Supply Of Footwear For Welders To Is: 15298 ( Pt.2 ) 2011 With Amnd. No.1 Of June-2012. Classification Of Footwear As Per Clause 4, Table 1, Code Designation 1 & Design B Ankle Shoe As Per Figure -3 Of Design Of Footwear ( Without Lace ) . Basic Requirement For Safety Footwear As Per Clause 5, Classification- I Of Table -2 . ( A ) With Full Insocks As Per Table -3 , ( B ) Water Permeable Insole Asper Table -3, ( C ) Additional Requirements & Parameters Shall Comply With The Standard Governing Specification. For Special Application Standard Marking Of Bis & Bis Compliance Certificate Must Be Approved And Submitted By The Manufactuter.Note: Welders Safety Shoe Shall Be Provided With Protective Flap Cover With Velcrow Fastener For Quick Entry And Release Of The Foot, On Outer Facing Without Lace Shoe Provided With Elastic Gusset Joining Two Quarter Under Inner Leater Tongue On Inside For Foot Clamping . Size, 6 No.-15, 7 No.-38, 8 No .-84, 9 No.- 56, 10 No.-25, 11 No.- 02 Pairs, However If Any Change In Size It Will Be Conveyed To The Supplier. As Per Drg.No. - Specn: Is: 15298 ( Pt.2 ) 2011 With Amnd. No.1 Of June- 2012.Footwear For Welders To Is: 15298 ( Pt.2 ) 2011 With Amnd. No.1 Of June-2012. Classification Of Footwear As Per Clause 4, Table 1, Code Designation 1 & Design B Ankle Shoe As Per Figure -3 Of Design Of Footwear ( Without Lace ) . Basic Requirement For Safety Footwear As Per Clause 5, Classification- I Of Table -2 . ( A ) With Full Insocks As Per Table -3 , ( B ) Water Permeable Insole Asper Table -3, ( C ) Additional Requirements & Parameters Shall Comply With The Standard Governing Specification. For Special Application Standard Marking Of Bis & Bis Compliance Certificate Must Be Approved And Submitted By The Manufactuter.Note: Welders Safety Shoe Shall Be Provided With Protective Flap Cover With Velcrow Fastener For Quick Entry And Release Of The Foot, On Outer Facing Without Lace Shoe Provided With Elastic Gusset Joining Two Quarter Under Inner Leater Tongue On Inside For Foot Clamping . Size, 6 No.-15, 7 No.-38, 8 No .-84, 9 No.- 56, 10 No.-25, 11 No.- 02 Pairs, However If Any Change In Size It Will Be Conveyed To The Supplier. As Per Drg.No. - Specn: Is: 15298 ( Pt.2 ) 2011 With Amnd. No.1 Of June- 2012., Footwear For Welders To Is: 15298 ( Pt.2 ) 2011 With Amnd. No.1 Of June-2012. Classification Of Footwear As Per Clause 4, Table 1, Code Designation 1 & Design B Ankle Shoe As Per Figure -3 Of Design Of Footwear ( Without Lace ) . Basic Requirement For Safety Footwear As Per Clause 5, Classification- I Of Table -2 . ( A ) With Full Insocks As Per Table -3 , ( B ) Water Permeable Insole Asper Table -3, ( C ) Additional Requirements & Parameters Shall Comply With The Standard Governing Specification. For Special Application Standard Marking Of Bis & Bis Compliance Certificate Must Be Approved And Submitted By The Manufactuter.Note: Welders Safety Shoe Shall Be Provided With Protective Flap Cover With Velcrow Fastener For Quick Entry And Release Of The Foot, On Outer Facing Without Lace Shoe Provided With Elastic Gusset Joining Two Quarter Under Inner Leater Tongue On Inside For Foot Clamping . Size, 6 No.-15, 7 No.-38, 8 No .-84, 9 No.- 56, 10 No.-25, 11 No.- 02 Pairs, However If Any Change In Size It Will Be Conveyed To The Supplier. As Per Drg.No. - Specn: Is: 15298 ( Pt.2 ) 2011 With Amnd. No.1 Of June- 2012.
