tender for annual plan-2025-26 eriyad gp ayurveda hospital maintenance pro 179/25-179/25-general civil work --1 subcentre maintanance 2 21.1.1.2:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 3 od307147/2025-2026:providing and fixing hylam board-2mm thick- in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge 4 51.2.3:filling with quarry muckfilling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the cbr value of subgrade 5 od319586/2025-2026:flooring with interlocking cabbles 60mm thick (premium) minimum strength 40kg/cm2 over a bed of 6mm metal filling in 50mm average thick and compacting using earth hammer/ compacting machine hand operated including cost and conveyance of all materials labour charges, pointing edges etc complete 6 4.1.3:providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-iii)derived from natural sources : 4 graded stone aggregate 20 mm nominal sizederived from natural sources) 7 od307143/2025-2026:providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.35mm (+0.05%), total coated thickness with zinc coating 120gms per sqm as per is:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12m or as desired by engineer-in-charge. the sheet shall be fixed using self drilling / self tapping screws of size (5.50x55mm( with epdm seal complete upto any ptich in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 8 10.16.1:steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.hot finished welded type tubes 9 od307149/2025-2026:engaging man coolie 10 14.1.1:repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 meters lead:with cement mortar 1:4 ( 1 cement : fine sand) 11 od307867/2025-2026:providing and fixing on eave face upvc half cut rain water gutter pipes (150mm 4kg/cm2) with all necessary fittings with clamps at 1 m intervel (12.41.2 modified) 12 18.12.6:providing and fixing g.i. pipes complete with g.i fittings including trenching and refilling etc. external work50 mm dia nominal bore 13 13.88:removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 14 13.98.1:wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:one or more coats on old work 15 13.99.1:painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give an even shade :one or more coats on old work 16 9.63.3:providing and fixing isi marked oxidised m.s. tower bolt black finish, (barrel type) with necessary screws etc. complete : (copper oxidized as per is : 1378)150x10 mm 17 9.66.2:providing and fixing isi marked oxidised m.s. handles conforming to is:4992