Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Excavation in trenches n exc 1.5m in depth and 1.5m in widthand getting out in soft/loose soil for foundation or laying of cable complete all as specifiedand as directed. |
| 2 | Returning, filling in, including spreading, levelling, watering and wellramming in layers not exc 25cm in soft/loose soil complete all as specifiedand as directed. |
| 3 | Removing excavated material (soil)n. exc 50m and deposited where directed at a level n exc. 1.5m above the starting point complete all as specifiedand as directed. |
| 4 | Surface dressing n. exc 15cm deep and getting out in soft and loose soil complete all as specifiedand as directed. |
| 5 | Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance n.exc 50m & making good surface complete all as specifiedand as directed. |
| 6 | M&L for providing cement concrete (1:4:8) type D2 (using 40mm graded stone aggregates) as in foundation, mass concrete and filiings complete all as specifiedand as directed. |
| 7 | M&L for cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in anchorage blocks for hold fast, post and struts complete all as specifiedand as directed. |
| 8 | Use and waste of form work for rough finished surfaces of concrete to side of concrete in founddation, footing base, base of columns, side and soffits of plinth beam and simillar work complete all as specifiedand as directed. |
| 9 | M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in footing, foundation, beams, plinth beams, base for columns and mass concreteetc complete all as specifiedand as directed. |
| 10 | Use and waste of form work for rough finished surfaces of concrete to side of columns and simillar work complete all as specifiedand as directed. |
| 11 | M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in columns and pillars etc complete all as specifiedand as directed. |
| 12 | Use and waste of form work for rough finished surfaces of concrete to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, and simillar work complete all as specifiedand as directed. |
| 13 | M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span concreteetc complete all as specifiedand as directed. |
| 14 | Use and waste of form work for rough finished surfaces of concreteto soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specifiedand as directed. |
| 15 | Use and waste of form work for rough finished surfaces of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specifiedand as directed. |
| 16 | M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate)as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specifiedand as directed. |
| 17 | Use and waste of form work for rough finished surfaces of concrete tochullah hoods, chajjas, troughs and simlar items including edges complete all as specifiedand as directed. |
| 18 | M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate)as inchajjascomplete all as specifiedand as directed. |
| 19 | S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requred, including cranking, bending spirally and binding with mild steel (annealed) wire not less than 0.90mm dia complete all as specifiedand as directed. |
| 20 | S&F mild steel TMT bars 8 to 10 mmdia a as in stirrups, spacers and binders complete all as specifiedand as directed. |
| 21 | M&L for brick work with sub class \"B\" old size kiln burnt bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specifie and as directed. |
| 22 | M&L for brick work with sub class \"B\" old size kiln burnt bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specifie and as directed. |
| 23 | M&L for 10mm thick rendering incementmortar (1:6) onfairfacesofbrickworkorconcretesurfaces,finishedevenandsmooth without using extra cement asonwall complete all as specifie and as directed. |
| 24 | M&L for 15 mm thick cementplaster in two layers i.e - 1st layer 10mm thickin CM (1:4) and 2nd layer 5mm thick in CM (1:4) using WPCas per manufacturer\"s instructions on fair faces of brick work or concrete surfaces andfinishedeven and fair complete all as specified and as directed. |
| 25 | Suppy only integral water proofing compound complete all as specified and as directed. |
| 26 | M&Lfor5mm thickcement plater in cement mortar (1:3)as on ceiling and surface finished even & smooth without using extra cement complete all as specified and as directed. |
| 27 | M&L for preparationof new plasteredsurfaces of wall and applying twocoatsof white wash with andincluding necessary scaffolding etc. complete all as specified and as directed. |
| 28 | M&L for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying three coats of white wash complete all as specified and as directed. |
| 29 | M&L for preparation of new plastered surface of walls, chhajjas, soffits & beamincluding necessary scaffolding and applying two coats of cement base paint over one coat of chalk whitingprimer complete all as specified and as directed. |
| 30 | M&L for complete removal of existing surface of walls, chajjas, soffits & beamincluding necessary scaffolding and applyingtwo coats of cement base paint over one coat of chalk whitingprimer complete all as specified and as directed. |
| 31 | M&L for brokenstone orboulders hardcore of gauge n. exc. 63mm deposited,spread and levelled in layers n. exc 15cm thick watered and rammed to a true surface for plinth protection/path complete all as specified and as directed. |
| 32 | M&L for 75mm thick cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base to floors complete all as specified and as directed. |
| 33 | M&L for25mm thick PCC (1:2:4), type B1, (using 20mm graded stone aggregate) as in sub floorcomplete all as specified and as directed. |
| 34 | M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular)area of each tile n. exc. 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 35 | M&L for joint free coloured glazed ceramic tiles in vertical surfaces of size (300x200)mm x 7mm thick/ (450x300)mm x 7mm thick, set and jointed in cement slurry and pointed in white or coloured cement to match laid over & including 10mm thick cement rendering in cement mortar (1:4) complete all as specified and as directed. |
| 36 | M&L for 20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and inncluding over 15mm thick screed bed or bedding layer of cement mortar (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. |
| 37 | M&L for providing precast cement concrete landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves, platform and similar articles with plain faces type B-1 (1:2:4) (using 20 mm graded stone aggregate) set in CM (1:4) complete all as specified and as directed. |
| 38 | M&L for 75 mm thick cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and as directed. |
| 39 | M&Lprecast cement concrete louvres and jallies 40 mm thick in (1:2:4) type B-0 (using 12.5mm graded stone aggregate) including all mouldings but excluding frame and set in cement mortar (1:6) complete all as specified and as directed. |
| 40 | S&Ffactory made PVC door frame of size (50mmx47mm) made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing complete all as specified and as directed. |
| 41 | S&F factory made solid PVC moulded door shutters with wood free EPS 28 to 30 mm thick (stile), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colourPVC sheet on back face, supplying & fixing in frame at site as per specification & drawing. |
| 42 | S&F butt hinges, stainless steel,ISI Marked 100mm size, complete all as specified and as directed. |
| 43 | S&F extruded aluminium alloy handles, fabricated type anodised of 125mm long complete all as specifed and as directed. |
| 44 | S&F aluminium anodised barrel tower bolts of extruded section and fixed of 100mm long complete all as specifed and as directed. |
| 45 | M&L for 4.0 mm thick frosted sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in eachpane complete all as specifed and as directed. |
| 46 | S&F powder coated aluminium frame for doors, windows, ventilators, partations with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. |
| 47 | S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type (B-21) 100mm long (2 no.), suitable handle (1 no.) complete all as specified and as directed. |
| 48 | S&F powder coatedaluminium two track sliding type glazed window shutter with 4 mm thick frosted sheet glass fixed open track section (100x38x1.5)mm having two track (two of glass) with members of window shutters of section (38x12x1.5)mm and other standard sliding section including all necessary fiber wheel rollers suitable handles to facilitate sliding and all necessary jointing cleats, glazing clips, rubber packing, aluminium snap beading etc complete all as specified and as directed.Note:-Cost of other consumables required for the item viz Glass panes / lock /handle etc shall be deemed to be included in the quoted rate. |
| 49 | S&F aluminum anodised grill DG-102 (10mm x 5.2mm) of decorative grill or equivalent fixed with \"F\" Section size not less than (20.60x15.20)mm x 1.5mm thick of approved make complete all as specified and as directed. Note:- Minimum thickness of anodizing shall be 15 microns. |
| 50 | S&F PVC connection 15mm size, 600mm long with PTMT nuts both side complete all as specifed and as directed. |
| 51 | S&F brass CP towel rail 600 mm long of, fixed with and including chromium plated screws on walls, complete all as specified and as directed. Make:- Prayag Cat No BA-01 or equivalent as per list of make and approved by the GE. |
| 52 | S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered white colour, hoisted and fixed in position complete all as specified in SSR Part I. |
| 53 | S&F ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of size 20mm dia complete all as specifed and directed. |
| 54 | S& F 15mm bore Gun metalglobe or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe or for union and fixed complete all as specifed and as directed. |
| 55 | S&FVitreous China, Ist quality, Half Stall Urinal, White, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, provision of brass chromium plated spreader suitable for 15mm bore pipe, provision of 40mm bore PVC waste pipe, complete all as specified and directed. |
| 56 | S&F vitreous china squatting pan, \"Orissa\"pattern, size (580 X 440)mm white with integral foot rests, including connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint and to socket or stopper, including flush pipe all fittings etc complete all as specified and directed |
| 57 | S&F vitreous china wash down water closet pan “Pedestal Pattern” colouredwith white WC seat cover closed pattern with flat bottom and mild steel chromium plated or aluminized hingingdevice including PVC flush pipe and joints etc and connection to drain, flushing pipe, anti-syphonagepipe, and fixing arrangements with fixing bolts etc complete all as specified and as directed. |
| 58 | supply and fixinglow level flushing cistern 10 ltrs capacity, and connections to pies an fixing of chain and pull, or lever, if any PVC valveless, syphonic action type, flushing cistern, low level, white,with inlet, including brackets all as specified. |
| 59 | S&F vitreous china counter type wash hand basin ovalshape of size (420 x 420 x 135)mm fixed on granite counter down slab including brass chromium plated full threaded waste coupling with grating 32mm dia PVC waste pipe complete all as specified and as directed. Note:- Granite slab, RCC plat form, brick wall supportetc shall be measured and paid separately. |
| 60 | S&Fvitreous china ware wash hand basin, white, flat back of size (550 x 400) mm including brackets, cutting for and pinning in ends of brackets or erecting stand including brass CP union/waste fittings of 32mm dia and discharge pipe of 32mm dia PVC of 1.0 m length etc complete all as specified and as directed. |
| 61 | S&Fbib taps fancy type chromium plated, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed suitable for 15mm bore pipe complete all as specifed and as directed. |
| 62 | S&F pillar cock fancy type cast copper alloy, chromium plated suitable for 15mm dia bore complete all as specifed and as directed. |
| 63 | S&F stop cock fancy type chromium plated, (concealed type) screwed down, high presure with crutch or butterfly handle screwed both ends suitable for iron pipe of 15mm bore pipe complete all as specifed and as directed. |
| 64 | S&F15 mm angle valve chromium plated with wall flangeand fancy typewithhigh pressure screwed down and with CP flange complete all as specified and as directed. |
| 65 | M&L for 15mm GI tubing \"medium grade\" with all GI fittings and fixed complete to wall and celing or laid in floor complete all as specifed and as directed. |
| 66 | M&L for 20mm GI tubing \"medium grade\" with all GI fittings and fixed complete to wall and celing or laid in floor complete all as specifed and as directed. |
| 67 | M&L for cast iron nahani trap / floor trap with CP grating including jointing with cement joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all as specified and as directed. |
| 68 | S&F Cast Iron \"P\" or`S\"trap 100mm bore complete all as specified and as directed. |
| 69 | S&F 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to wallsincluding suitable iron clamps after every one mtr of interval with cement joints fixed to wall complete all as specified and directed. |
| 70 | S&F 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to wallsincluding suitable iron clamps after every one mtr of interval with cement joints fixed to wall complete all as specified and as directed. |
| 71 | S&FCI 100mm bends with door complete all as specified and as directed. |
| 72 | S&F CI 100mm single branch piece with door complete all as specified and as directed. |
| 73 | S&F CI 100mm size double branch piece with door complete all as specified and as directed. |
| 74 | S&F CI 75mm size bends with door complete all as specified and as directed. |
| 75 | S&F cast iron cowls 100 mm size complete all as specified and as directed. |
| 76 | M&L for 100 mm thick concrete bed to drain pipes in cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed. |
| 77 | M&L reinforced concrete pipes, class NP2, 150 mm bore, laid and jointed complete with collars complete all as specified and as directed. |
| 78 | M&L for salt-glazed stoneware gully traps, square mouthed floor trap, of size (100x 100)mm complete all as specifed and as directed. |
| 79 | M&L for preparation of plastered/concrete surfaces ofroof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:-(a) Plastering 10mm thick in cement mortar (1:4) on concrete surfaces using WPC @3% by weight of cement, finished even and smooth(b) Surface shall be throroughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface.(c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consistingof a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc.(d) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flame. |
| 80 | Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) 150 mm internal dia set in cement mortar complete all as specified and as directed. |
| 81 | Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc of any description including removing debrish from site complete all as specified and as directed. |
| 82 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premices complete all as specified and as directed. |
| 83 | S&F mild steel work (FE 290Grade E-165) as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) includingdistance pieces, cleats etc. complete all as specified and as directed. |
| 84 | M&L for mild steel works (Fe-290 Grade E-165) as in posts and struts etc in fencing of angle or other sections, including cutting tops to shape as directed, drilling holes, notching for wire etc, comlete all as specified and as directed. |
| 85 | S&F MS steel work in tubular trusses and tubular posts including special shaped washersetc., complete using butt welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and as directed. |
| 86 | S&F hard drawn steel wire fabric cut to length, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement (not exceedding 4kg) complete all as specified and as directed. |
| 87 | M&L for cutting into existing manholes 150mm dia pipe for connecting new drains, making good to pipe and rendering, cutting out existing benching for and formating branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregates) surface finished smooth and reforming beching as required complete all as specified and as directed. |
| 88 | M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 89 | S&F 18/19mm thick prelaminated partcile boardboth sides, interior grade, of approved shade and pattern fixed with screws to timber frame for cupboard and shelves and all necessaryfittings (hinges, screws, beading, hasp & staple), complete all as specified and as directed. |
| 90 | S&F machine pressed precast concrete interlocking paver block any shape and size, with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade with and including laid over 50 mm thick sand cushioning complete all as specified and as directed. |
| 91 | M&L for pre polished chequeredcement concrete tiles of size (30x30)cm x 25mm thick, set and jointed with grey cement anndd pointed with neat cement slurry with grey cement and pigment as in floors with and including15mm thick screed bed CM (1:4) complete all as specified and as directed. |
| 92 | M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in surface channel, drain and manholes complete all as specified and as directed. |
| 93 | M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in benching, coping including necessary use and waste of form work complete all as specified and as directed. |
| 94 | S& F 5mm thick glass mirror of size (750x600)mm all edges/ border moulding complete all as specified and as directed. |
| 95 | M&L for cutting openings, through brick walls in mud mortar for door, window and other openings or enlarging existing openings converting window into door openings, etc. or cutting out effective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m complete all as specified and as directed. |
| 96 | S&F in repairsvitreous china squatting pan, \"Orissa\"pattern, size (580 X 440)mm white with integral foot rests, including connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint and to socket or stopper, including flush pipe all fittings etc complete all as specified and as directed. |
| 97 | S&F in repairs vitreous china wash down water closet pan “Pedestal Pattern” colouredwith white WC seat cover closed pattern with flat bottom and mild steel chromium plated or aluminized hingingdevice including PVC flush pipe and joints etc and connection to drain, flushing pipe, anti-syphonagepipe, and fixing arrangements with fixing bolts etc complete all as specified and as directed. |
| 98 | S&F in repairs low level flushing cistern 10 ltrs capacity, and connections to pipes and fixing of chain and pull, or lever, if any PVC valveless, syphonic action type, complete all as specified and as directed. |
| 99 | S&F in repairs vitreous china wash hand basin, white, flat back of size (550 x 400)mm including brackets, cutting for and pinning in ends of brackets or erecting stand including brass CP union/waste fitting of 32mm dia and discharge pipe of 32mm dia PVC of 1.0 m length, cast copper alloy with all fittings etc complete all as specified and as directed. |
| 100 | S&F in repairsstop valve (half turn)15 mm dia cast copper alloy chromium plated fancy type high pressure with crutch or butter fly handle screwd for iron pipe or union and fixed complete all as specified and as directed. |
| 101 | S&F in repairsbib tap (half turn)15 mm dia cast copper alloy chromium platedfancy type with crutch or butter fly handle screwed for iron pipe or for brass ferrulecomplete all as specified and as directed. |
| 102 | S&F pillar tap (half turn) 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure with or without lettered Hot or Cold with scrwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 103 | S&F in repairs for PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed. |
| 104 | S&F hand shower (Health faucet) with 1.00 metre long Easy flex tube in chrome finish & wall Hook complete all as specified and as directed. Make:- Cat No ALD-CHR-565 of JAQUAR or equivalent of make MARC or KOHLER as approved by the GE. |
| 105 | S &F pre paintedgalvalume aluminiumzinc coatingGI basedcorrugatedsteel sheet0.50 mmthickof ancolourhavingtensilestrengthof 550Mpa as in roof covering/cladding to fix the wall fixed with self taping screwscomplete all as specified and as directed. |
| 106 | Taking down chowkhat or frame with shutters (without taking off shutter from the frame) area n exc. 1.5 sqm each complete all as specified and as directed. |
| 107 | M&L for preparationof new plasteredsurfaces of wall and applying twocoatsof oil bound distemper over a coat of primer with andincluding necessary scaffolding etc. complete all as specified and as directed. |
| 108 | M&L for cement concrete (1:5:10) type E2 (using 40mm graded crushed stone aggregate) as in foundations, mass concrete and filling in sunken floor etc complete all as specified and as directed. |
| 109 | M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages :Stage 1:Providing 15mm thick plaster in CM (1:3) mixed withwater proofing chemical of Dr.Fixit or Shalicrete \"R\" of STP Ltd in the proportion/quantity all as per manufacturer\"s instructions.State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces.Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer\"s instructions.Stage 4:Laying fyber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky.Stage 5:After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer\"s instructions.Stage 6:Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer\"s instructions.Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i)Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid. |
| 110 | Taking down shutter of any description exceeding area 1 sqm and not exc 2 sqm each complete all as specified and as directed. |
| 111 | Taking down cement plaster or cement lime plasteron brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed. |
| 112 | Dismantling of structural steel work including door, gates but excluding framed truss etc. complete all as specified and as directed. |
| 113 | S&F in repair looking mirror of size (600x450)mm, bevelled edges of selected quality glass, mounted on 6mm thick commercial ply or AC plain building board with aluminium frame around and fixed to wooden plugs with CP brass screws etc complete all as specified and as directed. |
| 114 | S&F in repair Vitreous China, Ist quality, Half Stall Urinal, White, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, provision of brass chromium plated spreader suitable for 15mm bore pipe, provision of 40mm bore PVC waste pipe, complete all as specified and directed. |
| 115 | S &F pre paintedgalvalume aluminiumzinc coatingGI basedplainsteel sheet0.50 mmthickof ancolourhavingtensilestrengthof 550Mpa as in roof covering/cladding to fix the wall fixed with self taping screwscomplete all as specified and as directed. |
| 116 | M&L for 75mm thick cement concrete (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) as in floor with and including necessary form work complete all as specifiedand as directed. |
| 117 | M&L for cutting holes in brick walls exc half brick but not exc one brick thick in mud mortar for inserting holdfasts and makinng good the dismantled portion in cement concrete (1:2:4) type B1 (using 20mm graded stone aggregates) upto G+3 storey building for necessary scaffolding and safety arrangements complete all as specified and as directed. |
| 118 | S&F joist, channel, angle, or tee sections, fixed independently without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) including fixing of material upto G+3 storey building and necessary scaffolding and safety arrangements complete all as specified and as directed. (Fe 410-W Gde E 250 quality A) |
| 119 | Taking down carefully unserviceable copper/aluminium point wiring(light, fan, socket or power) complete including fixture and fitting such as switches, ceiling rose, lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DB’s, meter board any type complete all as specified and as directed. |
| 120 | M&L for point wiring with single core PVC insulatedbut unsheathed 1.5 Sqmm FRLS multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC conduit medium grade not less than 20 mm diaISI marked with all conduit fittings and fixing accessories including pressed steeI boxes with bakelite sheetfor mounting switches, sockets, fan regulators, etc and earth wire single core PVC insulatedbut unsheathed multistrand copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly complete all as specified and as directed by Engr- in- Charge. (a) One light point controlled by one switch one way |
| 121 | (b) One fan/exhaust fan point controlled by one switch. |
| 122 | (c) One socket outlet 5 Amp controlled by one switch on independent board |
| 123 | (d) One 3 pin 5 Amps socket out let point on the same board controlled by one switch complete |
| 124 | Description all as per Srl item No 120.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sqmmstranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and as directed. |
| 125 | Supply and fixing ceiling rose, surface type, 65mm x 50mm, 3 terminal complete all as specified and as directed. |
| 126 | Supply and fixing switch piano flush type 5 Amps, single pole one way complete, all as specified and as directed. |
| 127 | Supply and fixing socket out let 3 pin 5 Amps, flush type complete, all as specified and directed. |
| 128 | S&F switch piano flush type single pole one way15 Amps complete, all as specified and as directed. |
| 129 | Supply and fixing socket outlet 2 in 1, 6 pin 5/15 Amps, flush type complete all as specified and as directed. |
| 130 | S&F indoor decorative LED battens- integrated type 20 watt 4 feet white fixture suitable for LED tube 20 watt, bipin holder, connector block, LED rod 20 watt etc complete with all accessories internally are wired and including connecting up with twin core copper conductor cable complete all as specified and as directed. Make- Havells Cat No-LHEXACP7UN1W020 or equivalent as per lisst of makes. |
| 131 | Supply and fixing sheet metal enclosure for distribution board SPN (when MCBs to be used ) 8 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and as directed. |
| 132 | Supply and fixing MCB, SPN, 40 Amp ,10 kA breaking capacity complete all as specified and as directed. |
| 133 | Supply and fixing MCB, SP, 6-32 Amp,10 kA breaking capacity complete all as specified and as directed. |
| 134 | Supply and fixing lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. |
| 135 | Supply and fixing LED bulb 7 watt fixed in pendent holder / bulk head complete all as specified and as directed. |
| 136 | M&L in replacement of PVC insulated service cable flat or round sheathed, aluminium multistraned conductor 1100 volts grade of size 16 sqmm 2 core complete all as specified and as directed. |
| 137 | Supply, laying and testing of 15mm bore GI tubing \"medium grade\" with all GI fittings such as tees, bends, elbows, reducer, union, clamp etc and fixed complete to wall / laid in trenches / roof (with proper clamping arrangements) complete all as specifed and as directed. |
| 138 | Supply, laying and testing of 20mm bore GI tubing \"medium grade\" with all GI fittings such as tees, bends, elbows, reducer, union, clamp etc and fixed complete to wall / laid in trenches / roof (with proper clamping arrangements) complete all as specifed and as directed. |
| 139 | Supply, laying and testing of 25mm bore GI tubing \"medium grade\" with all GI fittings such as tees, bends, elbows, reducer, union, clamp etc and fixed complete to wall / laid in trenches / roof (with proper clamping arrangements) complete all as specifed and as directed. |
| 140 | S& F 15mm bore Gun metalglobe or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe or for union and fixed complete all as specifed and as directed. |
| 141 | S& F 20mm bore Gun metalglobe or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe or for union and fixed complete all as specifed and as directed. |
| 142 | S& F 25mm bore Gun metalglobe or gate valves ISI marked with iron wheel head, screwed both ends for iron pipe or for union and fixed complete all as specifed and as directed. |
| 143 | M&L for cutting / tapping the existing CI / DI / GI pipe line of 150 / 100 / 80 / 50 / 40mm dia bore in any position and reducing to required length for inserting of new Tee 150 x 150 x 100mm, branches including jointing with lead complete all as specified and as directed. |
| 144 | M&L for earthing complete for building with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI earth wire 4mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC (1:3:6) type C-1 (using 20mm graded stone aggregate), with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM (1:4), funnel with wire gauge mesh, 80 mm thick RCC pit cover (320mm x 320mm) of RCC (1:2:4) type B-1 (using 20 mm graded stone aggregates) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2020) and specified includingprovision of GI stripprotected by 15 mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, and including all excavation andearth work & connecting the earthing to an earthing test pointcomplete all as specified & as directed by Engr-in-Charge. |
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail