different kind or repairing work at municipal area. dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including t&p and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 50 metres as directed by engineer. rubble stone masonry in cement mortar 2 cement concrete grade m-15 and above and pcc blocks 3 carriage of materials by mechanical transport including loading, unloading and stacking 1 km lead. 4 providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 5 steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.in gratings, frames, guard bar, ladder, railings, brackets, gates andsimilar works. 6 providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). 7 cement plastering including t&p, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement : 4 fine/ coarse sand) 8 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. red sand stone 9 brick masonry work with first class fps bricks (min. 10.5 mpa) in cement mortar with mechanical mixer in substructure/ super structure at all levels complete as per clause 1300 and 2200 of mort&h specification including all material, labour, scaffolding etc but excluding pointing and plastering.in cement mortar 1:4 (1 cement : 4 coarse sand). 10 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigmentto match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 11 providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or r.c.c. battens (karries and battens to be paid separately) including pointing the ceiling joints with cement mortar 1:3 red sand stone slab 12 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 13 finishing walls with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications :two or more coats applied @ 1.25 ltr/10 sqm. over and including one coat of special primer applied @ 0.75 ltr / 10 sqm. 14 providing and fixing water closet squatting pan (indian type w.c. pan ) with 100mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors whereverrequired : white vitreous china orissa pattern w.c. pan of size 580x440mm with integral type foot rests. 15 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively. 16 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required pvc/neoprene felt etc. aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing and panelling to be paid for separately) : for fixed portion. powder coated aluminium (minimum thickness of powder coating 50 micron) 17 providing and fixing 12mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with c.p. brass / stainlesssteel screws etc. complete as per architectural drawings and directions of engineer-in-charge.pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. 18 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with pvc/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (cost of aluminium snap beading shall be paid in basic item) : with float glass panes of 4.0 mm thickness. 19 removing & re-fixing of precast cement concrete interlocking paving blocks of all sizes over 50 mm thick course sand bedding (duly compacted) including filling of joints with sand complete in all respect. 20 providing and fixing of precast concrete interlocking tiles of desired shape of m 30 grade manufactured from fully computerized automatic stationery hydraulic viebro pressed machine and fully computerized automatic batching plant of class a1/a2 as per bs 6717:2001. the cc interlocking paving blocks be laid on average 50mm. thick bed of coarse sand and the joint is to be filled with fine sand. laying procedure on compacted sub-base as defined. complete job is to be executed as per the instruction of engineer incharge. the rates to be inclusive of all lead & lifts etc. complete as per specifications. tensile splitting strength, abrasion and brakingload etc. as per bs 6717:2001, grey cement.80mm thick