|
| 1 | Dismantling of precast concrete block masonry built in cement mortar including all quoins, arches, pillars, etc, complete all as specified and as directed. |
| 2 | Demolition of un-reinforced cement concrete in ground floor and pavings not exc 15 cm thick (below or above ground level) and removing all the rubbish as directedcomplete all as specified and directed |
| 3 | Demolition of reinforced cement concrete in chajjas and similar suspended work (cut as required to facilitate demolition) and removing all the rubbish as directedcomplete all as specified and directed |
| 4 | Taking down chowkats or frames not exc 1.5 sqm each (without taking of shutters from the frame) complete all as specified and as directed. |
| 5 | Taking down chowkats or frames exc 1.5 sqm but not exc 4 Sqm each (without taking of shutters from the frame) complete all as specified and as directed. |
| 6 | Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm complete all as specified and as directed. |
| 7 | Excavation in trenches not exc. 1.50m wide and not exc 1.5 m in depth; for foundation etc.; or for shafts, wells, cesspits, manholes, pier holes not exc 10 sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.. |
| 8 | M&Lfor PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) asin foundations filling and mass concrete complete all as specified and as directed. |
| 9 | M&L for pre-cast cement concrete block masonry with solid blocks type C1, PCC 1:3:6 (using 20mm graded crushed stone aggregates), exc 10cm in width and setting in CM 1:6 complete all as specified and as directed. |
| 10 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed. |
| 11 | Removing surplus excavated soil and debries obtained from demolition to a distance exceeding 250m but n exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed. |
| 12 | M&L for 15 mm thick cement plaster on fair face of brick work or concrete surface in CM 1:4 for wall finished even & fair complete all as specified and as directed. |
| 13 | M&L for applying twocoats ofacrylic emulsion paintof Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on new plastered surfacesofwalls complete all as specified and as directed. |
| 14 | M&L for rendering 15 mm thick on stone masonary surfaces or surface other than fair face of brick work or on one side of lathing for wall in CM 1:6 to be finished even & smooth without using extra cement complete all as specified and as directed. |
| 15 | M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper on walls over a coat of alkali-resistant priming paints over 3mm thick wall care putty complete all as specified and as directed. |
| 16 | M&L forbroken stone or boulder hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 17 | M&L for 150mm thick PCC1:4:8, type D2 (using 40mm graded cushed stone aggregates) as in sub base of flooring complete all as specified and as directed. |
| 18 | M&L for 25mm thick plain cement concrete 1:2:4,type B1 (using20mm graded cushed stone aggregates) as in floor complete all as specified and as directed. |
| 19 | M&L for plain cement concrete, 75mm thick, (1:3:6), type C-1 (using 20mm nominal size crushed and graded stone aggregates)for plinth protection including filling of expansion joint with bituminous mixture finished fair and evencomplete all as specified and as directed. |
| 20 | M&L fornon skid ceramic tiles, coloured,7 to 8mm thick (square or rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm, set and jointedin neat cement slurry and pointed in white cementwith pigment to match, as in floors laid over and including 15mm thick screed bed in cement mortar 1:6complete all as specified anddirected. |
| 21 | M&L for glazed ceramic coloured tiles in verticle surfaces such as skirting, dado, etc., of size450mmX300mmX7mm thick set and jointedin neat cement slurry and pointed in white or coloured cementto match shaded of tiles laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed. |
| 22 | M&L forsingle piece white colour vitreous china floor mounted pedestal pattern wash down water closet with seat cover having PVC/CI\"P\" or \"S\" type trap element, rimless one pieceincluding all accessoreis complete all as specified and as directed.Make Cera , Cat Part No. S1013217 or equivalent make as specified in list of makes of Particular Specifications |
| 23 | M&L forHealth faucet ABS body with 1mtr SS braided PVC hose pipe complete all as specified and as directed... Make Cera, Cat Part No. F8030111ABor equivalent make as specified in list of makes of Particular Specifications |
| 24 | S&F toilet paper holder with flap guard complete all as specified and directed. Make: Cera, Cat Part No. F5003110or equivalent make as specified in list of makes of Particular Specifications |
| 25 | S&Ftowel rail 600mm long with fittings complete all as specified and directed. Make: Cera, Cat Part No. F5015103CHor equivalent make as specified in list of makes of Particular Specifications |
| 26 | S&F two way bib cock with wall flange and aerator complete all as specified and directed.. Make: Cera, Cat Part No. F1001163or equivalent make as specified in list of makes of Particular Specifications |
| 27 | S&F bib cock with wall flange and aerator complete all as specified and directed. Make: Cera, Cat Part No. F1001151or equivalent make as specified in list of makes of Particular Specifications |
| 28 | S&Fover head shower of size 100mm x 100mm, with 200mm long shower arm and wall flange completeallas specified and directed. Make: Cera, Cat Part No. F7020110SSor equivalent make as specified in list of makes of Particular Specifications |
| 29 | S&F vitreous China wash hand basin, white in colour,(counter type oval shaped) of size 560mmX470mmX190mm including bottle trap 150mm with cutting of Granite topcomplete all as specified and directed. Make Cera, Cat Part No. S2030104 & F8060101or equivalent make as specified in list of makes of Particular Specifications |
| 30 | S&F5.5mm thick bevelled edge mirror of selected quality glass, mounted on 12mm thick PVC board fixed to PVC sleeves with chromium plated brass screws and cup washers over screw head complete all as specified and directed |
| 31 | S&F pillar tapsuitable for 15mm dia pipe complete all as specified and directed. Make Cera, Cat Part No. F1001101 or equivalent make as specified in list of makes of Particular Specifications |
| 32 | S&Fangle cock with wall flange complete all as specified and directed. Make Cera, Cat Part No. F1001201 or equivalent make as specified in list of makes of Particular Specifications |
| 33 | S&F stop cock concealed type with wlll flange suitable for 15mm dia pipe complete all as specified and directed. Make Cera, Cat Part No. F1001351& F4050102 or equivalent make as specified in list of makes of Particular Specifications |
| 34 | S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed |
| 35 | S&Fsink cock wall mounted with with long swivel spout and wall flange complete all as specified and directed. Make Cera, Cat Part No. F1001251 or equivalent make as specified in list of makes of Particular Specifications |
| 36 | S&F wall mounted Sheet glass shelf assembly (corner self) consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed |
| 37 | S&F stainless steel Kitchen Sink, made of 1mm thick stainless steel sheet, with plugs and washers, including cutting of granite top and fixing complete in all respect, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed |
| 38 | M&L for machine cut cudappah stone slab (polished) 40-50mm thick fixed to wall including cutting grooves and cutting hole for WHB complete all as specified and directed |
| 39 | M&L for 20mm thick granite (of any type) work, (table rubbed and polished) in platform (for counter type Sink/WHB) and like in cement mortar (1:4) or pasting over cudappah stone slab including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 40 | M&L for providing moulding to granite stone of counters vanities etc including machine polishing to edge to give high gloss finish etc complete all as specified and directed |
| 41 | S&F PVC SWR pipe110 mm bore, single socketed in any length with rubber ring joints,fixed to walls including clamps and/or cutting concrete portion and making good as required complete all as specified and directed |
| 42 | S&F PVC SWR pipe75 mm bore, single socketed in any length with rubber ring joints,fixed to walls including clamps and/or cutting concrete portion and making good as required complete all as specified and directed |
| 43 | S&F PVC pipe50 mm bore of pressure rating 6kg/sq cm fixed to walls, ceiling or in floors including all fittings and clamps and/or cutting concrete portion and making good as required complete all as specified and directed |
| 44 | S&F 110 mmbore PVC (SWR) junction single, (single T) equal or unequal with access door complete all as specified and directed |
| 45 | S&F 75mmbore PVC (SWR) junction single, (single T) equal or unequal with access door complete all as specified and directed |
| 46 | S&F 110 mmbore PVC (SWR) bend of any radius complete all as specified and directed |
| 47 | S&F75 mmbore PVC (SWR) bend of any radius complete all as specified and directed |
| 48 | S&F75 mmbore PVC (SWR) bend with oval access door of any radius complete all as specified and directed |
| 49 | S&F 75mm bore PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement complete all as specified and directed |
| 50 | S&F75 mm dia PVC vent cowl complete all as specified and directed |
| 51 | S&FUnplasticised PVC pipes 25mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe including all fitting such as bends,elbows, tees tank connector and fixing to existing pipe complete all as specified and directed |
| 52 | S&FUnplasticised PVC pipes 15mm dia of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe including all fitting such as bends,elbows, tees tank connector complete all as specified and directed Note : The quoted rate are inclusive of conceal of pipes with cutting chases in walls / concrete) |
| 53 | S&Fin repairs25 mm bore Gun metal gate valves, with iron wheel head, screwed both ends for iron pipe and fixed etc complete all as specified and directed |
| 54 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directedNote: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 55 | M&L for factory made single extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directedNote: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 56 | M&L forfactory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter (single/double) of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicityindex of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 57 | M&L forfactory made wire mesh solid WPC (Wood Polymer Composite) door shutter (single/double) consisting of density of 500 kg/cum, door to be with SS mosquito wire mesh and XTN aluminium mesh for additional strength and safety pourpose. the door should be water proof, termite proof, fire retardant, and having screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. fixing with butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: butt hinges and other fittings shall be paid separately) |
| 58 | S&F 100 mm long butt hinges stainless steel to door frame with necessary screwing or bolting complete all as specified and directed |
| 59 | S&F 150 mm long aluminium anodised handle fabricated type complete all as specified and directed. |
| 60 | S&F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed. |
| 61 | S&F300 mm Aluminium alloy, anodised sliding door bolt with hasp and stapple bolt type complete all as specified and directed. |
| 62 | S&Fdoor closer hydraulically regulated, cast iron body,designation No 2 universal type suitable for door shutter of 701 to 850mm in width and weight between 36 to 60 Kg including necessary fixing with shutter and door frame complete all as specified and directed |
| 63 | S&Frolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle, channel, or flat section) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) quality - Acomplete all as specified and directed |
| 64 | S&Fpre painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed |
| 65 | M&Lformild steel work for wind ties for roof including securing bolts including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 etc., complete all as specified and directed. |
| 66 | M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed. |
| 67 | M&L for preparation of new steel surfaces of any description, not exc 10cm in width or girth, when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed. |
| 68 | M&Lfor providing and fixing 12mm thick Gypsum board in ceiling as per manufacturer instruction over and including powder coated aluminium snap grid frame work (size of grid 605 x 605mm) supported by hangers 2 to 4 mm dia GI (up to 1200mm length /as per site requirement) adjusting level fixed to roof slab/walls/wooden/steel members by means of ceiling cleats and painting two coats of oil bound distemper over a coat of primer and preparatory work complete all as specified and directed |
| 69 | S&F Anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified and directed |
| 70 | S&F Anodised aluminium powder coated door shutters, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium powder coated snap beading, screws, handle 2 Nos in each door, hinges complete all as specified and directed |
| 71 | S&F Anodised aluminium powder coated windows and ventilators shutters, side/top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium powder coated snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 nos), suitable handle (1 No) complete all as specified and directed |
| 72 | S&F Anodised aluminium grills powder coated of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass / stainless steel screws @200 centre to centre, including cutting the grills to proper opening size for fixing and operation of handles and fixing fixing approved anodised aluminium standard section around the opening complete all as specified and directed |
| 73 | S&F figured glass, pin head type 4 mm thick, not exceeding 0.5 Square Metre for each pane, glazing with oil putty or aluminium beading complete all as specified and directed |
| 74 | S&F sheet plain glass5 mm thick, ordinary quality, in squaresnot exceeding 0.5 Square Metre for each pane, glazing with oil putty or aluminium beading complete all as specified and directed |
| 75 | S&Fstainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws or aluminium beading complete all as specified and directed |
| 76 | S&FDouble action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixedcomplete all as specified and directed |
| 77 | S&F brass mortice lock, vertical type, size 100mm, 4 leverscomplete all as specified and directed |
| 78 | M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper on walls over a coat of alkali-resistant priming paints over 1mm thick wall care putty complete all as specified |
| 79 | M&L for one coats of oil bound distenper on old decorated surfaces of ceilings including necessary preparation of surfaces complete all as specified and directed |
| 80 | M&L for one coats of synthetic enamel paint on old wooden surfaces of any description over 10cm width or girth including necessary preparation of surface complete all as specified and directed |
| 81 | M&L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surface complete all as specified and directed |
| 82 | S&Fin repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws or aluminium beading complete all as specified and directed |
| 83 | Supply and fix in repairs sheet plain glass4 mm thick, ordinary quality, in squaresnot exceeding 0.5 Square Metre for each pane, glazing with oil putty or beading including hacking out old broken glass (any thickness, size, quality and description) complete all as specified and directed |
| 84 | M&L for 12mm thick prelaminated particle board, interior grade, prelaminated both sides fixed with screws to frame work as in ceiling and wall panelling complete all as specified and as directed, |
| 85 | Taking down cement plaster on brick/concrete/stone masonry walls etc incl racking out joints, hacking for key, scrubbing down with water etc complete including removing rubbish off the premises complete all as specified and directed. |
| 86 | M&L for cutting holes of superficial area not exceeding 150 Sq cminto or through in brick walls built in cement mortar or cement lime mortar and stone walls built in cement mortar or PCC solid block walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and directed. |
| 87 | M&L for cutting existing steel tubing for altration or additions including screwing/connecting existing water tubing (25 mm or 32 mm) for alterations or additions (or lengthening screw on pipe to form connector) in position complete all as specified and directed. |
| 88 | M&L for cutting out concrete blocks, slabs, brick work or stone masonry (in alternate course), forming toothing for and bonding new work of pre-cast cement concrete solid block masonry type C1, PCC 1:3:6, using 20mm graded stone aggregate in CM 1:6 into old work complete all as specified and as directed. |
| 89 | S&F decorative stainless steel curtain rod 25 mm dia, 1.25mm wall thickness complete all as specified and directed. |
| 90 | S&F stainless steel brackets for fixing of 25mm dia curtain rod to wall and including decorative stops/ rollers/end cap fixed to both ends of 25mm dia stainless steel rod, all as specifiedNote: Each pair inclusive of two numbers of stainless steel brackets and two numbers of decorative stainless steel stops/roller/end cap complete all as specified and directed.. |
| 91 | M&L for machine cut kota stone slab flooring 20mm to 22mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beeswax polish over and including 20mm screed bed in cement mortar 1:4 complete all as specified and directed. |
| 92 | M&L for cutting chases, pinning in not exc 10 cm girth in pcc block walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of roof sheet, landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, complete all as specified and directed. |
| 93 | M&L for plain cement concrete(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) as incopings,and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed |
| 94 | S&F17mm to 18mm thick WPC sheet of one side prelam/rigidlam and other side plain colour fixed with screws, solvent cement/adhesive to make cup board/ cabinet with frame & shutters/drawer front/sides, partitions, shelves providing etc. including 1mm thick PVC lipping/beading fixed with solvent over edges of ply of required width and colour complete all as specified and directed. |
| 95 | S&F sleek soft hydraulic auto closing 3D (Big bend/middle bend/straight arm type) stainless steel finish hinges openable of 0 or 15 degree crank for cup board/ cabinet shutters (sample available in GE Office) complete all as specified and directed. Make: Hettich, Harrison, Earl Bihari |
| 96 | S&F stainless steel handles 100mm size, D type dotted for cup board, cabinet shutters complete all as specified and directed. |
| 97 | Dismantling floor hearth/ wall tiling including cement mortar bedding (but not backing) and removing tiles & rubbish off thepremisescomplete all as specified and directed. |
| 98 | M&L for vitrified ceramic coloured tiles (double charged), 8 to 10mm thick (square or rectangular), polished, area of each tile not exc 0.36 sqm, set and jointedin neat cement slurry and pointed in white or coloured cementto match, as in floors over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 99 | M&L for vitrified ceramic coloured tiles (double charged), 8 to 10mm thick (square or rectangular), polished, area of each tile not exc 0.36 sqm, set and jointedin neat cement slurry and pointed in white or coloured cementto matchshade of tileson vertical surfaces as in skirting, dado laidover and including 10mm thick backing coat in cement mortar 1:3 complete all as specified and directed. |
| 100 | M&L for dismantling of boarding of old built in cup boards fixed in any position with nails complete all as specified and as directed. |
| 101 | Taking & Refixing of shutters of any description (MS/woodenshutter gauzed & glazed) in same opening not exc 1 Sqm, including taking down, easing, welding and adjusting and also refixing old builders hardware as required including renewal of unserviceable screws and new builder\"s hardware like handle, stays hinges of any type as per site requirement etc complete all as specified and directed. |
| 102 | M&L for pre-cast cement concrete block masonry with solid blocks,in PCC 1:3:6,Type C1 (using 20mm graded crushed stone aggregates), exc 10cm in width and setting in CM 1:4 complete all as specified and directed |
| 103 | M&L for re-inforced concrete pipe of 150mm dia of class NP-2 laid and jointed complete with collars complete all as specified and directed |
| 104 | M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of 150mm bore after they are laid and tested complete all as specified and as directed. |
| 105 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and as directed. |
| 106 | M&L for pre cast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slab set in cement mortar 1:4 complete all as specified and as directed.. Note:- Reinforcement shall be measured and paid separately. |
| 107 | M&L for TMT bars 6mm dia to 8mm dia cut to length, bent to shape required,including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. |
| 108 | M&L for round bars 12mm for handles dia cut to length, bent to shape required,including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. |
| 109 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. |
| 110 | Supply only integral water proofing compound complete all as specified and as directed. |
| 111 | M&L for cutting exising manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required. complete all as specified and as directed. |
| 112 | M&L for construction of conventional LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connectioncomplete for 20 Users complete all as specified and as directed.. |
| 113 | M&L for construction of Soakage well of size 3.0 M dia and 3.0M effective depth, excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen camber made of brick masonry in CM (1:4), RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats complete all as specified,as directed and shown on Drgs. |
| 114 | M&L for plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregates) as in concrete bed to drain pipes of 300mm bore including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and as directed. |
| 115 | M&L for re-inforced concrete pipe of 300mm dia of class NP-2 laid and jointed complete with collars complete all as specified and as directed. |
| 116 | M&L for point wiring forone light/exhaust fan/fan pointcontrolled by one switch with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded FRLS copper conductor cable confirming to IS drawn through and including non metallic PVC conduit concealed/semi concealed including Flush type metal GI boxes for fixing modulartypeswitches, sockets, regulators etc. including provision of multistranded 1.5 Sqmm FRLS copper conductor as earth wire connected to common earth dolly and earth in distribution board including cutting of stone masonary/ wall complete all asspecified and directed . |
| 117 | All as perSl item No 116 here in with but for one 5 Amps socket independent including 1.5 Sqmm earth continuty FRLS Copper conductor-ditto- |
| 118 | All as per Srl item No. 116 here in with but with 2.5 SqmmFRLS copper cable for one 15 Amps power point.Including 2.5 Sqmm FRLS copper conductorfor earth continuity conductor and connecting it to earth -ditto- |
| 119 | S&Fswitch modulartype single pole 6 Amps one wayAC 230V, 50HZ complete all asspecified and directed |
| 120 | S&F celing rose surface backlite 63 mm dia two to three terminals complete all asspecified and directed |
| 121 | S&Fmodulartype socket5AAC 230V, 50HZ complete all asspecified and directed |
| 122 | S&Fmodulartype switch/Socket combine 6A/16A multi purpose AC 230CV, 50HZ complete all asspecified and directed |
| 123 | S&Fmodularwhite cover plate with frame 2 module complete all asspecified and directed |
| 124 | S&F modularwhite cover plate with frame 3 modulecomplete all asspecified and directed |
| 125 | S&F modularwhite cover plate with frame 6 module complete all asspecified and directed |
| 126 | S&F modularwhite cover plate with frame 8 module complete all asspecified and directed |
| 127 | M&Lfor sub main wiring with 2runs of 4.0 Sqmm PVC insulated FRLS Copper conductor cable including PVC conduit of Suitable along with one run of 4.0 Sqmm FRLS copper cable for earth continuity conductor as earth lead for sub main wiring and connecting to common earth dolly complete all asspecified and directed |
| 128 | S&FLED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all asspecified and directed |
| 129 | S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all asspecified and directed |
| 130 | S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all asspecified and directed |
| 131 | S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all asspecified and directed |
| 132 | S&F SPN DB 4 Way with 200 amps rated bus bar double door complete all asspecified and directed |
| 133 | S&F 240V, 10KA \"C\" curve miniature circuit breaker (MCB) SPN and current carrying capacity 32 Amps in the MCB DB complete all asspecified and directed |
| 134 | S&F 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB complete all asspecified and directed |
| 135 | M&Lfor earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to GI earth lead wire4 mm dia by means of bolts, nuts,check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dia and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) including testing complete all asspecified and directed |
