|
| 1 | Dismantling of floor, hearth or wall tiles including cement mortar bedding ( but not backing) and remvoing rubbish off the premises, complete all as specified and directed. |
| 2 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed. |
| 3 | M&L for joint free glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering back coat in CM (1:4), complete all as specified and directed. |
| 4 | M&L for glazed ceramic coloured tiles 7 to 8mm thick of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed. |
| 5 | Demoliton of cement concrete in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed. |
| 6 | M&L for 75mm thick PCC (1:2:4) type B- 2,(using 40mm graded crushed stone aggregate) for pavings or plinth protection etc., complete all as specified and directed. |
| 7 | M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade \"B\", thichness of slab n. exc. 100mm, complete all as specified and directed. |
| 8 | Demolition of reinforced cement concrete(reinforcement cut as required to facilate demolition) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. |
| 9 | Use & waste formwork to sides and soffits of floor or roof beams, beam haunching’s, girders, breastsummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. fair finish flat surfaces of formwork, complete all as specified and directed. |
| 10 | S & F mild steel TMT bars 6mm to 8mm dia (Grade Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia., or securing with clips, complete all as specified and directed. |
| 11 | M&L for RCC (nominal mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregrate) as in, slab cover, beams, cantilevers, bressummers, lintels etc., complete all as specified and directed. |
| 12 | Demolition of bricks work or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete aritcles, complete all as specified and directed. |
| 13 | M&L for brick work with sub class \"B\" brick,s old size, burnt clay bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:6), complete all as specified and directed. |
| 14 | M&L for brick work with sub class \"B\" bricks, old size, burnt clay bricks, straight or curved on plan, any radius, built in CM (1:4) in half brick thick, complete all as specified and directed. |
| 15 | Taking down cement plaster on brickor concrete surfaces including racking out joints, hacking for key, scrubbing downwith water etc, complete all as specified and directed.. |
| 16 | M&L for 10mm thick cement plaster on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth without using extra cement, complete all as specified and directed. |
| 17 | M&L for 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces in CM (1:4) and finished even and smooth without using extra cement, complete all as specified and directed. |
| 18 | M&L for preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty, complete all as specified and directed. |
| 19 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed. |
| 20 | M&L for complete removal of existing treatment ofwall surfaces and applying two coats of oil bound distemper over and including a coat of 2mm thick wall care putty, complete all as specified and directed. |
| 21 | M&L for preparation of old surfaces of ceilings and applying twocoats of white wash, complete all as specified and directed. |
| 22 | M&L for preparation of old painted wooden surfaces and applying one coat of synthetic enamel paint (1st grade quality) on surface of any description over 10cm width or girth not otherwise described, complete all as specified and directed. |
| 23 | M&L for preparation of old painted steel or iron surfaces and applying one coat of synthetic enamel paint (1st grade quality) on surface of any description over 10cm width or girth not otherwise described, complete all as specified and directed. |
| 24 | Taking down 15mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed. |
| 25 | Taking down 20mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed. |
| 26 | Taking down 25mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed. |
| 27 | Taking down 50mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed. |
| 28 | S&F CPVC pipe of size20mm dia, high pressure SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reduceretc. with necessary solvent cement, complete all as specified and directed. |
| 29 | S&F CPVC pipe of size25mm dia, high pressure SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reduceretc. with necessary solvent cement, complete all as specified and directed. |
| 30 | S&F CPVC pipe of size50mm dia, high pressure SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reduceretc. with necessary solvent cement, complete all as specified and directed. |
| 31 | S&F in repair 25mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed. |
| 32 | S&F in repair 50mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed. |
| 33 | S&F in repair vitreous china squatting pan,\"Orissa pattern\"white, size 580mm x 440mm with integral foot rest,\"P\" or \"S\" trap, including connection to trap, and to flushing pipe, anti -syphonage pipe etc., complete all as specified and directed. |
| 34 | S&F in repair 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with inlet ball valve, float and handle and connection to pipes, complete all as specified and directed. |
| 35 | S&F for 600mmx450mm bevelled edge mirror made of selected quality sheet glass not less than 5.5mm thick, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 36 | S&F in repair CP pillar tap, 15mm bore, fancy type, cast copper alloy, capstan head, chromium plated, screweddown high pressure with or without lettered “hot’ or “cold” with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed. |
| 37 | S&F in repair 15mm bore, fancy type, chromium plated, bib tap, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed bothends for iron pipe or union, complete all as specified and directed. |
| 38 | S&F in repair 15mm bore, fancy type, chromium plated, stop valves, with long shank and cup (concealed type) angular, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed bothends for iron pipe or union, complete all as specified and directed. |
| 39 | S&F in repair 15mm bore, two way bib tab (fancy type), chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed bothends for iron pipe or union, complete all as specified and directed. |
| 40 | S&F in repair 15mm bore angular vave, chromium plated, cast copper alloy, screwed down, high presure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed. |
| 41 | S&F in repair swivel shower rose 125mm size, brass, chromium plated for fixing with 15mm bore pipe, complete all as specified and directed. |
| 42 | S&F in repair CP shower arm 15mm size, 195mm long with bend of 45 degree with flange, complete all as specified and directed. |
| 43 | S&F PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed. |
| 44 | S&F of 32mm dia collapsible waste pipe not less than 800mm long for wash hand basin and sink, complete all as specified and directed. |
| 45 | S&F of 40mm dia collapsible waste pipe not less than 800mm long for wash hand basin and sink, complete all as specified and directed. |
| 46 | S&F in repair towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190gms), complete all as specified and directed. |
| 47 | S&F 5.5mm thick glass shelf of size 12cm wide x 60cm long for wash hand basin etc., complete all as specified and directed. |
| 48 | M&L 75mm diaPVC (SWR) floor trap, plain with grating including jointing with solven cement as in repairs, complete all as specified and directed. |
| 49 | S & F in repair 110mm bore PVC (SWR) rain water pipes,single sockets, in any length with sealant rubber ring joints fixed to wall with and including necessary MS flat iron clamps of size (40x4mm), complete all as specified and directed. |
| 50 | S&Fin repair of 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed. |
| 51 | S & F in repair 75mm bore PVC (SWR) rain water pipes, single sockets, in any length with sealant rubber ring joints fixed to wall with and including MS flat iron clamps (size 40 x 4mm), complete all as specified and directed. |
| 52 | S&Fin repair of 75mm bore, PVC (SWR) bends of any radius, complete all as specified and directed. |
| 53 | S&Fin repair 75mm bore PVC (SWR) junction, single, (single T) equal or unequal, complete all as specified and directed. |
| 54 | S&F in repair CP grating 100mm dia fixed with white cement, complete all as specified and directed. |
| 55 | S&Frotational moulded polyethylene water storage tanks, triple layered, (cylindrical vertical with closed top) ISI marked, confirming to IS 12701-1989, hoisted and fixed in position all as specified in SSR Part I (1000 ltr capacity) including 20mm Nipple suitable for HDPE water tank and ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe inculding dismantling of old unserviceable water tank, complete all as specified and directed. |
| 56 | S&F in repair 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe or brass, complete all as specified and directed. |
| 57 | Taking down chowkats with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each., complete all as specified and directed. |
| 58 | Taking down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed. |
| 59 | Taking down shutter of any description exc. 1 Sqm but n.exc 2 Sqm each, complete all as specified and directed. |
| 60 | S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 61 | Cutting holes in brick walls built in CM for inserting hold fasts and making good dismantled portion in CM (1:3) or PCC (1:2:4), type B-1 (using 12.5mm graded crused stone aggregate) as in depth of embedded portion of hold fast n. exc. half brick, complete all as specified and directed. |
| 62 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawings, complete all as specified and directed. |
| 63 | S&F factory made solid PVC moulded door shutter with wood board core free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed. |
| 64 | S&F 30mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and directed. |
| 65 | S&F 35mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc Sqm divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and directed. |
| 66 | S&F for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 67 | S&F butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-21, complete all as specified and directed. |
| 68 | S&F aluminium alloy anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheets, cast extruded sections and fixing bolt and sliding bolts of extracted sections, complete all as specified and directed. |
| 69 | S&F 150mm long aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed. |
| 70 | S&F 150mm long aluminium handle, cast type anodised, complete all as specified and directed. |
| 71 | S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor 150mm size of cover plate, complete all as specified and directed. |
| 72 | S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate including brass brackets, complete all as specified and directed. |
| 73 | M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm width or girth and applyingtwo coats of synthetic enamel paint (1st grade quality) over a coat of pink primer, complete all as specified and directed. |
| 74 | Hacking out old broken glass any thickness size quality or description from metel frame/aluminium frame including punching or drilling our old glazing pins/spring clips, complete all as specified and directed. |
| 75 | S&F 4mm thick sheet glass, ordinary quality,as in doors, window, showcase in aluminium frame work & similar work exc. 0.50 Sqm in each pane including neoprene gasket, complete all as specified and directed. |
| 76 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. |
| 77 | S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. |
| 78 | M&L for mild steel framed work such as grill, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barrel iron doors, ladders framed balusters, walks railings, frame work of water tanks and similar work conforming to E-165 (Fe-290), complete all as specified and directed. |
| 79 | M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed. |
| 80 | S&F for 605x 605mm GI frame work for seamless ceiling comprising of Gl perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and webof 45mm suspended from soffit at approx 900mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50mm and flange of26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and providing 6mm non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/aluminium framework with screws, 6 0x 60cm in size, fixed with nails to timber framework or with staples on snap grid including dismantling of old unserviceable ceilingboards of any description, including cover fillets, complete all as specified and directed. |
| 81 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed. |
| 82 | S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats Fe 410w (Gde E-250) complete all as specified and as directed. |
| 83 | Taking down carefully point wiring of any type, size and description from hard/ teak wood batten/through pipes/casing capping(light, fan, sockets and socket outlets etc) including removal of battens, pipes, plug sockets, socket outlets, switches, shades, ceiling roses, light fittings etc. complete and making good the disturbed surface to match with existing, complete all as specified and directed. |
| 84 | M & L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLSH type multi stranded copper conductor, single core drawn in and including PVC conduit, medium grade, (ISI marked), heavy duty of adequate sizeincluding its accessories not less than 20mm dia rigid PVC conduit \"medium grade ISI marked including all conduit accessories including pressed steel terminal box of required size factory made with top cover of ISI marked plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLSH type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site & including chases cutting& making good disturbed surface & applying finishes to match existing surface etc. for one light/fan point controlled by one, one way switch single pole, complete all as specified and directed. |
| 85 | All as per item No 84.00 here-in before but one 3 pin 5 Ampssocket outlet on same board controlled by other switch, complete all as specified and directed. |
| 86 | All as per item No 84.00 here-in before but one 3 pin 5 Amps socket outlet on the independent board controlled by other swtich, complete all as specified and directed. |
| 87 | All as per ser item No. 84.00 here in above but for one 16 Amp 6 pin switch socket outlet independent point including PVC cable 2.5 Sqmm FRLSH type copper stranded conductor along with 2.5 Sqmm continious PVC insulated unsheathed standard copper conductor cable FRLSH type for as earth wire, complete all as specified and directed. |
| 88 | S&F in repair switch piano flush button, single pole, one way, 6 Amps 240 volts, complete all as specified and directed. |
| 89 | S&F in repair switch and socket combination, flush type, 5 pin, 6A, complete all as specified and directed. |
| 90 | S&F in repair switch and socket combination, flush type,6 pin, 16A, complete all as specified and directed. |
| 91 | S&F in repair socket outlet,flush type, 5 pin, 6 Amp, complete all as specified and directed. |
| 92 | S&F in repair stepped type electronic fan regulator, modular type AC 230 volt suitable for any type of ceiling fan, complete all as specified and directed. |
| 93 | S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including taking down old ceiling fan, any type and deposited to AGE E/M store yard, completes all as specified and directed. |
| 94 | S&F exhaust fan, steel body AC, single phase, 230V of size 300mm sweep with, blades, and frame and louversincluding cutting wall for fixing exahaust fan of size 300mm sweep and making good the opening in CM (1:3) or PCC (1:2:4) type B1 as required at site including taking down old exhaust fan, any size and deposited to AGE E/M store yard, completes all as specified and directed. |
| 95 | S&F ceiling rose of size 65 x 50mm surface bakelite 240 Volts,three terminal, complete all as specified and directed. |
| 96 | S&F LED lights fitting 1x 20 W, 220V, AC, with driver, LED rodcompleteconnecting up with 2/3 core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed. |
| 97 | S&F power unit suitable 25 Amp including sockets25 Amps, and 02module box for mounting of power unit and power socket, complete as specified and directed. |
| 98 | S&F in repair modular socket 16 Amp, 2 module box for mounting of power unit and power socket, complete all as specified and directed. |
| 99 | S&F in repair metal flush box, 2 module, mounting of power unit and power socket, complete all as specified and directed. |
| 100 | S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V, AC, decorative type with driver, LED tube lightof 10watt connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, completes all as specified and directed. |
| 101 | S&F MCB DB, SPN, 12way IP 43 protection, double door, concealed on wall, completes all as specified and directed. |
| 102 | S&F RCBOs for earth leakage, over load and short - circuit protection 32Amp DP 100 mA, completes all as specified and directed. |
| 103 | S&F MCB DB, SPN, 8way IP 43 protection, double door, concealed on wall, completes all as specified and directed. |
| 104 | S&F MCB DB 6 to 32 Amps, 240V, 10 KA, \"C\" curve, including connection of testing, completes all as specified and directed. |
| 105 | S&F MCB SPN6 to 32 Amps, 10 KA, \"C\" curve, complete all as specified and as directed. |
| 106 | Supply and draw sub main wiring in repairs of two run 6.0 sqmm single core (FRLSH) PVC insulated, unsheathed multistranded copper conductor cable 1100 Volt grade, drawn through and including PVC conduit (ISI marked), medium duty, of not less than 25mm size including all conduit accessories, concealed to the surfaces of the wall/ceiling including one run of6.0 sqmm single core (FRLSH) PVC insulated unsheathed copper earth continuity including taking down existing sub-main wiring, complete all as specified and directed.Note: (i) Two runs of single core cable with one run of earth continuity conductor including PVC conduit & accessories shall be measured and paid as one length.(ii) Cutting chases shall be measured and paid separately. |
| 107 | Supply and draw sub main wiring in repairs of two run 4.0 sqmm single core (FRLSH) PVC insulated, unsheathed multistranded copper conductor cable 1100 Volt grade, drawn through and including PVC conduit (ISI marked), medium duty, of not less than 25mm size including all conduit accessories, concealed to the surfaces of the wall/ceiling including one run of4.0 sqmm single core (FRLSH) PVC insulated unsheathed copper earth continuity including taking down existing sub-main wiring, complete all as specified and directed.Note: (i) Two runs of single core cable with one run of earth continuity conductor including PVC conduit & accessories shall be measured and paid as one length.(ii) Cutting chases shall be measured and paid separately. |
| 108 | M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanisedmeans of earth wire 4mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 20mm bore and watering pipe GI medium grade of 20mm bore and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC (1:3:6) type C-2 all as shown in electrical plate No-3 of SSR part-I (2009) connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion, including demolition of old unserviceable earthing of any description, complete all as specified and directed.Notes : Proper earthing pit should be provided with pit cover. |
| 109 | S&F water heater stoarage type, capacity 50 litres (minimum 2 Kw heating element) BEE 5 star rated, 8 ber pressure rating, vartical hanging including proper hanging arrangement on wall, cold/hot water connection of required lenghth (not more than 3 mtr), hot water outlet line, complete all as specified and as directed. |
| 110 | S&F of wall mounted fan, capacity 90 CFM, 2050 RPM, 110 watt, size 400mm with all fixing arrangement on wall anf connecting cable upto ceiling rose, complete all as specified and as directed. |
| 111 | M & L 150mm bore CI Fittingfor bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \"Y\" junction, double branch, cross (flange sockets or socket and spigot) collars, caps and plugs, complete all as specified and directed. |
| 112 | M & L for run lead joints in position for cast iron spigot and socket ends for pipes of size 150mm bore, complete all as specified and directed. |
| 113 | Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation of pole/stay, or cable trenches etc and getting out in soft/loose soil, complete all as specified and directed. |
| 114 | Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed. |
| 115 | Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed. |
| 116 | M & L for construction of valves pit chamber of size (900mm x 900mm x 900mm, internal), 15cm thick PCC foundation using PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate), 25cm thick brick wall, using old size burnt clay brick in CM (1:4), 10mm thick rendering on internal and extranal surfaces both in CM (1:4), PCC (1:2:4) type B1 coping (using 20mm graded crushed stone aggregate) for grouting MS frame including foundation 3mm thick MS top sheet cover with locking arrangement including 50mm pad lock with double key arrangement, MS frame work made out of 40 x 40 x 5mm thick angle iron including painting of steel surface with two coats of synthetic enamel paint over a coat of red oxide primer incuding necessary excavation in any type of soil, returning, filling in and removal of surplus soil to a distance not exceeding 50 mtrs including demolition of existing cracked valve chamber, complete all as specified and directed. |
| 117 | Cutting of bituminous road/hardstanding/path/plinth protection etc for laying of pipe line, getting out and disposal of materials to a distance n. exc. 50m from the site of work, complete all as specified and directed. |
| 118 | M & L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) for foundation, filling, mass concrete, making good to disturbed surfaces of road/hardstanding/plinth protection etc, complete all as specified and directed. |
| 119 | M&L for cutting CI/DI/GI pipes and reducing to required length for connection of Tee or branches of 50/80mm bore pipe, in position, complete all as specified anddirected. |
| 120 | Note: An amount of Rs.51,368.00 on account of Credit Schedule for schedule \"A\" part - II shall be deducted from the total amount of BOQ to arrive at the contract sum. |
| 121 | Supply and fixing energy efficient ‘LED Flood Light120 W LED luminairewith Aluminium dia cast housing, toughened glass cover with IP 66 protection, CCT 5700 K including fixing arrangment on wall/pole / surface and connecting cable up to nearest ceilign rose into flexible PVC conduit. Make : Crompton/Havells/ Surya/Philips |
