tender for termite treatment work in house number-a-1006 type-5 house located in la place colony, replacement of damaged doors of the house along with frames, removal of damaged duct window and aluminium work, aluminium partition in both bedrooms of the house and other necessary repair work. 1 dismantling doors,windows and clerestory window (steel or wood) shutter including chowkhats,architrave,holdfast etc.complete and stacking within 50 meters lead:of area 3sqm and below.(15.12.1). 2 providing & injecting chemical for post constructional anti termite treatment with drill holes and junctions of floor with walls and pillars. the application of chemicals shall be as per relevant i.s codes and rate of application of chemical shall be also providing in the i.s code including quarterly inspection and providing required treatment for one year as per direction of engineer-in-charge. 3 salwood chaukhat 120x65 single rebate i/c joint treated with fevicol properly nailed with one coat of primer ,black japan paint on wall side e/c cost of hold fast complete 120x65 mm double rebate(tolerance 3mm).sl. no.-19. 4 providing and fixing isi marked 35 mm thick flush door shutters conforming to is : 2202 (part i)non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply veneening with vertical graints or cross brand and face veneers on both faces of shutters. dar n0-9.21.1 5 providing and fixing 1st quality ceramic glazed walls tiles conferming to is:15622 (thickness to be specified by the manufacturer ) of approved make, in all colours shades except burgundy , bottel green , black of any size as approved by engineer -in -charge , in skirting risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete(size-300x450mm) (dar-8.31) 6 providing and laying rectifited glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with grey cement slurry @3.3kg/sqm including grouting the joints with white cement and matching pigment etc.,complete. (dar-11.40) 7 providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections of approved make conforming to is 733 and is 1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required epdm rubber/neoprene gasket etc.aluminum sections shall be smooth, rust free straight mitred and jointed mechanically wherver required including cleat angle, aluminium snap beading for glazing/paneling c.p. brass/stainless steel screws, all complete as per architectural drawings and the directions of enginner-in-charge (glazing paneling and dash fasteners to be paid for separately). powder coated aluminium (minimum thickness of powder coating 50 micron). (dar no- 21.1.2.2) 8 providing and fixing of glazing in aluminium door/ window, ventilator shutter and partitions etc. with epdm rubber/ neoprene gasket etc. complete as per the architectural drawings and the direction of engineer-in-charge. (cost of aluminium snap beading shall be paid in basic item). with float glass panes of 5 mm thickness. (weight not less than 12.50 kg/sqm) dar-21.3.2,(rs-903) 9 supply and fixing alluminium window fitting as sliding bolt, tower bolt, handle, stopperetc complete as per direction fo engineer in charge.(based on actual requirment ). 10 filling the gap in between allmunium frame and adjacent rcc/brick/stone work by providing weather/structural non sag elastomeric pu sealant over backer rod of approved quality as per architectural drawings and direction of engineer-in-charge complete complying to astm c920, din 18540-f & iso 11600. upto 10mm depth and 10mm width item no 21.19.2