tender for road signage work on 17x30m. span setu situated on km. 2 and 3 of saifni chandpur kala road in distt. rampur. - type-a, w: metal beam crash barrier providing and erecting a w metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ismc senes channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to 15:1367 and is:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm. 330 mm long complete as per clause 810 2 road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface. providing and laying of hot applied, thermoplastic compound 2.5 mm thick including reflectorising glass beads 250 gms per som area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35-2015 the finished surface to be level, uniform and free from streaks and holes. 3 road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface. (repeated/tranvers bar) providing and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads 500 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per irc:35-2015 the finished surface to be level, uniform and free from streaks and holes. 4 solar power road marker (solar studs) the solar studs shall be made of aluminium alloy and poly carbonate material which shall be absolutely weather resistant and strong enough to support a load of 13,635 kg tested in accordance with astm d4280. its colour may be white, red, yellow, green or blue or combination as directed by the engineer its water resistance shall meet the requirements of ip 65 in accordance with is:12063:1987 category 2 for protection against water ingress. the dimensions of solar studs shall not be less than 100 mm x 100 mm x 10 mm it shall have super bright leds so as to provide long visibility from a distance of more than 800 m. its flashing rate shall not be less than 1 hz. its should be able to give the prescribed performance in the temperrature range of -40°c to +55°c. its life shall be not less than 3 years. the rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all.complete as per direction of the engineer-in-charge 5 cat eyessupply & fixing of moulded cats eye shank raised pavement markers made of polycarbonate moulded body and reflected pannel with micro prismatic lens capable of providing total internal reflection of the light entering the lens face conforming to astmd for 4280 type h and complying to specification of categories a of morth circular no rw/nh/33023/10-07-do-iii 11-06-1997. the height, width and length shall not exceed 20 mm 150 mm and 105 mm and with minimum relfective area of 13 sqcm. and the each side slope to the base shall be 350. fixing will be without nails but using with twin polymer shanks bitumen adhesive on bitumen roads as per manufactures recmmendation including site clearence etc. and complete as per direction by e/i. 6 road delinator delineator supply & fixing of m s delineator made of mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron for protection against corrosion the surface should be conceated so that there should not be any exposed surface without powder coating. alternatively, these metal guide poles can be concealed with thermoplastic body. the posts shall have lan ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto the ground. mid steel guide poles shall conform to type xi sheeting specifications as per irc:67 and astm d4956 which would ensure to obtainl clear visibility of the road alignment during night time. the retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international/govemment laboratory/institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from indian condition within 3 years of launching of product by the manufacture in abroad. alternatively, a certificate conforming to astm specification (d4956-09) on artificial accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally. in such a situation, the employer/client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per irc 67:2012 & proof of the same report shall be uploaded which quoting tender. the rate shall include all materials, labour, t&p, transportation, installation and incidentals all complete as per direction of the engineer-in-charge