one panchayath one playground - development of ground in sathyan nagar estate ward in nemom lac, thiruvananthapuram - supply and installation of outdoor gym equipment - retender outdoor gym equipment , gym equipments (18% gst) , od40855/2025-2026 : horse rider - supply and installation of horse rider having the following specifications: dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - ø 114 mm od “b” class gi pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. foundation cover cap -dome shape of pp / nylon / hdpe material. remaining frame – is made by ø 48 mm od “b” class gi pipe. seat frame – is madeby ø 48 mm od “b” class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of ø 48 mm od “b” class g.i. pipe. angle between link and ground position is 10-20 degree. handle - ø 33 mm od “b” class gi pipe. paddle vertical support - ø 60 mm od “b” class gi pipe. handle frame- ø 42 mm od “b” class gi pipe dually bending design. foot pipe - ø 33 mm od “b” class gi pipe. support frame – 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe. bearing bush closing cap – pp /nylon / hdpe material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand. bearing bushes - ø 60mm od seamless pipe. pin – made of ø 25 mm m.s. bright bar. grips - high quality rubber ø 46 mm od. circlips – a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. , od40856/2025-2026 :back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from ø 88 mm od “b” class g.i. pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. leg support - ø 42 mm od “b” g.i pipe. seat rest pipe – ø 42 mm od “b” class g.i pipe. handle pipe – ø 33 mm od “b” class g.i pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe – ø 42 mm od “b” class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap – pp / nylon / hdpe material. seat – 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber ø 46 mm od. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing , od40857/2025-2026 : sky walker - supply and installation of sky walker having the following specifications: dimensions: (l x w x h) 1720 x 910 x 1700 mm. main frame - made of ø 88 mm od “b” class gi pipe dually bending design. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. paddle vertical support - ø 42 mm od “b” class gi pipe. handle - ø 33 mm od “b” class gi pipe dually bending design. leg movement frame – 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use for to support it. top closing cap – dome shape made by pp / nylon / hdpe material. closing cap’s– pp / nylon / hdpe material. foundation stool: made from main pipe ø 88 mm m.s pipe. and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. grips - high quality rubber ø 46 mm od. bearing- use is 6005 permanent lubricated reputed brand. bearing bushes - ø 60 mm od seamless pipe. pin –made of ø 25mm m.s. bright bar. circlips – a 24 circlips are used for assembly. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing , od40858/2025-2026 :shoulder builder (double) - supply and installation of double shoulder builder having the following specifications: dimensions: (l x w x h) 890 x 558 x 1500 mm. main frame - made from ø 114 mm od “b” class g.i. pipe. foundation plate –m.s. round plate of ø 250 mm & 8 mm thick. foundation cover cap - dome shape of pp / nylon / hdpe material. shoulder ring pipe - ø 33 mm od “b” class g.i pipe. shoulder ring pipe support – ø 25 mm od “b” class g.i pipe. nylon knob with bearing – is fixed on shoulder ring pipe for rotating purpose (2 set to be fixed in a position for kids and adults). top closing cap’s- pp / nylon / hdpe material. closing cap – pp / nylon / hdpe material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brands.pin – ø 25mm m.s. bright bar pin. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. bearing bushes - ø 60 mm od seamless pipe. circlips – a 24 circlips are used for assembly.coating - best quality of powder coating 80 -120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing , od40859/2025-2026 :leg press (double) -supply and installation of double leg press having the following specifications: dimensions: (l x w x h) = 1676 x 400 x1500 mm. main frame - ø 114 mm od “b” class gi pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. foundations cover cap - dome shape of pp / nylon / hdpe material. link - is ø 60 mm od “b” class gi pipe. seat frame - ø 42 mm od “b” class gi pipe. leg press back rest should be angled in 120 -130 degree. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 2 mm thick use to support it. seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 in-sert wall thickness 3 to 4 mm. link connected with frame by 8mm thick laser cutting ms profile. top closing cap – dome shape made by pp /nylon / hdpe material. closing cap’s- pp / nylon / hdpe material. foundationstool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brand. pin– ø 25 mm m.s. bright bar pin. bearing bushes - ø 60 mm od seamless pipe. circlip– a 24 circlips are used for assembly. coating - best quality of powder coating 80 -120 micron. safety instructions and exercise chart -start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing , od40860/2025-2026 : triple twister - supply and installation of triple twister (standing position - 2 and seating position - 1) having the following specifications: dimensions: (l x w x h) 1500 x 1500 x 1420 mm. main frame – ø 114 mm od “b” class gi pipe. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. seat plate support – ø 60 mm od “b” class g.i pipe. seating ring - ø 33 mm od b class g.i pipe made by rolling. seating ring support - ø 33 mm od “b” class g.i pipe. remaining frame – is made by 100 x50 x 2.5 mm rectangular pipe. standing plate- ø 300 mm od x 10 mm thick m.s. plate. seating plate- ø 300 mm od x 10 mm thick m.s. plate. seating seat position and other two standing position plates are fixed 120 degrees each from other. handle – ø 33 mm “b” class g.i. pipe made by rolling. top closing cap – dome shape made by pp / nylon / hdpe material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - used is 6005 permanent lubricated reputed brand. bearing bushes - ø 60 mm od seamless pipe. pin – made up of ø 25mm m.s. bright bar. circlips– a 24 circlips are used for assembly. coating - best quality of powder coating 80 -120 micron. safety instructions and exercise chart - start &finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. , od40861/2025-2026 :chest press (double) - supply and installation of double chest press having the following specifications: dimensions: (l x w x h) 1955 x 710 x 1900 mm. main center pipe - ø 114 mm od “b” class gi pipe. foundation plate –m.s. round plate of ø 250mm & 8 mm thick. foundations cover cap dome shape of pp / nylon / hdpe material. remaining frame - made up of ø 48 mm od “b” class g.i. pipe.handle - made up of oslash;48mm od “b” class g.i. pipe. link - made up of ø 48 mm od “b” class g.i. pipe. seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 in-sert wall thickness 3 to 4 mm. bearing bush closing cap’s– pp / nylon / hdpe material. handle must be connected with frame by 8 mm laser cutting ms profile. top closing cap – dome shape made by pp / nylon / hdpe material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brands. pin – made up of ø 25 mm m.s. bright bar pin. bearing bushes -ø 60 mm od seamless pipe. grips - high quality rubber ø 46 mm od. circlips–a 24 circlips are used for assembly. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart -start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing , od40862/2025-2026 :air walker - supply and installation of air walker having the following specifications: dimensions: (l x w x h) 1190 x 380 x 1244 mm. main frame- ø 88 mm od “b” class gi pipe dually bending design. foundation plate –m.s. round plate of ø 250 mm & 8 mm thick. paddle– ø 42 mm od round gi pipe. handle – ø 33mm od “b” class gi pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use to support it. top closing cap – dome shape made by pp / nylon / hdpe material. closing cap’s - pp / nylon / hdpe material. bracket - 8 mm thick laser profile is use to support paddle frame. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearinguse is 6005 permanent lubricated reputed brands. pin’s – ø 25mm m.s. bright bar pin. circlips– a 24 circlips are used for assembly. bearing bushes -ø 60 mm od seamless pipe. coating - best quality of powder coating80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing , od67637/2025-2026 :arm and paddle bike - supply and installation of arm and paddle bike having the following specifications: dimensions: (l x w x h) 990 x 500 x 880 mm. main frame –100 mm x 50 mm x 2.5 mm rectangular cr pipe with bending design. foundation plate – m.s. round plate of ø 250 mm & 8 mm thick. handle – ø 33 mm od “b” class gi round pipe dully bending design. side and top cover – 1.6 mm thick ms laser cutting profile is used. seat – 380 x 275 x 60 mm thick hdpe blow moulding. paddle –100 mm x 50 mm capsule pipe and 40 x 16 mm ms flat should be used for connecting the paddle and shaft. closing cap’s – pp / nylon / hdpe material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing bushes - ø 60 mm od seamless pipe. bearing - use is 6005 permanent lubricating sealed reputed brand. shaft -made up ofø25mm od ms bright bar. circlips– a 24 circlips are used for assembly. coating - best quality of powder coating 80 -120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. , od67654/2025-2026 :single bar - supply and installation of single bar having the following specifications: dimensions: (l x w x h) 3550 x 2590 mm. main frame - made from ø 48 mm od b class g.i. pipe. frame of single bar - ø 33 mm od b class g.i. pipe. foundation plate - m.s. round plate of ø 250 mm & 8 mm thick. top closing caps - decent design size pp / hdpe /ms. material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart made from aluminum / stainless-steel stick-on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing