size. (B) Brass chromium plated down Bib Tap screws (i) 15 mm. dia. Providing & fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15 mm. dia. Providing and fixing Gun metal check or non-return fullway wheel valve. (A) 15 mm. dia. (A) 15 mm. dia. (B) 25 mm. dia. Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall concealed in walls as directed including necessary fittings such bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Dismentaling tiled or stone floors laid in mortar including stacking serviceable materilas and disposal of unserviceable materials with lead and lift. Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] mm. (B) 20 mm. dia. (B) 25 mm. dia. Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved design Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with sand in proper line and level as per guidlines Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm length,30cm height and 15cm thick M250 grade concret as per approved design and including excavation for fixing in proper line and level,filling the joint with C:M (1cement:3fine sand) etc complete. (C) 32 mm. dia. (D) 40 mm. dia. (E) 40 mm. dia. (E) 50 mm. dia. (A) 15 mm. dia. (F) 50 mm. dia. Providing laying and jointing in true line and level 15mm dia. U.P.V. Pipe ( SCH- 40) for cold water including fittings as approved Engineer In Charge. Pipe shall be fixed on the wall with the help clamp at every two metre C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials. Providing and laying broken China Mosaic flooringvfor terrace using mm. to 20 mm. broken piece of glazed tiles to be laid over cement mortar 1 : 3 to plain or slope and to be tempered to bring mortar crème out upto sirface using white cement including rounding junctions and extending them up to 15 cm. along the wall, clearing with water and oxalic acid etc. as directed. Removing and scraping of old deteriorated Plaster of any thickness from wall / RCC member including stacking of serviceable material and disposal of unserviceable from site of work with all lead and lift. Demolition including stacking of serviceable materilas and disposal unserviceable materials with all lead and lift. (i) RCC Work (A) 15 mm. dia. (C) 25 mm. dia. (D) 32 mm. dia. (A) 160 mm. dia. (B) 110 mm. dia. (A) 100 mm. dia. Providing and fixing Stainless steel kitchen sink - without drain board 610x460 mm bowl depth 200 mm Supplying OPC 53 grade Fresh Cement on site with all lead.and lift directed incuding all taxes without star rate Supplying of Good Quality River Fine Sand on site with all lead.and as directed incuding all taxes Supplying of Machine Crushed Stone Aggregate hard Quality 10 mm size on site with all lead.and lift as directed incuding all taxes Supplying of Machine Crushed Stone Aggregate hard Quality 20 mm size on site with all lead.and lift as directed incuding all taxes Supplying of Machine Crushed Stone Aggregate hard Quality 40 mm size on site with all lead.and lift as directed incuding all taxes (B) 75 mm. dia. Providing and fixing PVC SWR Nahni Trap IS 14735 for drain with jali of the following nominal diameter of self cleansing design with C. Scrwed down or hinged grating including the cost of cutting and making good the walls. Providing Labour Compressar Operator on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Bandhani on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Bhisti on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Blacksmith 1st Class on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Blacksmith 2nd Class on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Breaker on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Carpentar 1st Class on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Carpentar 2nd Class on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Bullock with Driver to Mortar Mill on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Chowkidar on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Crane operator with Helper on Site as Per Situation Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Excavator on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Hole Driller on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mason 1st Class on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mason 2nd Class on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mate on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mazdoor (Female) on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Handcart with Mazdoor on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Glazier on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Fitter on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Extra labar sinking and chisselling on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mazdoor (Male) on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mistry on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Painter on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Plumber (Fitter) on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Plumber(Fitter)Assist on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Polisher on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Spraymen on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Supervision for Machinery on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Welder on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour White Washer on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Winch Operator on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing & fixing M.S. Grill for with necessary fitting with necessary fitting with one coat of primer and two coat oil paint as per details given by architect. as per attached detail architectural drawing. Providing Unskilled Labour on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Mazdoor with Hand Cart on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing helper on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Labour charges Beldar on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Chiseller (Semi Skilled) on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Applicating Operator on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour Applying Two Coat of Preventitive Coating on Steel per day (Painter) on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Labour for Removing (Descaling) Rust & Applying one coat per day (Semi Skilled) on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area Providing Semi Skill helper on Site as Per Situation & Guidance Given By Engineer in Charge For M.M.C Area
