annual plan-lpgp 2025-26 phc perur renovation (cfc+mgnr -rs 2,60,000/-)-pro.no.120/25-26-general civil work- 1 sheet roofing 2 15.31:dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 3 12.50:providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer-in-charge. the sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with epdm seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 4 12.51.1:providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :ridges plain (500-600 mm) 5 10.16.1:steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.hot finished welded type tubes 6 10.1:structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 7 partition work 8 15.57:dismantling aluminium / gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 metres lead as directed by engineer - in-charge 9 21.1.1.2:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 10 21.1.2.2:for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings shall be paid for separately)powder coated aluminium (minimum thickness of powder coating 50 micron) 11 21.3.1:providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 12 21.2.2:providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is : 12823 grade i type ii, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer - in- charge.pre- laminated particle board with decorative lamination on both sides