tender for repair of dampness in bathroom and bedroom damaged due to dampness in house number f-207 type-4 located in gomti nagar phase-2 ministers residence, work of replacing damaged window and door frames, work of installing grill and mesh in balcony and other necessary repair work. 1 dismantling tiles work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. for thickness of tiles 10 mm to 25mm. dar 15.23.1 2 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to is: 15622 of approved make in colours white, lovry greyfume red brown laid on 20 mm thick cement mortar 1:4 (1 cement :4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc complete. 11.39 3 providing and fixing 1st quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer) of approved make in all colours shades except burgundy bottle green black of any size as approved bye/i in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed pigment of matching shade complete. 8.31 4 structual steel work riveted bolted or welded in built up section, trusses, builds up gates,framed work lncluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. sl.n0-10.2, 5 providing and fixing isi marked 35 mm thick flush door shutters conforming to is : 2202 (part i)non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply veneening with vertical graints or cross brand and face veneers on both faces of shutters. dar n0-9.21.1 6 providing and fixing of 35, mm thick up teak wood jali door and window shutter withheavy quality s.s. jali with necessary beading, including supply and fixing of wooden cleats and stopper and including fixing and adjustment of hinges, bolts, locks handles, spring & or otherfitting but excluding their supply etc. painting two coats of black japan on all frame fitting in necessary etc. complete work as per direction of e/i. 7 renewing glass panes, with putty and nails wherever necessary including racking out the old putty: float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) dar 14.5.2 8 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge. (glazing, paneling and dash fasteners to be paid for separately) : power coated aluminium (minimum thickness of power coating 50 micron) dar-21.1.2.2, 9 providing and fixing of glazing in aluminium door/window, ventilator shutter and partitions etc, with epdm rubber/ neoprene gasket etc, complete as per the architectural drawings and the direction fo e/i (cost of aluminium snap beading shall be paid in basic item with apc sheet (aluminium power coated sheet). 10 providing & fixing float glass panes 5.00 mm thick glass panes (weigh not less than 12.50 kg/sqm)(dar -9.7.7.2)