Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 30-11-2020 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 07-12-2020 |
| Name of Work: PROVN OF UGLB AT VEERBHADRESHWAR, WORK SERVICES FOR ITON PROJECT IMPLEMENTATION AT SALYARCHATTA AND CONVENTIONAL EARTHING PIT AT SHASHITHAR UNDER GE AIR FORCE JAMMU. (JOB NO 41 WEU/CAP-08/18-19, 23W/CAP/OTM-06/20-21 AND 23W/MW-08/20-21) | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Excavating over areas, n.exc 1.5 m deep and getting out in hard/dense Soil complete all as specified and as directed by Engineer-in-charge. | 110 | Cubic Metre | |
| 2 | 2 | Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil, complete all as specified and as directed by Engineer-in-charge. | 107.55 | Cubic metre | |
| 3 | 3 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed by Engineer-in-charge. | 52.9 | Cubic metre | |
| 4 | 4 | Broken stone hardcore of gauge exceeding 63mm but not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed by Engineer-in-charge | 2.5 | Cubic metre | |
| 5 | 5 | 100 mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base of floors and the like including finishing the surface rough complete all as specified and as directed by Engineer-in-charge. | 16 | Square Metre | |
| 6 | 6 | 100 mm thick plain cement concrete 1:2:4 type B-2 using 40mm graded crushed stone aggregates as in sub base of floors and the like including finishing the surface even and smooth including necessary form work if required complete all as specified and as directed by Engineer-in-charge. | 16 | Square Metre | |
| 7 | 7 | Walling of random rubble stone masonry uncoursed, with best quality locally available harder stones such as granite, trap, basalt, trap, basalt stone etc, well bonded, bedded and solidly hearted , built in cement mortar 1:6 complete all as specified and as directed. \nNote : The quantity of PCC bond stones paid under seperate item shall be deducted from the total volume of the stone masonary. | 25 | Cubic metre | |
| 8 | 8 | Pre-cast plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in bond stones and the similar works, set in cement mortar 1:6, including necessary form works, complete all as specified and directed by Engineer-in-charge. | 2 | CUBIC METRE | |
| 9 | 9 | Framed work as in windows with sliding shutter having 6mm thick MS sheeting complete, drilled for fixing of steel sheeting (including steel sheeting not less than 6mm thick) or other covering. Windows, etc. to be prepared for sliding with and including either hooks and hinges or steel hanging windows fittings (including of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and as directed by Engineer-in-Charge. | 260 | Kilogram | |
| 10 | 10 | Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting (including steel sheeting not less than 6mm thick) or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and as directed by Engineer-in-Charge. | 210 | Kilogram | |
| 11 | 11 | Providing, cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks for hold fasts, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed by Engineer-in-Charge. | 1 | Cubic Metre | |
| 12 | 12 | Rendering 20 mm thick on other than fair faces of brick work or stone masonry surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:6, complete all as specified and directed by Engr-in-charge. | 50 | Square\nMetre | |
| 13 | 13 | Rendering 20 mm thick on other than fair faces of brick work or stone masonry surfaces finished even and smooth (without using extra cement) on walls in cement mortar 1:6, mixed with liquid water proofing admixture all as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.\nNOTE: Water proofing admixture shall be measured and paid seperately under relevant item of this BOQ | 25 | Square\nMetre | |
| 14 | 14 | Preparation of new or previously untreated plastered surfaces of walls, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.\nMAKE: NEROLAC PAINTS / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS | 25 | Square Metre | |
| 15 | 15 | M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distempering over and including a coat of chalk whiteningm thick layer of cement based white wall care putty, complete all as specified and directed by Engineer-in-Charge.\nMAKE OF OBD: NEROLAC PAINTS / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS | 260 | Square\nMetre | |
| 16 | 16 | Preparation of new or previously untreated steel or steel based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.\nMAKE: NEROLAC PAINTS / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS | 20 | Square Metre | |
| 17 | 17 | Supply only Liquid Water Proofing admixture complete all as specified and directed by Engineer-in-Charge.\nMAKE: M/S JK CEMENT / M/S ACC LTD / M/S PIDILITE INDIA LTD RAIGARH / M/S FOSROC CHEMICAL INDIA LTD / \n | 10 | Litre | |
| 18 | 18 | Material and labour for applying a coat of bituminous primer conforming to IS-3384 @ 0.30 litre/Sqm on the prepared plastered surface, after drying of primer, applying a coat of hot blown VG-20 paving grade (60-80 penetration) bitumen conforming to IS-702 @ 1.20 kg/Sqm of plastered surfaces complete all as specified and as directed by Engineer-in-charge. | 16 | Square meter | |
| 19 | 19 | M&L for APP based polymeric membrane minimum weighing 3.6 Kgs/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gsm/sqm) laid on primed surface by forced application complete all as specified. APP membrane shall be laid by torching with 150 mm overlap and 75mm side lap as directed. Polymeric water proofing membrane should be five layered with centre core as 90 microns high density polythene film.\nThe products of the following firms shall be used for water proofing membrane: -\nMAKE: (a) \"Hyper Plus Standard\" (b) \"Multi Plus\" (c) Bengal Acquaflux-Bengal Bitumen\" (d) \"Superior Poly Plus S-30\" | 16 | Square meter | |
| 20 | 20 | Material and labour for PCC 1:2L4 type B-0 (using 12.5 mm graded crushed stone aggregates) of uniform thickness of 50mm in two layers of 25mm thick each with supply and laying of chicken wire mesh, 0.91 mm dia and 12 x 12mm aperture, laid in between two layers of PCC. Top surface of PCC padding shall be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. | 20 | Square metre | |
| 21 | 21 | TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.\nMake and Procurement: All as specified in PS clause No 8 of tender documents | 1160 | Kilogram | |
| 22 | 22 | TMT mild steel bars, 5mm dia and over upto and including 10mm dia, as in stirrups, spacers & binders, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.\nMake and Procurement: All as specified in PS clause No 8 of tender documents | 60 | Kilogram | |
| 23 | 23 | Reinforced cement concrete 1:1.5:3 (Nominal mix), (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engineer-in-charge. | 13.15 | Cubic metre | |
| 24 | 24 | Supply and filling sand filling in sand bags and placing in positions where directed complete all as specified and as directed. | 500 | Each bag | |
| 25 | 25 | Use and waste of form work to sides and sofits of floor or roof beams, beams haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc to obtain rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-charge. | 56.8 | Square metre | |
| 26 | 26 | Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-charge. | 47.1 | Square metre | |
| 27 | 27 | Excavation in trenches in hard/dense soil n.exc 1.5m wide and n.exc 1.5m depth in foundations etc for laying of pipe line, cable, manholes, sewage line and getting out complete all as specifed and as directed by Engineer-in-Charge. | 45.65 | Cubic Metre | |
| 28 | 28 | Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-charge. | 1.3 | Cubic Metre | |
| 29 | 29 | Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge. | 12.65 | Cubic Metre | |
| 30 | 30 | Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough flat finished surfaces complete all as specified and as directed. | 7.2 | Square metre | |
| 31 | 31 | Use and waste of form work to to sides of pillars, posts, struts, piers, columns and stanchions etc to obtain rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-charge. | 7.7 | Square metre | |
| 32 | 32 | Reinforced cement concrete 1:1.5:3 (Nominal Mix), (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engineer-in-charge. | 5.6 | Cubic metre | |
| 33 | 33 | Reinforced cement concrete 1:1.5:3 (Nominal Mix), (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-charge. | 3 | Cubic metre | |
| 34 | 34 | Reinforced cement concrete 1:1.5:3 (Nominal Mix), (using 20 mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-charge. | 1.65 | Cubic metre | |
| 35 | 35 | TMT mild steel bars, 6 to 8mm dia, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.\nMake and Procurement: All as specified in PS clause No 8 of tender documents | 260 | Kilogram | |
| 36 | 36 | Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including supply and fixing of necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including bottom of each chowkat to be welded with and including 25 x 3 mm thick flat iron projecting 10 cm on either side and back filling to chowkats with PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregates after applying and including one coat of black paint to prevent from corrosion complete all as specified and as directed by Engr-in-Charge.\nMAKE: M/S AGEW STEEL MANUFACTURE PVT LTD AHMEDABAD / M/S SHIV MULARA NARODA AHMEDABAD / GODREJ AND BOYCE MFG MUMBAI / SEN HARVIC MUMBAI / SHIVAM STEEL JAMMU\n | 5 | Running metre | |
| 37 | 37 | 35 mm thick, factory made, 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engr in Charge.\nMAKE: M/S WOOD PRODUCT INDORE / M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI / M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT / M/S PIONEER TIMBER PRODUCT CHANDIGARH / M/S SHIVA JOINERY & FURNITURE INDUSTRIES JAMMU. | 1.8 | Square metre | |
| 38 | 38 | Steel window (box type) factory made with side hung shutters including pintol hinges, with 02 Nos tower bolts of 150 mm size on each shutter, steel handle and stopper of Z section with sash bars dovetailed or welded ready for glass fixing, including all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer, without guard bars/grills complete all as specified and shown in drawing No CEPZ/TD-325/07 dated 04.02.2007 and CEPZ-TD-324/07 dated 04.12.07\nMAKE: M/S AGEW STEEL MANUFACTURE PVT LTD AHMEDABAD/M/S SHIV MULARA NARODA AHMEDABAD / GODREJ AND BOYCE MFG MUMBAI/SEN HARVIC MUMBAI / SHIVAM STEEL JAMMU | 5.4 | Square metre | |
| 39 | 39 | Factory made steel ventiletors conforming to IS-1038 with top hung shutters including hinges with 02 Nos mild steel tower bolts of 150 mm long, steel handle and stopper of Z section with sash bars dovetailed or welded for securing glass including guard bars/grills complete all as specified and directed by Engineer-in-Charge. (Note: - Glass panes shall be measured and paid for separately).\nMAKE: M/S AGEW STEEL MANUFACTURE PVT LTD AHMEDABAD/M/S SHIV MULARA NARODA AHMEDABAD / GODREJ AND BOYCE MFG MUMBAI / SEN HARVIC MUMBAI / SHIVAM STEEL JAMMU | 0.54 | Square metre | |
| 40 | 40 | Plain Sheet glass 3.00 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane up to forth storey bldg, complete all as specified and as directed.\n | 4 | Square Metre | |
| 41 | 41 | Mild steel sliding door bolts, 300mm long, plate type, stove enammelled black, with bright bolts not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. | 2 | Each | |
| 42 | 42 | Mild steel cold rolled butt hinges (ISI Marked) 'Medium weight' 100 mm size, fixed to steel/angle iron frame by welding, if required complete all as specified and directed by Engr-in- Charge. | 3 | Each | |
| 43 | 43 | 200 mm long mild steel barrel tower bolts, ISI Marked, stove enamelled black, with bright bolt and fixed complete all as specified and as directed. | 2 | Each | |
| 44 | 44 | 150mm mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engr-in-charge. | 2 | Each | |
| 45 | 45 | Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to Fe- 410-O or Fe-310-O, complete all as specified and as directed by Engineer-in-charge. | 30 | Kilogram | |
| 46 | 46 | Solid factory made PVC Door frame of size 50mmx47mm made out of 5mm plain color PVC sheet reinforced with MS Square tube, supply and fixing in opening as per specification and drawings and incluiding making good disturbed surfaces complete all as specified and directed.\nMAKE: SINTEX INDUSTRIES/RAJSHRI PLASTIWOOD LTD / M/S DURA PLAST EXTRACTION PVT LTD / FENESTA / POLYTUFF\n | 4.8 | Running Metre | |
| 47 | 47 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side Prelam PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of single side Prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails having one side feathered edge and on other side 10mm 90 degree bent edge with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and as directed.\nMAKE: SINTEX INDUSTRIES/RAJSHRI PLASTIWOOD LTD / M/S DURA PLAST EXTRACTION PVT LTD / FENESTA / POLYTUFF | 1.3 | Square Metre | |
| 48 | 48 | Mild steel cold rolled butt hinges (ISI Marked) 'Medium weight' 100 mm size, fixed to solid PVC door frame with steel screw, if required complete all as specified and directed by Engr-in- Charge. | 3 | Each | |
| 49 | 49 | Aluminium handles, cast type anodized of size 125 mm, ISI marked, complete all as specified and directed by Engineer-in- Charge. | 2 | Each | |
| 50 | 50 | 150 mm long aluminum ISI marked anodised, barrel tower bolts extruded section, complete all as specified and directed by Engineer-in-Charge | 2 | Each | |
| 51 | 51 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:4, complete all as specified and directed by Engr-in-charge. | 56.4 | Square metre | |
| 52 | 52 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:6, complete all as specified and directed by Engr-in-charge. | 60 | Square metre | |
| 53 | 53 | Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge. | 48 | Square Metre | |
| 54 | 54 | 25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed by Engr-in-Charge. | 32 | Square metre | |
| 55 | 55 | M/L Cement concrete 1:3:6 type C2 using 40mm graded stone crushed aggregate in plinth protection, 50mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete. | 16.5 | Square metre | |
| 56 | 56 | 75 mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base of floors and the like including finishing the surface rough complete all as specified and as directed by Engineer-in-charge. | 32 | Square Metre | |
| 57 | 57 | M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 Square metre but not exceeding 0.11 Square metre, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.\nMAKE: KAJARIA / H&R JOHNSON / CERA / NITCO / SOMANY | 32 | Square metre | |
| 58 | 58 | M&L for 300 x 450 x7 mm thick glazed ceramic tiles colored as in dado/ skirting and vertical surfaces set & jointed in neat cement slurry and pointed in colored cement over and incl 10 mm thick cement mortar 1:4 to match the Shade, pattern, laying etc of tiles complete all as specified and directed.\nMAKE: KAJARIA / H&R JOHNSON / CERA / NITCO / SOMANY | 15.5 | Square metre | |
| 59 | 59 | Steel tubes 15 mm bore, ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.\nMAKE: JINDAL PIPES / TATA / PRAKASH SURYA\n\n | 10 | Running Metre | |
| 60 | 60 | Steel tubes 20 mm bore, ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.\nMAKE: JINDAL PIPES / TATA / PRAKASH SURYA\n\n | 40 | Running Metre | |
| 61 | 61 | Bib taps , fancy type cast copper alloy, chromium plated, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm, complete all as specified and as directed by Engineer-in-charge\nMAKE: PARKO / MARC / ESS ESS / ROCA / CERA / KOHLER | 1 | Each | |
| 62 | 62 | Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete, complete all as specified and as directed by Engr-in-Charge.\nMake: Cera/Hindware/Parryware | 1 | Each | |
| 63 | 63 | 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete all as specified and as directed by Engr-in-Charge.\nMAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE | 1 | Each | |
| 64 | 64 | Viterous china wash basin, white flat back size 550 x 400mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes, PVC connections 15 mm size with PTMT nuts of length 450 mm, complete, all as specified and as directed by Engr-in-Charge.\nMAKE of WHB: CERA/HINDWARE/PARRYWARE\nMake of PVC connection: Prayag/Polytuf/Supreme | 1 | Each | |
| 65 | 65 | Supply and fixing 15mm bore center hole basin mixer with regular spout with pop up waste assembly with 10mm dia 450mm long braided hoses and brass nuts, complete all as specified and as directed by Engr-in-Charge.\nMake : Jaquar Cat Part No CON-167KNB or equivalent of Marc/Kohler | 1 | Each | |
| 66 | 66 | 600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, all as specified and as directed by Engr-in-Charge.\nMAKE: SAINT GOBAIN / MODI GUARD / TRIVENI FLOAT GLASS\n | 1 | Each | |
| 67 | 67 | 110mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to wall with clamps, complete all as specified and as directed by Engr-in- Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL\n | 10 | Running metre | |
| 68 | 68 | 75mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to wall with clamps, complete all as specified and as directed by Engr-in- Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL\n | 5 | Running metre | |
| 69 | 69 | PVC (SWR) bend / shoe, any radius, for 110 mm bore pipe, complete all as specified and as directed by Engr-in-Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL | 2 | Each | |
| 70 | 70 | PVC (SWR) bend / shoe, any radius, for 75 mm bore pipe, complete all as specified and as directed by Engr-in-Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL | 2 | Each | |
| 71 | 71 | PVC (SWR) bend provided with oval access door, any radius, for 110 mm bore pipe, complete all as specified and as directed by Engr-in-Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL | 1 | Each | |
| 72 | 72 | PVC (SWR) vent cowl, any radius, for 75 mm bore pipe, complete all as specified and as directed by Engr-in-Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL | 1 | Each | |
| 73 | 73 | PVC (SWR) floor trap, plain with grating including jointing to waste pipe, 75 mm bore pipe, complete all as specified and as directed by Engr-in-Charge.\nMAKE: SUPREME / ASHIRWAD / FINOLEX / SFMC / ASTRAL | 2 | Each | |
| 74 | 74 | Two coats of cement base paint on new/undecorated wall surfaces including preparation of surfaces and including curing before and after each coat complete all as specified.\nMAKE: SNOWCEM / ASIAN / BERGER / DURACEM\n | 60 | Square Metre | |
| 75 | 75 | Preparing new plastered wall surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge. | 54 | Square\nMetre | |
| 76 | 76 | Preparing new plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge. | 32 | Square\nMetre | |
| 77 | 77 | Preparation of new or previously untreated steel or steel based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.\nMAKE: NEROLAC PAINTS / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS | 10 | Square Metre | |
| 78 | 78 | Supply and fixing Salt glazed stoneware (SGSW) grade 'A' drain pipes 150 mm bore laid and jointed on concrete bed, jointed in cement mortar 1:1, complete including testing etc all as specified and shown on drgs (concrete bed shall be measured and paid for separately). | 5 | Running metre | |
| 79 | 79 | Material and labour for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150 mm bore pipes complete all as specified and as directed. | 5 | Running metre | |
| 80 | 80 | Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, complete all as specified and as directed by Engr-in-Charge.\nMAKE: SINTEX / POLYWELL / ROTEX POLYCON | 1 | Each | |
| 81 | 81 | Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, suitable for 20mm bore dia of pipe, complete all as specified and as directed by Engr-in-Charge.\nMAKE: PARKO / MARC / ESS ESS / ROCA / CERA / KOHLER\n | 1 | Each | |
| 82 | 82 | Tubular towel rails brass chromium plated, 20 mm dia, D type, 60 cm long between flanges, fixed with rawl plugs, complete alll as specified and as directed, | 1 | Each | |
| 83 | 83 | Material and labour for 12.50 mm thick Gypsum ceiling with glass fiber tissue Gypsum board tiles tissued with pin hole in random pattern of size 595mm x595mm and GI channel/angle/tee section works as in ceiling fixed with screws as per manufacturer's instructions including necessary hanging arrangement to hold ceiling with roof complete as per all as specified and dirceted.\nMAKE: INDIA GYPSUM LTD / GYPROC / EVEREST / ARMSTRONG | 24 | Square Metre | |
| 84 | 84 | Supply and fixing soap dish, stainless steel fancy type, fixed to plugs with chromium plated brass screws complete all as specified and dirceted. | 1 | Each | |
| 85 | 85 | Point wiring concealed with 1.5 Sqmm copper conductor cable (multistrand) PVC insulated FRLS (unsheathed), drawing in and including PVC casing caping having wall thickness not less than 2 mm with sunk cast iron/pressed steel terminal boxes made out of 1.2 mm thick sheet including one coat red oxide primer on internal and external surface covered with 3 mm thick hylam brand IS-2036 marked laminated sheet cover (for mounting switches, sockets, regulators etc), including 1.5 Sqmm PVC insulated (multistranded) FRLS copper conductor continuous earth wire for one light point controlled by one switch one way complete all as specified and directed.\nMAKE OF CABLE: L&T / FINOLEX / GRANDPLAY / ANCHOR / POLYCAB\nMAKE OF PVC CASING/CAPING: PLAZA / FINOLEX / SUPREME / PRESTO PLAST\n | 20 | Point | |
| 86 | 86 | All as per ser item No 85.00 here-in-before but for one bell point controlled by one bell push complete all as specified and as directed by Engineer-in-Charge.\nMAKE OF CABLE: L&T / FINOLEX / GRANDPLAY / ANCHOR / POLYCAB\nMAKE OF PVC CASING/CAPING: PLAZA / FINOLEX / SUPREME / PRESTO PLAST | 1 | Point | |
| 87 | 87 | All as per ser item No 85.00 here-in-before but for 3 pin socket outlet 5 amp independent with cable of size 1.50 sqmm for point wiring and 1.50 sqmm as in contineous earth wire complete all as specified and as directed by Engineer-in-Charge.\nMAKE OF CABLE: L&T / FINOLEX / GRANDPLAY / ANCHOR / POLYCAB\nMAKE OF PVC CASING/CAPING: PLAZA / FINOLEX / SUPREME / PRESTO PLAST | 10 | Point | |
| 88 | 88 | All as per ser item No 85.00 here-in-before but for 3 pin socket outlet 15 amps independent with cable of size 2.50 sqmm for point wiring and 1.50 sqmm as in contineous earth wire complete all as specified and as directed by Engineer-in-Charge.\nMAKE OF CABLE: L&T / FINOLEX / GRANDPLAY / ANCHOR / POLYCAB\nMAKE OF PVC CASING/CAPING: PLAZA / FINOLEX / SUPREME / PRESTO PLAST | 6 | Point | |
| 89 | 89 | Supply and fixing switch piano button flush type, single pole one way 6 amps complete all as specified and directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 30 | Each | |
| 90 | 90 | Supply and fixing switch bell push piano flush button single pole one way 5 amps 6 amps complete all as specified and directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 1 | Each | |
| 91 | 91 | Supply and fixing switch piano button flush type, single pole one way 16 amps complete all as specified and directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 6 | Each | |
| 92 | 92 | Supply and fixing 5 pin socket outlet 2 in 1, 2 and 3 pin, 5 amps flush type complete all as specified and directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 10 | Each | |
| 93 | 93 | Supply and fixing 5 pin socket outlet 2 in 1, 2 and 3 pin, 5 and 15 amps flush type complete all as specified and directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 6 | Each | |
| 94 | 94 | Supply and fixing ceiling rose, 3 phase on PVC square blocks surface bakelite 65 x 50 mm, 3 terminal complete all as specified and as directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 8 | Each | |
| 95 | 95 | Supply and fixing Call bell ding dong AC, 23 Volts, single pole type complete all as specified and as directed by Engineer-in-Charge.\nMAKE: ANCHOR / LEGRAND / CRABTREE / HAVELLS | 1 | Each | |
| 96 | 96 | Supply and fixing universal batten suitable for LED tube rod suitable for T8 Lamp including LED T8 polycarbonate tube rod 18 watt complete all as specified and as directed by Engineer-in-Charge.\nNote :(i) A certificate from the manufactures for warranty minimum upto 3 years shall be obtained and submitted to the AGE.\n(ii) Any touch up of the existing surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department.\nMake: REGALBATTENT5UPTO1X18DSBSWH OF Havells or equal approved in CG/Bajaj/Phillips | 5 | Each | |
| 97 | 97 | Supply and fixing lamp holder insulated body with back plate with LED lamp 08 watt complete all as specified and directed by Engineer-in-Charge. \nMake: Havells/CG/Bajaj/Phillips/Anchor/Crabtree | 4 | Each | |
| 98 | 98 | Supply and fixing MCB distribution board double door 240 volts SPN 4 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc complete all as specified and as directed by Engineer-in-Charge.\nMake: Cat part No 5076 10 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32) | 1 | Each | |
| 99 | 99 | Supply and fixing MCB SPN 32/40 Amps, 230 V,AC complete all as specified and as directed by Engineer-in-Charge.\nMake: Cat part No 4086 18 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4) | 1 | Each | |
| 100 | 100 | Supply and fixing MCB SP 5 to 32 Amps, 230 V A/C complete all as specified and as directed by Engineer-in-Charge.\nMake: Cat part No 4085 87 to 4085 95 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4) | 10 | Each | |
| 101 | 101 | Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm, 4 core, complete all as specified and directed by Engr-in-Charge.\nMAKE: FINOLEX / UNIVERSAL / KEI INDUSTEIES PVT LTD / POLYCAB / GLOSTER\n\n | 100 | Running Metre | |
| 102 | 102 | Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 4 mm dia galvanised earth lead wire by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel all as specified or indicated in electrical plate no 3 of MES Part-I, including testing on completion including the material and labour of the following :- | 6 | Each | |
| 103 | 102.01 | (a) Excavation and earth work for drilling hole for electrode in any type of soil. | |||
| 104 | 102.02 | (b) PCC pit in cement concrete 1:2:4 type B-1. | |||
| 105 | 102.03 | (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. | |||
| 106 | 102.04 | (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. | |||
| 107 | 102.05 | (e) 15 mm nominal bore light grade GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. | |||
| 108 | 102.06 | (f) Requisite quantity of common salt and charcoal. | |||
| 109 | 102.07 | (g) Testing of earthing. | |||
| 110 | 102.08 | Note : (a) On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.\n(b) The contractor shall quote his rate considering taking down cost of existing unserviceable earthing. | |||
| 111 | 103 | Supply and Fixing GI tubing light grade 40mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles, complete all as specified and as directed by Engr-in-Charge.\nMAKE: JINDAL PIPES / TATA / PRAKASH SURYA | 26 | Running metre | |
| 112 | 104 | Sub class 'B' old size bricks well burnt as covering to under ground cables , laid dry, flat over the cables on sand cushioning with width equal to length of the brick as mechanical protection to cable, complete all as specified and directed. | 1.3 | Per 1000 Nos | |
| 113 | 105 | Dry coarse sand as cushioning to under ground cable provided with layer of 8 cms deep before laying the cable and 15 cms deep after laying and stretching the cable, punned to 18 cm thick complete all as specified and as directed by Engr-in-Charge. \nNOTE Only punned thickness shall be measured for payment purpose. | 12 | Cubic metre | |
| 114 | 106 | Supply and fixing 2'x2' LED Panel 36/40 watt, Ultra modern designed architectural LED luminaire which provides soft-light and glare free symmetrical illumination suitable for Armstrong/Grid ceiling, powder coated white CRCA full glow LED light fitting including 3 core flexible wire from ceiling rose to fitting etc. all as specified and directed by Engineer-in-Charge.\nNote :(i) A certificate from the manufactures for warranty minimum upto 3 years shall be obtained and submitted to the AGE/GE\n(ii) Any touch up of the existing surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department.\nMake: VENUSNEOHE2X2PLR36WLED8XXS of Havells or equal approved in C&S/Syska | 6 | Each | |
| 115 | 107 | Supply and fixing wall mounted fan AC single phase of 400 mm sweep, copper wounded, 230 volts, 50 Hz, suitable for wall mounting complete all as specified and as directted by Engineer-in-Charge.\nMAKE: Model D'zire of Havells or equal approved in Usha/Orient/Khaitan | 4 | Each | |
| 116 | 108 | Exhaust fan, AC, 150mm sweep, copper wound, non metallic body with all accessories such as louvers, nuts, bolts and washers including cutting holes of suitable size in brick/stone walls for fixing the exhaust fan including making good the disturbed surface to match with the existing finishes complete all as specified and directed by Engineer-in- Charge.\nMake: Cat part No VENTIL AIR-DXR of Havells or equal approved make in Usha/Orient/Khaitan | 6 | Each | |
| 117 | 109 | Supply and fixing MCB distribution board, TPN, double door with IP-43 protection suitable for MCCBs as incommer and MCB as outgoing, 415 volts 3 Phase 50 Hz, 4 way complete with suitable capacity copper bus bar and neutral link complete with one MCCB 3 pole 415 volts 63 amps rating with rupturing capacity 25 KA of the same make of DB concealed to wall including cutting chases to wall for making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc complete all as specified and as directed by Engineer-in-Charge. (MCCB as incommer is included in overall quoted rates and MCBs as outgoing shall be measured and paid seperately as \"supply and fixing\" under relevant items\nMake fo DB: Cat part No 5077 40 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)\nMake of MCCB: Legrand (DPX³) Cat Part No 4200 33 or equal approved in Siemens (3VL)/Schneider (NSX)/L&T (D-Sine) | 1 | Each | |
| 118 | 110 | Supply and fix sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20Amps, 240V complete with one single pole MCB of any cap from 5 to 32 Amps of breaking capacity 10KA, complete all as specified and as directed by Engr-in-Charge.\nMake : Legrand/L&T/Schneider/ABB | 3 | Each | |
| 119 | 111 | M&L for surface sub main wiring with two run of 6.00 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLS cable in and including electrical grade PVC casing-caping of desired size and colour not less than 1.2 mm thick & 4.00 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed \nMake of wire-- Finolex/Havells/Plaza. | 40 | Running Metre | |
| 120 | 112 | Supply and fixing of Anti static Vinalyl Mat (Electrostatic discharge Mat) of thickness 2 mm, 3 layer complete all as specified and directed. | 25 | Square Metre | |
| 121 | 113 | Supply and fixing of flooring copper tap (self adhesive) of thickness 0.08 mm and width 20mm for ESD Grounding complete all as specified and directed. | 30 | Running Metre | |
| 122 | 114 | Dismantling existing LT panel and taking out existing LT cable of size upto 300 sqmm any core without making damage to existing electrical system, refixing the dismantled LT panel to another location (within the range of 15 mtr) as directed, including PCC ffoundation 1:3:6 type C-2 using 40 mm graded crushed stone aggregate) of required size (as per existing foundation made at old location), laying of retrived LT cable and making electrical connection to LT Panel including testing and commissioning of LT Panel complete all as specified and as directed by Engineer-in-charge.\nNOTE: Cost of earth work, bricks sand, returning filling, removal and PCC work included in the quoted rate against this item. | 1 | Each Job | |
| 123 | 115 | Supply and fixing MCCB three pole 415V 200 Amps, 36 kA complete all as specified and as directed by Engineer-in-Charge.\nMake: Cat part No 4202 38 of Legrand (DPX³) or equal approved in Schneider (NSX)/Siemens (3VL2)/L&T (D-Shine) | 1 | Each | |
| 124 | 116 | Supply and fixing installation, commisssioning and testing factory made CPRI approved, outdoor cubical type feeeder pillar box totally enclosed (over all size not less than the size to accommodate the INCOMING and OUT going accessories), fabricated with 3.15 mm thick CRCA sheet (Heavy duty) over a frame of 50 x 50 x 6mm angle iron and mounted on platform all around and dust and vermin proof, IP-65 protection, back side openable, fixed with nuts and bolts and front side openable with hinged shutter and locking arrangement by operate alen key individuals for MCCBs and overall front panel double door shutter with powder coated finished both internally and externally suitable for 415 volts, AC, 50 Hz, 3 Phase, 4 Wire system by means of copper bus bar of size 50 x 5mm (Main) duly wrapped with coloured insulating tape/sleeves mounted on porcelain insulators with provision of fixing MCCBs necessary inter connections with copper strips of size 30 x 5mm and providing following equipments including connection with all incoming/outgoing calbes of different size duly crimping with suitable size copper lugs and PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as per the recommandation of manufacturer including earth work complete all as specified and as directed by Engr-in-Charge: - | 1 | Each Set | |
| 125 | 116.01 | INCOMING:\n(a) Bus bar chamber comprising 4 Nos copper strip bus bars PVC insulated made of copper strip of size 50 x 5mm, PVC sheathed with colour coding\n(b) MCCB, 160 Amps, 4 pole, 415 V, 36 KA, complete with spreader links -01 No, Make: Legrand / L&T / Schneider\n(c) Multifunctional digital panel meter with LCD display flush mounted type of size 96 x 96mm, accuracy class 1, suitable for CTs with secondary current 5A having provision of display parameters such as voltage, Amp, Frequency, Power facttor, KW, KV, etc - 01 No.\n(d) Current transformer of ratio 200/5 amps, current rating primary upto 200 amps and secondary 5 amps, accuracy class 1, VA burden 10 VA including necessary wiring using PVC insulated copper conductor cable of appropriate size as per standard engineering practice - 01 Set of three.\nOUTGOING:\n(a) MCCB having current rating 63 Amps, three pole, 415 V, 25 KA, 50Hz with spreader links-04 No, Make: Legrand/L&T/Schneider. (Distribution of MCCB: Equipment load-01 No MCCB, Light + power point + AC - 01 No MCCB and Spare MCCB - 02 Nos) | |||
| 126 | 117 | Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm, 3.5 core, complete all as specified and directed by Engr-in-Charge.\nMAKE: FINOLEX / UNIVERSAL / KEI INDUSTEIES PVT LTD / POLYCAB / GLOSTER\n | 100 | Running Metre | |
| 127 | 118 | Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm, 3.5 core, complete all as specified and directed by Engr-in-Charge.\nMAKE: FINOLEX / UNIVERSAL / KEI INDUSTEIES PVT LTD / POLYCAB / GLOSTER\n | 60 | Running Metre | |
| 128 | 119 | Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 32 x 6 mm galvanised earth strip by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel all as specified or indicated in electrical plate no 3 of MES Part-I, including testing on completion including the material and labour of the following :- | 4 | Each | |
| 129 | 119.01 | (a) Excavation and earth work for drilling hole for electrode in any type of soil. | |||
| 130 | 119.02 | (b) PCC pit in cement concrete 1:2:4 type B-1. | |||
| 131 | 119.03 | (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. | |||
| 132 | 119.04 | (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. | |||
| 133 | 119.05 | (e) 40 mm nominal bore light grade GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. | |||
| 134 | 119.06 | (f) Requisite quantity of common salt and charcoal. | |||
| 135 | 119.07 | (g) Testing of earthing. | |||
| 136 | 119.08 | Note : (a) On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.\n(b) The contractor shall quote his rate considering taking down cost of existing unserviceable earthing. | |||
| 137 | 120 | Gun-metal, globe or gate valves, ISI marked, with iron wheel head, screwed both ends for iron pipe of size 20mm, complete all as specified and as directed by Engr-in-Charge | 1 | Each | |
| 138 | 121 | Cutting existing steel tubing 25 or 32 mm dia for alterations or additions (Each cut measured), done in position without taking down the existing pipe line complete all as specified and directed by Engr-in-charge. | 1 | Each | |
| 139 | 122 | Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 32 x 6 mm galvanised earth strip by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel all as specified or indicated in electrical plate no 3 of MES Part-I, including testing on completion including the material and labour of the following :- | 8 | Each | |
| 140 | 122.01 | (a) Excavation and earth work for drilling hole for electrode in any type of soil. | |||
| 141 | 122.02 | (b) PCC pit in cement concrete 1:2:4 type B-1. | |||
| 142 | 122.03 | (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. Earth pit cover (HDPE/FRP) shall be measured and paid seperately as \"Supply and fixing\" under relevant item here-in-after | |||
| 143 | 122.04 | (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. | |||
| 144 | 122.05 | (e) 40 mm nominal bore light grade GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. | |||
| 145 | 122.06 | (f) Requisite quantity of common salt and charcoal. | |||
| 146 | 122.07 | (g) Testing of earthing. | |||
| 147 | 122.08 | Note : (a) On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge.\n(b) The contractor shall quote his rate considering taking down cost of existing unserviceable earthing. | |||
| 148 | 123 | Supply and fixing HDPE/FRP earth pit cover of internal size not less than 300 x 300 mm with top openable cover with handle and one side hinges, provision of entry/exit of earth strip at side complete all as specfied and directed.\nMAKE: True Power Earthing/Dhruva Tech. | 8 | Each | |
| 149 | 124 | Supply and fixing of test point terminal block of gun metal or phosphorus bronze of size 75 x 75 x 25mm, drilled and screwed including 3 Nos, 8 mm dia 25 mm long hex head screws complete all as per specified and as directed. | 8 | Each | |
| 150 | 125 | Supply and fixing galvanised iron strip of size 32 x 6mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as per specified and as directed. | 35 | Square metre | |
| 151 | 126 | SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
