Tender For Various Civil Work At Shanidham Ground In Pra. No. 35. - Excavation For Catch / Side Water Gutter In Soft Rock Strata To The Specified Section Including Stacking The Excavated Stuff In A Regular Bund And Disposing Of Unsuitable Or Excess Stuff , nagpur-Maharashtra

Various Civil Work At Shanidham Ground In Pra. No. 35. - Excavation for catch / side water gutter in Soft rock strata to the specified section including stacking the excavated stuff in a regular bund and disposing of unsuitable or excess stuff as directed. 2 Providing soling using 80 mm size granite / quartzite / gneiss / trap metal in 15 cm. layer including hand packing filling voids with sand / grit, ramming, watering complete. 3 Providingandlayinginsitu/readymixcementconcreteofM-10proportionwithtrap/ granite/ quartzite/ gneiss metal in foundation including necessary form work, compacting and curing etc. complete. (with reversible drum type mixer with SCADA with fine agreegates of required specifications ( VSI sand finely washed etc ) 4 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-20oftrap/granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or asdirectedincludingsteelcentering,formwork,coverblocks,laying/pumping, compactionandrougheningthesurfaceifspecialfinishistobeprovidedandcuringetc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 5 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters forR.C.C.pilecaps,footings,foundations,slabs,beamscolumns,canopies,staircase,newels, chajjas,lintelspardis,copings,fins,archesetc.asperdetaileddesigns,drawingsand schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 6 Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top andbottom of 25 x 25 x 5 mm size andvertical M.S. flat 35 x 5 mm and25 x 5mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete. 7 Providing and laying in situ / ready mix M20 RCC of trap/ granite/ quartzite/ gneiss metal for RCCworkofballastwalls,kerbsandboxreturnsincludingscaffolding,compaction, formwork finishing and curing etc. complete. (excluding reinforcement, with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant / pan mixer with fine agreegates of required specifications ( VSI sand finely washed etc ) 8 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-20oftrap/granite/ quartzite/ gneiss metal for R.C.C.slabs andlandingsasper detaileddesigns anddrawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 9 Providing and fixing precast 80 mm thick RCC Cover in M-30 for man holes of various sizes with reinforcement of 10 mm dia both way tied with tack welding @ 150 mm c/c with 2 hooks of 12 mm dia bars etc.complete. 10 Excavationforroadwayinearth,soilofallsorts,sand,gravelorsoftmurumincluding dressing section to the required grade, camber and side slopes and conveying the excavated materialswithallliftsuptoaleadof50m.andspreadingforembankmentorstackingasdirected. 11 ProvidingandfixingheavydutyinterlockingconcreteRUBBERMOULDGLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaningetc. complete. (using 100% crushed sand) 12 GARDEN SOIL:-Supplying on site garden soil well sieved 80 % to pass through I.S. sieve of 10 mm size free from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry. The color of the soil generally is red. The soil will be measured by measuring box. (Farma)Item includes Transporting, loading -unloading etc (.Lead charges per 25 km. considered Excluding royalty.) 13 Providing fabricating and erecting C1. Benches of 1.5n length fabricated with 40 x 20 mm M.S hollow pipe ( l6guage) 5 Nos. for seat framed 1. Sm |length and 40x 20 mm M.S. hollow Pipe (16 guage) 5 Nos for back framer (1.5 length) at equal spacing Handest & footerst complete casr iron |mounlded pandel ( Wt. 17 Kg apprx per panel ) & one coat primer & two coat oil pant Best Quality etc. Benche Size 1.5m x 0.45 x 0.45m back support ht 0.45 As per photo grophs and deciom etc. comm 14 Providing and applying white-wash in one coat on old / new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming downetc. complete. 15 Providing and applying three coats of water proof cement paint of approved manufacture and of approved colour tonew plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete. 16 Providing and applying two coats of lead/zinc base oil paint/bituminous paint of approved colourandshadetonewwoodworkandfiberboardsincludingpreparingthesurface, knotting, scaffolding if necessary, excluding primer coat etc. complete. 17 AIR WALKER/STORME RAMBBLERAREA: - 1.06Mtr x 0.81Mtr.SAFE AREA: - 1.72Mtr x 1.06Mtr.Providing and fixing Air Walker made from “B” class G.I. Pipe.The main frame of Ø60mm made from “C” Class G.I. pipe, andThe bottom support of M.S. round plate of Ø250 mm & 10mm thickness iswelded at bottom.The leg movement frame is of Ø40mm made from “C” Class G.I. pipe.The handle frame is of Ø32mm made from “C” Class G.I. pipe.The foundation used for fixing is consists of three equal items i.e. 90mmmade from “C” Class G.I. pipe, M.S. Round Plate of Ø250 mm & 10mmthickness & 25 mm X 25mm M.S. angle of 3 mm thickness.The footrests is made from FRP/C.I./Aluminum casting material, its sizes are130mm X 310mm X 5mm.For the support 50 X 50mm X 2mm CRC squarepipe is used.Closing Caps made from top quality FRP material with 2 mm thickness.The pins used are made up of Ø 25mm bright bar.The bearings used are “6205zz” permanent lubricated sealed bearing ofreputed make (SKF/FAG).High tensile steel with galvanized nut bolts are used for assembly.The serclips used for assembly are of Ø25 mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70micron thickness. 18 CHEST PRESS/BUTTERFLY MACHINEAREA: - 0.71Mtr x 1.72Mtr.SAFE AREA: - 0.86Mtr x 2.48Mtr.Providing and fixing chest press made from “B” Class G.I. pipe.The center pipe is of Ø115mm made from “C” Class G.I. pipe, andThe bottom support of M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom.The remaining frame is made up of Ø40mm“C” class G.I. pipe.The handle frame is made up of Ø32mm “C” class G.I. pipe .For the assembly different bushes are used which is made from 50mm with 3mm thicknessseamless pipe & 50mm solid bar is used.The foundation used for fixing is consists of three equal items i.e. Ø115mm made from “C” ClassG.I. pipe, M.S. Round plate of Ø250 mm & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle.The seats is fitted on the outer frame is made up of high quality FRP material of size 330 mm X300 mm of thickness 3 mm & M.S. Plate of thickness 5 mm and Size 250 mm X 200 mm is usedto Support it.Closing Caps are made from top quality FRP material which is of 2 mm thickness.The pins used are made up of Ø25 mm & Ø17mm solid bar.The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputedmake (FAG/SKF).High tensile steel with galvanized nut bolts are used for assembly.The serclips used for assembly is made up of Ø25 mm & Ø17mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micron thickness 19 ROWERArea:- 1.2 x 1Mtr.Safe Area:- 1.5 x 1.5Mtr.Providing and fixing rower made from “B” Class G.I. Pipe.The Main frame is of 80mm X 40mm & 40mm X 40mm CRC Pipe with 2 mm thickness.The handle frame is of Ø32made from “C” class G.I. pipe.The Foundation used for Fixing consists of three equal items i.e. Ø40mm made from “C”Class G.I. pipe, C channel of 75mm X 40mm X5mm & 25mm X 25mm X 3mm M.S. angle.To join the movement frame to main frame seamless pipe of Ø50mm & 3mm thicknessis used.The seats which are fitted on the main frame is made up of high quality FRP material ofsize 330mm X 300mm of thickness 3 mm & M.S. plate of size 250mm X 200mm X 5mm isused to support it.Closing caps are made from top quality FRP material which is of 2 mm thickness.The pins used are made up of Ø17mm hardened bright bar.The bearings used are of “6203zz” permanent lubricated sealed bearing of reputedmake (FAG/SKF).The handles used are of Rubber grip.High tensile steel with galvanized nut bolts are used for assembly.The bushes (Stopper) used to avoid the collusion.The serclips used for assembly is of Ø17 mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micronthickness. 20 SEATING & STANDING TWISTERAREA: - 1.7 x 0.66Mtr.SAFE AREA: - 2 x 1Mtr.Providing and fixing Seating & Standing Twister made from “B” Class Galvanized Iron (G.I.) Pipe.The Center Pipe is of Ø100mm made from “C” Class G.I. Round Pipe, and The bottom support of M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom.The standing frame of the Seating & Standing twister is of Ø40mm, Ø60mm, and Ø50mm made from “C” class G.I. pipe.The handle frame of Seating & Standing twister is Ø32 mm & Foot resting frame of seating side is made from “C” class G.I. pipe of Ø25mm & Ø 32mm. The seamless pipe is used for joining the centre pipe frame & handle frame is made from Ø130mm with 3mm thickness.The foundation used for fixing is consists of three equal items i.e. Ø 90mm made from “C” class G.I. pipe, M.S. round plate of Ø250 mm & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle.The standing plate is fitted on the standing frame is made up of Ø 100mm seamless pipe & Seating plate is fitted on the frame is made up of Ø 60mm seamless pipe. Ø300mm x 10mmThikness M.S. Round Plate. Closing caps made from top quality FRP material which is of 2 mm thickness. The Pins used are made up of Ø 25 mm bright bar.The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed make (FAG/SKF).High tensile steel with galvanized nut bolts are used for assembly.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micron thickness. 21 SEATING & STANDING TWISTERAREA: - 1.7 x 0.66Mtr.SAFE AREA: - 2 x 1Mtr.Providing and fixing Seating & Standing Twister made from “B” Class Galvanized Iron (G.I.) Pipe.The Center Pipe is of Ø100mm made from “C” Class G.I. Round Pipe, and The bottom support of M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom.The standing frame of the Seating & Standing twister is of Ø40mm, Ø60mm, and Ø50mm made from “C” class G.I. pipe.The handle frame of Seating & Standing twister is Ø32 mm & Foot resting frame of seating side is made from “C” class G.I. pipe of Ø25mm & Ø 32mm. The seamless pipe is used for joining the centre pipe frame & handle frame is made from Ø130mm with 3mm thickness.The foundation used for fixing is consists of three equal items i.e. Ø 90mm made from “C” class G.I. pipe, M.S. round plate of Ø250 mm & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle.The standing plate is fitted on the standing frame is made up of Ø 100mm seamless pipe & Seating plate is fitted on the frame is made up of Ø 60mm seamless pipe. Ø300mm x 10mmThikness M.S. Round Plate. Closing caps made from top quality FRP material which is of 2 mm thickness. The Pins used are made up of Ø 25 mm bright bar.The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed make (FAG/SKF).High tensile steel with galvanized nut bolts are used for assembly.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micron thickness. 22 SIT UP BOARD/SEATED PANELArea:-0.50 x 1.70 Mtr.Safe Area:- 0.86 x 2 Mtr.Providing and fixing Sit up Board made from “B” Class G.I.pipe.The main frame is of Ø40mm & Ø32mm made from “C”Class G.I. pipe.Perforated sheet of 1.5mm thickness is welded on 25 x3mm thick flat Patti on main frame.The base side of the sit up board is made of 50 x 20 mmCRC pipe.The powder coat is done by Poly urethane & Epoxypowder with 60 to 70 micron thickness 23 SURF BOARD /WAVE PANELArea:- 0.91 x 0.86Mtr.Safe Area:- 1.39 x 1.27Mtr.Providing and fixing Surf Board made from “B” Class G.I. pipe.The center pipe is of Ø115mm made from “C” class G.I. pipe, andThe bottom support of M.S. plate of Ø 250 mm & 10mm thickness iswelded at bottom.The handle frame is of Ø 40mm made from “C” class G.I. pipe.The foundation used for fixing consists of three equal items i.e. Ø 90mm made from “C” Class G.I. pipe, M.S. round plate of Ø250 mm & 10mmthickness, 25mm X 25mm X 3mm M.S. angle.To join the centre pipe & handle frame seamless pipe of Ø130mm & 3mm thickness is used.For the movement, bushes are used Ø60mm with 3mm thickness &Ø60mm solid bar is used.The footrests is made from Aluminum casting material, its sizes are 320 mm X 270 mm & 5 mm thickness.For support of footrest is 200mm X 250mm with 5mm thickness M.S. Plate and 50mm X 50mm CRC Square pipe with 2mm thickness is used.Closing Caps made from top quality FRP material which is of 2 mmthickness.The pins used are made up of Ø25 mm bright bar.The bearing used are of “6205zz” permanent lubricated sealed bearing of reputed make (FAG/SKF).The handles used are of Rubber grip.High tensile steel with galvanized nut bolts are used for assembly.The bushes (Stopper) used to avoid the collusion made from Poly Urethin Plastic material of Ø 50 mm.The serclips used for assembly is of Ø25 mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micron thickness. 24 SKY WALKER/ AREA: -1.72Mtr x 0.63Mtr.SAFE AREA: - 2.54Mtr x 1Mtr.Providing and fixing Sky Walker made from “B” class G.I. Pipe.The main frame pipe is Ø80mm made from “C” Class G.I. pipe.The outer ring of sky walker is Ø32mm made from “C” Class G.I. pipe.For connecting the handle frame to main pipe Ø60mm “C” Class G.I. pipe is used.The bottom support of M.S. round plate of Ø250 mm x 10mm thickness is welded atbottom.The leg movement frame is of 50 x 50mm x 2mm thick CRC square pipe.The handle frame is of Ø40mm made from “C” Class G.I. pipe.The foundation used for fixing is 80 x 40mm x 3mm thickness C-Channel.The footrests is made from Aluminum casting material, its sizes are 130 X 310 X5mm.Closing Caps made from top quality FRP material with 2 mm thickness & Plastic cap areused.The pins used are made up of Ø 25mm bright bar.The bearings used are “6205zz” & “6203zz” permanent lubricated sealed bearing ofreputed make (SKF/FAG).High tensile steel with galvanized nut bolts are used for assembly.The serclips used for assembly are of Ø25 mm.The powder coat is done by Poly urethane & Epoxy powder with 60 to 70 micronthickness. 25 LEG PRESSArea:- 0.40 x 1.77Safe Area:- 1 x 2.38Mtr.Providing and fixing Leg Press made from “B”Class G.I.PipeThe center pipe is of Ø115mm made from “C” Class G.I.The bottom support of M.S Round plate of Ø250mm & 19 MM.thickness is weldedThe remaining outer frame of Ø40mm made from “C” class G.Ipipe.The foundation used for fixing is consist of three equal item i.eØ80mm made from “C” class G.I. pipe, M.S. Round plate of Ø250mm& 10mm thickness, 25 mm X 25mm x3mm M.S angle.To join the centre pipe &outer frame seamless pipe of Ø120 mm &3mm thickness is used.The seats are fitted on the outer frame is made up of FRP material of size 330 mm X 300 mm of thickness 3 mm & M.S. Plate ofmm and Size 250 mm X 200 mm thickness 5. mm and Size 250 mm X 200 mm is used to support it.The footrests is made from Aluminum casting material, its sizes are130 mm X 310 mm & 5 mm thickness.The frame of footrests consists of Ø32mm made from “C” class G.I.pipeClosing caps made from top quality FRP material which is of 2 mm thickness.The inner bushes is made from seamless pipe, its diameter is 60 mm & 5 mm thickness.The pins used in are made up of Ø25 mm hardened bright bar.The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed make (FAG/SKF).The handles used are of Rubber grip.High tensile steel with galvanized nut bolts are used for assembly.The serclips used for assembly are of Ø25 mm.The powder coat is done by Poly rethane & Epoxy powder with 60 to 70 micron thickness. 26 Transportation of Material obtained from debries of various sorts including necessary excavation / loosing including loading,unloading and conveying

INR 590 /-

Refer document