Tender For Provision Of Certain Essential Facilities At Itr Residential Colony Balasore; 1 NOTE (Applicable for all items) :-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.(ii) The bidders / contractors are advised to quote same rate for same items as mentioned in both parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt.SCHEDULE A PART-I (B/R works) 1.001 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard /dense soil complete all as specified and directed. 1.002 M&L for cement concrete 1:4:8, type D2 (40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. 1.003 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified and directed. 1.004 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. 1.005 M&L for Reinforced cement concrete (design mix) M-30 (20 mm greded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 1.006 M&L for Reinforced cement concrete (design mix) M-30 (20 mm greded stone aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed. 1.007 M&L for Reinforced cement concrete (design mix) M-30 (20 mm greded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. 1.008 M&L for Reinforced cement concrete (design mix) M-30 (20 mm greded stone aggregate) in chajjas complete all as specified and directed. 1.009 M&L for Reinforced cement concrete (design mix) M-30 (20 mm greded stone aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 1.010 Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 1.011 Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. 1.012 Formwork to sides of Rough finished surfaces concrete pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. 1.013 Formwork to soffits of Rough finished surfaces concrete suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. 1.014 Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. 1.015 Formwork to Rough finished surfaces concrete chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. 1.016 M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 1.017 All as per item 1.016 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders 1.018 M&L for brick work with flyash bricks old size, straight or curved on plan exc 6 m mean radius built in cement mortar CM (1:6) etc complete all as specified & directed. 1.019 M&L for sand filling under floors or in foundation incl watering and consolidation complete all as specified and directed. 1.020 M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 1.021 M&L for PCC 75 mm thick 1:3:6 type C1 (20 mm graded stone aggregate) as in sub base complete all as specified and directed. 1.022 M&L for PCC 25 mm thick 1:2:4 type B-0 (12.50 mm graded stone aggregate) as in floor complete all as specified and directed. 1.023 M&L rendering 10mm thick cement plaster in CM (1:4) on fair faces of brick work for fixing of wall tiling complete all as specified and directed. 1.024 M&L for 15 mm thick screed bed or bedding layer of mortar in CM (1:6) for laying floor finishes for non skid ceramic and granite tiles complete all as specified and directed. 1.025 M&L Glazed ceramic colour tiles in vertical surface 450 X 300 X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles complete all as specified and directed. 1.026 M&L Non Skid colour ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exc 0.11 sqm in floors etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified and directed. 1.027 M&L Non Skid coloured ceramic tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified and directed. 1.028 -Ditto all as item No 1.027 but as in skirting 1.029 M&L granite slab (of any type) 18-20 mm thick machine cut, bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including cutting and polishing complete all as specified and directed. 1.030 M&L for 10 mm thick in CM (1:6) rendering on brick wall or concrete surfaces finished even and smooth without using extra cement on wall complete all as specified and directed. 1.031 M&L for 5mm thick cement plaster in cement mortar CM (1:3) on ceiling, and finished the surface even and smooth without using extra cement complete all as specified and directed. 1.032 M&L for 15 mm thick 1:4 cement plaster with WPC as per manufacturer instruction and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately.) 1.033 M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper (ready mixed) having VOC content less than 50gms/litre of approved manufacturer of required shade and colour complete, as per manufacturer specification over a coat of alkali-resiatant primer complete all as specified and directed. 1.034 M&L three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and as directed. 1.035 M&L for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. 1.036 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkhat of size Frame size 65x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fas/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. 1.037 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.(Note: Stainless steel butt hinges and necessary S.S screws shall be measured and paid separately) 1.038 All as per item No 1.037 but in 30 mm thick mosquito proof door shutter 1.039 S&F of solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with MS square tube, suppling complete all as specified and directed. 1.040 S&F of factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC C channel moulded both side Prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles prelam PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of both side Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed. 1.041 S&F of powder coating minimum thickness 50 micron Anodised aluminium frame for doors / windows / ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed. 1.042 S&F for powder coating minimum thickness 50 micron Anodised aluminium window shutters sliding/openable type and ventilator top hung type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber neoprene packing, handles 2 Nos in each window, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.(Note : Glass and wire mesh shall be measured and paid separately.) 1.043 M&L for 5.00 mm thick Sheet glass, ordinary quality incl necessary fixing complete all as specified and directed. 1.044 S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with SS wire stapple complete all as specified and directed. 1.045 S&F 4mm thick Figured glass, pin head type and glazing with oil putty or securing clips complete all as specified and directed. 1.046 S&F 100 mm size of Stainless steel hinges (ISI Marked) complete all as specified and directed. 1.047 S&F 125 mm long extruded Aluminium alloy handles, fabricated type anodised complete all as specified and directed. 1.048 S&F 125 mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed. 1.049 S&F aluminium sliding door bolt 250 mm long, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed. 1.050 S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as specified and directed. 1.051 S&F for Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position as required. In steel Door and Ventilator, frames, guard bar, ladder, railings, brackets, gates, grill and similar works complete all as specified and directed. 1.052 M&L for two coat of synthetic enamel paint on new steel surfaces of any description incl one coat of red oxide primer, over 10cm width or girth after preparation complete all as specified and directed. 1.053 Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. 1.054 Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. 1.055 S&F wash down water closet (EWC) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as specified and directed. 1.056 Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed. 1.057 S&F vitreous china wash basin, white, flat back size 550x400mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets, waste pipe, waste coupling complete all as specified and directed. 1.058 S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed. 1.059 S&F 500 litre capacity rotational moulded polythylene tripple layer water storage tank with cover and suitable locking arrangement (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed. 1.060 S&F PVC ball valves high pressure with polythene float and fly nut complete, screwed for iron pipe of 20mm bore complete all as specified and directed. 1.061 S&F 15mm dia fancy type CP bib taps, cast copper alloy with crutch or butterfly handle, screwed down fixed complete all as specified and directed. 1.062 S&F 15mm dia fancy type CP pillar taps, cast copper alloy with capstan head, chromium plated screwed down fixed high pressure, long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. 1.063 S&F 15 mm dia CP angular stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or unions complete all as specified and directed. 1.064 S&F 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screws and cup washers without aluminium frame complete all as specified and directed. 1.065 S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. 1.066 S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long complete all as specified and directed. 1.067 S&F Brass CP tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed. 1.068 S&F 20 mm CPVC Ball Valve (Gate Valve) complete all as specified and directed. 1.069 S&F 100 mm dia PTMT grating for kitchen wash hand basin complete all as specified and directed. 1.070 S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including necessary brackets clamps or laid in trenches complete all as specified and as directed. 1.071 S&F 40 mm bore PVC(SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including necessary brackets clamps or laid in trenches complete all as specified and as directed. 1.072 S& F 75 mm PVC Nahani Trap complete all as specified and directed. 1.073 M&L for 3mm thick APP modified non-woven polyester reinforced bituminous membrane with mineral slate granules and flexible at -2 °C (Sika shield P 24 MG or equivalent) water proofing membrane weight not less than 3 Kg/sqm including one coat of bituminous primer for bitumen membrane @ 0.4 lit/sqm over plaster surface. Over the primer coat the membrane shall be laid using butane torch and sealing all the joints etc complete all as specified and directed. Note : The laying of membrane shall be got done through the authorised applicator of the manufacturer. 1.074 M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:4) finished surfaces even and smooth with WPC complete all as specified and as directed. (Note : WPC shall be measured and paid separately) 1.075 Supply only integral water proofing compound (ISI marked) of approved make. 1.076 S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 1.077 S&F 75 mm SWR fitting Vent Cowl with wire mesh complete all as specified and directed. 1.078 M&L for PCC 50 mm thick type C2 1:3:6 (20mm stone aggregate) as in plinth protection, paving finised the surface even and smooth without using extra cement complete all as specified and directed. 1.079 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead, Nominal concrete 1:3:6 complete all as specified and directed. 1.080 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 75mm thick 1:3:6 stone aggregate 20 mm size complete all as specified and directed. 1.081 S&F for Paving vitrified parking tiles 300 mm x 300 mm x 8 to 10 mm thick (heavy duty), jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, over and including 20 mm thick screed bed of 1:4 cement mortar complete all as specified and directed.Note- Medium shade pigment using 50% white cement 50% Grey cement . 1.082 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge 1.083 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m all type of soil. 1.084 M&L for cement concrete 1:2:4 stone aggregate 20 mm nominal size for Haunching concrete complete all as specified and directed. 1.085 M&L for brick work with flyash bricks old size, straight or curved on plan exc 6 m mean radius built in cement mortar CM (1:4) etc complete all as specified & directed. 1.086 M&L 12 mm cement plaster smooth finish of mix : 1:4 without using extra cement complete all as specified and directed. 1.087 M&L 12 mm cement plaster of mix CM : 1:4 with using extra cement complete all as specified and directed. 1.088 M&L 6 mm cement plaster of mix Cm : 1:3 complete all as specified and directed. 1.089 M&L for Reinforced cement concete (1:1.5:3) (Nominal mix) using 20 mm graded stone aggregate as in roof slabs fro septic tank complete all as specified and as directed.(Note : Reinforcement shall be measured and paid separately) 1.090 M&L for Reinforced cement concete (1:1.5:3) (Nominal mix) using 20 mm graded stone aggregate as in baffle wall and septic tank complete all as specified and as directed. (Note : Reinforcement shall be measured and paid separately) 1.091 M&L for Form work Centering and shuttering including strutting, propping etc. and removal of form for baffle wall complete all as specified and directed . 1.092 Supply and fixing 100 mm dia cast iron and vent pipes complete all as specified and directed . 1.093 Supply and fixing 75 mm dia cast iron and vent pipes complete all as specified and directed . 1.094 S & F CI vent cowl of 100 mm complete all as specified and directed . 1.095 Supply and fixing 75 mm gate valve with C.I. wheel of approved quality (screwed end) complete all as specified and directed . 1.096 S&F C.I. cover without frame for manholes for manhole, septic tank 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg complete all as specified and directed . 1.097 M&L for two coat of Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade complete all as specified and directed . 1.098 S&F 100mm dia HDPE double wall corrugated SN 8 underground drainage/sewer pipes, confirming to IS 7328, single socketed in any length jointed with solvent cement laid in trenches or floors etc complete all as specified and as directed . 1.099 All as per Item No 1.098 above but 150mm dia pipe complete all as specified and directed . 1.100 M&L for 100mm dia pipes concrete bed to drain pipe including packing under and haunching against sides of pipes after they are laid and tested in PCC 1:3:6, type C-2, using 40mm graded stone aggregate complete all as specified and directed . 1.101 All as per item 1.100above but 150 mm dia complete all as specified and directed . 1.102 M&L precast reinforced cement concrete(1:1.5:3) (using 20mm graded stone aggragate) as cover slab set in cement mortar 1:6 complete all as specified and directed . 1.103 M&L for plain cement concrete (1:2:4) (using 20 mm graded stone aggregate) as in copings, bed plates etc, including necessary form workcomplete all as specified and directed . 1.104 Supply and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type with fly ash bricks complete all as specified and directed . 1.105 M&L for Reinforced cement concrete (design mix) M-30 (20 mm greded stone aggregate) in drain wall complete all as specified and directed. 1.106 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m complete all as per specifies and directed. 1.107 Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete all as per specifies and directed. 1.108 M&L for Stone (polished) work Granite 16-18 mm thick of any colour and shade for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete all as per specifies and directed. 1.109 M&L for Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 graded stone aggregate 20 mm nominal size complete all as per specified and directed 1.110 M&L for Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 graded stone aggregate 20 mm nominal size complete all as per specified and directed 1.111 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement complete all as per specified and directed. 1.112 S&F Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron Y shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer- in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) 1.113 M&L for Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position using structural steel etc. as required : In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete all as per specified and directed. 1.114 M&L Painting New Steel work with Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture complete all as per specified and directed. 1.115 Demolition of cement concrete (unreinforced) in ground floors and pavings, etc. n exc 15cm thickness (below or above ground level) as in surface channel, coping etc. and removing debris and rubbish out of the premises complete all as specified & directed. 1.116 M&L for 100 thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and as directed. 1.117 M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade with grey cement & pigment complete all as specified and as directed. 1.118 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 1.119 Demolishing brick work built in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete as per direction. 1.120 Providing and laying 20 mm nominal size graded stone aggregate 1:2:4 cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, piers, abutments, pillars, Column posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc. excluding the cost of centering, shuttering and finishing complete all as specified and directed. 1.121 M&L for Reinforced cement concete (1:1.5:3) (Nominal mix) using 20 mm graded stone aggregate as in beams, suspended floors, roofs landings, lintels bands, excluding the cost of centering, shuttering, finishing complete all as specified and directed. 1.122 M&L for Centering and shuttering including strutting, propping etc. and removal of form for Edges of RCC band and breaks in floors and walls Under 20 cm wide complete all as specified and directed. 2.00 NOTE (Applicable for all items) :-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.(ii) The bidders / contractors are advised to quote same rate for same items as mentioned in both parts of BOQ If quored rates are different for same items, lower quoted rate shall be considered for same items as mentioned in BOQ. For this account nothing extra shall be admissible by this Deptt. SCHEDULE A PART-II (E/M works) 2.01 Wiring for light point/ fan point with 1.5 sq.mm FRLSH PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet,suitable size M.S. box and earthing the point with 1.5 sq.mm.FRLS PVC insulated copper conductor single core cable etc complete all as specified and directed. 2.02 Wiring for power plug for 15A inndepenent switch socket board and on the same board with 2X4 sq. mm FRLSH PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required complete all as specified and directed. 2.03 Wiring for 05A indepenent switch socket board with 2X1.5 sq. mm FRLSH PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 1.5 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required by complete all as specified and directed. 2.04 Supplying and fixing metal box of 100mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required complete all as specified and directed. 2.05 Supplying and fixing metal box of 150mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required complete all as specified and directed. 2.06 Supplying and fixing 3 pin 5/6 A socket outlet on the existing switch box/ cover including connections to independ board as required complete all as specified and directed. 2.07 Supplying and fixing 6 pin 15/16 A socket outlet on the existing switch box/ cover including connections etc. as required complete all as specified and directed. 2.08 Supplying and fixing 5/6 A switch on the existing switch box/ cover including connections etc. as required complete all as specified and directed. 2.09 Supplying and fixing 15/16 A switch on the existing switch box/ cover including connections etc. as required complete all as specified and directed. 2.10 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required complete all as specified and directed. 2.11 Supplying and fixing 6 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required complete all as specified and directed. 2.12 Supplying and fixing 5-32A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required complete all as specified and directed. 2.13 Supplying and fixing 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of Single pole and Neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required complete all as specified and directed. 2.14 S&F in repair LED type intigrated batten fitting indoor decorative polycarbonate housing & diffuser with integrated LED driver 20W white complete all as specified and directed. 2.15 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc complete all as specified and directed. 2.16 Supply, install & testing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers fixed to wall with suitable size bolts, grouted to wall and connecting up including provision of cable from connector to fan with three core flexible cable of size 24/0.2mm with copper conductor from ceiling rose to exhaust fan complete all as specified and directed. 2.17 S&F security light fitting of capacity 45 watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 complete all as specified and directed. 2.18 Supply & Fixing of GI pipe bracket of 40 mm dia light grade pipe bend to shape of approx length 1.5 mtr including 2 no MS clamp of flat iron size 40×6 mm complete with nut bolt washer complete all as specified and directed. 2.19 Supplying and fixing PVC batten/ angle holder including connection complete all as specified and directed. 2.20 S&F LED lamp 15 W 500 lumen output, B22 holder complete all as specified and as directed 2.21 Materials and labour for earthing as in repair complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised strip of size 25 x 5 mm by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 40 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on complete all as specified and directed. 2.22 S&F 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. complete all as specified and directed. 2.23 Supply, connecting and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core including connection cable glands, aluminium lugs etc complete all as specified and as directed. 2.24 Supply, connecting and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 2 core including connection cable glands, aluminium lugs etc complete all as specified and as directed. 2.25 M&L for sand cushioning in trenches for protection of under ground cable 8 cm before laying the electric cable and 15 cm after laying the cable and punning down, complete all as specified & directed.Note : For the purpose of payment only punned down thickness shall be measured. 2.26 M&L for laying of fly ash bricks locally available for cable protection cover laid flat and dry in trenches over the cable prependicular to the direction of cable complete all as specified & directed. 2.27 Supplying and embedding 32 mm dia G.I. pipe (medium class) in pole collar/ foundation (during casting)/PCC /Hard standing/drain line cutting for cable entry including bending the pipe to the required shape complete with making good distrurbed surfaces of walls, floors etc complete all as specified & directed. 2.28 S&F 25mm outer dia Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified & directed. 2.29 S&F LED post top lantern 36 W with spun aluminium canopy and die cast aluminium spiget offer symetric light distribution with clear acrylic diffuser complete all as specified & directed. 2.3 Supply and fixing 100 A,16KA rating and breaking capacity and four pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc complete all as specified & directed. 2.31 Material and Labour for making connection of G.I. distribution branch with G.I. main of size upto 50 mm by providing and fixing tee, including cutting and threading the pipe etc. complete all as specified and directed. 2.32 Supply and fixing 25 mm dia nominal bore G.I. pipes medium grade complete with G.I. fittings including trenching and refilling etc complete all as specified and directed. 2.33 Supply and fixing 25 mm nominal bore gun metal gate valve with C.I. wheel head of approved quality (screwed end) complete all as specified and directed. 2.34 M&L for bituminous road cutting for passing of pipes and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri etc and labour required as per ground requirement complete all as specified and directed.; PVC/UPVC DOOR, WINDOW & CHOWKHAT (a) Factory made PVC, FRP shutters and frame (i) Duroplast Extrusion ii)M/S Sintex Industries Ltd iii)Durian iv)M/s Rajshri Plastiwood Ltd v) Fenesta vi) O M Industries (vii) Archid Ply (b) UPVC doors, windows, kitchen cabinets and ventilators, ceiling, wall paneling and dust cover i)H20 solution (ii) Aluplast (iii) Astral Limited (iv) Duroplast Extrusion (v) NCLVeka Limited (KPT) (vi) Prominence (c) Wood plastic composite (WPC) doors and frames i)Duroplast (ii) Ecoste (iii) Kumar Atrch Tech(Echon) (iv) Hardyplasty (v) Kalinga 2 WOODEN DOORS & WINDOW (a) Factory made Wooden Panel/Flush Doors & Windows shutter (i) Century doors (ii)Doorking Industrial Kolkata (iii)M/S Ambika Timber Works (iv)M/S Premier Wood Craft (P) Ltd (v)M/S Jain Doors Pvt Ltd 3 DOORS & WINDOW FITTINGS (a) Automatic Doors, Glass Fittings i)Toshi ii)Hardwin (b) Extruded Polished/ Matt Finish Brass Builders Hardware i)Harrison ii)Godrej (c) Aluminium Tower Bolt / Aldrops/Door Handle/Butt Hinges/Tower Rails (i) M/s Aluminium Udyog (Brand : GLOBAL ISI) (ii) Jindal (iii) Swastik (iv) RP Lock Co, New Delhi (v) ESSESS (vi) KICH (d) M/S Stove Enamelled butt hinges i)Mowjee ii)Crown iii)Everlite iv)Harrison v)Godrej (e) Floor Springs/Door Closers/Accessories i)Hardwin ii)Godrej iii)Spider (iv) IPSA door closer (v) Ozone door set (f) Mortice lock i)Harrison ii)Godrej iii)Dorset India (iv) Jainson(v)E-NOX (g) Drapery rod (i) Vista Levolor (ii) MAC-DÉCOR (iii) DECO window (iv)Jayesh Metal Corpn(JEC) (h) Venetian Blinds (i) Vista Levolor (ii) Aerolux (iii) MAC (iv) Classic Blinds 3A ROOF COVERING (a) Pre-painted galvalume/Galvanized corrugated steel sheets i) JSW Colourn plus ii) Tata Bluescope steel iii) Lloyd Insulation iv) Tata steel BSL v) Kirby Building Solution(I) Ltd (b) Non asbestos fibre reinforced(polypropylene)/6mm i)Everest Industries Ltd(EVEREST) ii) Charminarthick cement corrugated sheet iii) Ramco (c) CRCA steel sheet i)JSW MI ii) JSW steel iii) Tata steel (iv) Nezone 4 FALSE CEILING &PARTITION PANELING (a) PVC False Ceiling and Hollow Profile i)Kumar Arch Tech Pvt ii) Accura iii) Rajshri Plastiwood iv) Saint Gobain v) Modiguard (b) Perforated particle board/tiles for insulation and acoustic (i) Anchor ceiling tiles ii)Armstrong iiiAnutone iv) Kitply ceiling tiles (c) Seamless False Ceiling i)Anutone ii) Armstrong iii) Saint Gobain Gyproc v) Diamond ceiling vi) Ramco Hilux (d) UPVC ceiling and paneling i)Yashashri Polyextusion Ltd (e) False ceiling member(Perimeter, Ceiling section, Intermediates, Angles etc) (i) Armstrong ii) Saint Gobain iii) Ramco Hilux iv) Gypframe steel (f) Particle board/fibre cement board i) NCL Industries Ltd(NCL) ii) Everest Industries Ltd(EVEREST) iii) Hyderabad Industries Ltd(HIL) (g) Laminated sheet (i) Formica ii) Sun Gloss iii) Sunmica iv) Green Lam v) Novapan (h) Thermal/Acoustic Insulation(Nitrile rubber) & insulation covering system/Accoustics panels (i) Lloyd Insulation ii) Armacell India Pvt Ltd (ARMAFLEX) iii) Rock wool India Pvt Ltd (i) Adhesive i)Pidilite ii) Fevicol iii) Araldite(iv) Vamicol 5 CUPBOARDS,CABINETS &WARDROBE (a) PVC Kitchen (Cupboards,Cabinet & Wardrobes) (i) Kumar Arch Tech Pvt Ltd ii) Rajshri Plastiwood iii) Sintex iv) Commander 6 PVC,GALVANIZED SHEET,PANELLING,PARTITON,HUTS & BATHROOMS (a) Rigid Foam PVC Sheets From 0.50 mm Thickness To 40 mm Thickness i)Kumar Arch Tech Pvt Ltd ii)Sintex iii)Rajshri Plastiwood iv)Marino (b) Prelaminated PVC Sheets From 0.50 mm Thickness To 40mm Thickness i)Jain Irrigation System Ltd ii)Rajshri Plastiwood (c) Prefabricated PVC Hut & Bathrooms i)Kumar Arch Tech Pvt. Ltd ii)Prestar (d) Galvanized Colour/ Powder Coated Steel Windows, Doors, Partition And Structural Glazing i)NCL Altek & Seccolor Ltd. (e) Aluminium Composite Panel i)Alstone ii) Aluco bond iii) Viva iv) Aludecorv) Alstrong (f) Calcium Silicate Partition 1)Ramco Industries Ltd. (g) Polycarbonate Sheets i)Prestar Infrastructure Pvt Ltd ii)GE .... more in document
