supply of fittings fabricated from plate-cs_as_ss supply of fittings fabricated from plate-cs_as_ss for p25 project at iocl panipat refinery , supply of fittings fabricated from plate - c.s. , elb,90 deg,lr,cs (h2 ser.), b16.9, bw ends,sch 30, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs, b16.9, bw ends,sch 40, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs (nace+h2), b16.9, bw ends,sch 40, lw,100% radiography, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,cs (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,90 deg,lr,cs (galv.), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs (galv.), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,cs (ibr), b16.9, bw ends,sch 30, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,90 deg,lr,cs (ibr), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,90 deg,lr,cs (ibr), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,90 deg,lr,cs (ibr), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,90 deg,lr,cs (ibr), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,90 deg,lr,cs (ibr), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs (nace+h2), b16.9, bw ends,sch xs, lw,100% radiography, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005 , elb,45 deg,lr,cs (galv.), b16.9, bw ends,sch std, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,cs (ibr), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,45 deg,lr,cs (ibr), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,45 deg,lr,cs (ibr), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , elb,45 deg,lr,cs (ibr), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required , mitre bend,90deg,1.5d,5 pieces, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,90deg,1.5d,5 pieces, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,90deg,1.5d,5 pieces, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,90deg,1.5d,5 pieces, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,90deg,1.5d,5 pieces, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,45deg,1.5d,3 pieces, tkis drawing, bw ends,sch std, lw, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,45deg,1.5d,3 pieces, tkis drawing, bw ends,sch std, lw, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,45deg,1.5d,3 pieces, tkis drawing, bw ends,sch std, lw, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , mitre bend,45deg,1.5d,3 pieces, tkis drawing, bw ends,sch std, lw, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for details of mitered elbow refer, doc. 6745-pip-000-tb-0003 , con red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , con red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , con red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , con red,cs (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , con red,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , tee,cs (h2 ser.), b16.9, bw ends,sch 30, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch 40, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs (nace+h2), b16.9, bw ends,sch 40, lw,100% radiography, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 4.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs (nace+h2), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 4.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for run size , tee,cs (galv.), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , ecc red,cs (h2 ser.), b16.9, bw ends,sch 30, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,cs (h2 ser.), b16.9, bw ends,sch 30, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch std, lw,100% radiography, maximum hardness in weld joint, shall be limited to 200 bhn, all welds shall be stress, releived, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs, b16.9 similar, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w s9, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch 40, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (nace+h2), b16.9, bw ends,sch 40, lw,100% radiography, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 4.schedule indicated is for higher size , ecc red,cs (nace+h2), b16.9, bw ends,sch 40, lw,100% radiography, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 4.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (nace+h2), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 4.schedule indicated is for higher size , ecc red,cs (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,cs (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch xs, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs, b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (nace), mss sp-75, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , ecc red,cs (nace), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.nace req. acc. to nace mr-0103, and doc. 6745-pip-000-ec-0005, 3.schedule indicated is for higher size , field mfg. ecc red,cs, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3.for details of field manufactured, eccentric reducers refer, doc.6745-pip-000-tb-0005. , field mfg. ecc red,cs, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3.for details of field manufactured, eccentric reducers refer, doc.6745-pip-000-tb-0005. , field mfg. ecc red,cs, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3.for details of field manufactured, eccentric reducers refer, doc.6745-pip-000-tb-0005. , field mfg. ecc red,cs, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3.for details of field manufactured, eccentric reducers refer, doc.6745-pip-000-tb-0005. , field mfg. ecc red,cs, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3.for details of field manufactured, eccentric reducers refer, doc.6745-pip-000-tb-0005. , field mfg. ecc red,cs, tkis drawing, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a672 gr.b60 cl.12, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3.for details of field manufactured, eccentric reducers refer, doc.6745-pip-000-tb-0005. , ecc red,cs (galv.), b16.9, bw ends,sch std, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (galv.), b16.9, bw ends,sch std, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (galv.), b16.9, bw ends,sch std, a234 gr.wpb-w(galv.), add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,cs (ibr), b16.9, bw ends,sch std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required, 3.schedule indicated is for higher size , ecc red,cs (ibr), b16.9, bw ends,sch non-std, lw,100% radiography, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.ibr certificate in form iiic required, 3.schedule indicated is for higher size , supply of fittings fabricated from plate - a.s. , elb,90 deg,lr,as, b16.9, bw ends,sch std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp9-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp9-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp9-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,as (h2 ser.), b16.9, bw ends,sch 30, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,as (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,90 deg,lr,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,as, b16.9, bw ends,sch std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,as (h2 ser.), b16.9, bw ends,sch 30, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,as (h2 ser.), b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , elb,45 deg,lr,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004 , con red,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , tee,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp9-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , ecc red,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp5-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp9-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as, b16.9, bw ends,sch xs, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp9-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , ecc red,as (h2 ser.), b16.9, bw ends,sch non-std, lw,100% radiography, normalized & tempered, radiography shall be done, after stress relieving, weld factor e = 1.00, a234 gr.wp11-w cl.1, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.additional requirements for h2 service, acc. to doc. 6745-pip-000-ec-0004, 3.schedule indicated is for higher size , supply of fittings fabricated from plate - s.s. , elb,90 deg,lr,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp304-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,90 deg,lr,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , elb,45 deg,lr,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001 , con red,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp304-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , tee,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp304-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , tee,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for run size , ecc red,ss,dual, b16.9, bw ends,sch 80s, lw,100% radiography, weld factor e = 1.00, a403gr.wp304/304l-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size, 3. shall be dual certified , ecc red,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp304-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , ecc red,ss, b16.9, bw ends,sch 10s, lw,100% radiography, weld factor e = 1.00, a403 gr.wp316-wx, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.schedule indicated is for higher size , supply of fittings fabricated from plate - c.s. - epoxy coated , elb,90 deg,lr,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,90 deg,lr,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,90 deg,lr,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,90 deg,lr,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,90 deg,lr,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,90 deg,lr,cs,int epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,90 deg,lr,cs,int epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,90 deg,lr,cs,int epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,90 deg,lr,cs,int epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,90 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,90 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45deg,lr,cs (in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45deg,lr,cs (in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45deg,lr,cs (in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45deg,lr,cs (in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45deg,lr,cs(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,45deg,lr,cs(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,45deg,lr,cs(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , elb,45 deg,lr,cs,ext epoxy ctd, b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for external coating requirements, refer doc. 6745-pip-000-ec-0022 , con red,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for higher size , con red,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for higher size , tee,cs(in+ex epoxy), b16.9, bw ends,sch std, seamless, external epoxy coated, internal epoxy coated, a234 gr.wpb-s, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022, 4.schedule indicated is for run size , tee,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022, 4.schedule indicated is for run size , tee,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022, 4.schedule indicated is for run size , tee,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for run size , tee,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for run size , tee,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for run size , ecc red,cs(in+ex epoxy), b16.9, bw ends,sch std, seamless, external epoxy coated, internal epoxy coated, a234 gr.wpb-s, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022, 4.schedule indicated is for higher size , ecc red,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022, 4.schedule indicated is for higher size , ecc red,cs(in+ex epoxy), b16.9, bw ends,sch std, lw,100% radiography, external epoxy coated, internal epoxy coated, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.for external coating requirements, refer doc. 6745-pip-000-ec-0022, 4.schedule indicated is for higher size , ecc red,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for higher size , ecc red,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for higher size , ecc red,cs,(int epoxy ctd), b16.9, bw ends,sch std, lw,100% radiography, internal epoxy coated, weld factor e = 1.00, a234 gr.wpb-w, add. information, 1.for general technical requirements, refer doc. 6745-pip-000-ec-0001, 2.for internal coating requirements, refer doc. 6745-pip-000-ec-0023, 3.schedule indicated is for higher size => limited