supply of modular office work station , cabin table: supplying and fixing standard cabin table of i. main table size - 1500mm ( w ) x 750mm ( d ) x 750 ( h ) ii. worktop will be in single piece made up of prelaminated particle board. iii. the worktop shall be made of 25mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding . iv. the worktops shall be provided with mettalic inserts for precise alignments and longer life v. the side panels are also made up of 25mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding . vi. modesty of the table is made up of 18 mm thk. interior grade-i conforming to is 12823 prelamianted particle board with 2 mm thick hot melt pvc edge banding .vii. key board tray; metal keyboard tray with mouse padto be considered. the key board drawer should move on telescopic channels for smooth operation and shall be fixedbelow the table for smooth movement. , side unit: i. side unit - length , depthand height of storage to be varies as per site measurment.so volum of storage to be measured in cum ii. side unit top shall be made of 25mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding .iii. side unit should have two drawer on top with sliding shutter credenza under it. iv. the worktops shall be provided with mettalic inserts for precise alignments and longer life v. sides of the side unit shall be made of 18mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding .vi. drawer facia and sliding shutter of the unit shall be made of 18mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding . vii. back of the side unit shall be made of 9mm thick interior grade-i conforming to is 12823 prelaminated particle board. viii. complete hardwares to be used from ebco , backstorage unit: i. back unit : length , depthand height of storage to be varies as per site measurment.so volum of storage to be measured in cum ii. back unit top shall be made of 25mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding .iii. back unit should have sliding shutter unit. iv. the worktops shall be provided with mettalic inserts for precise alignments and longer life v. sides of the back unit shall be made of 18mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding.vi. sliding shutter of the unit shall be made of 18mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding . vii. back of the back unit shall be made of 9mm thick interior grade-i conforming to is 12823 prelaminated particle board. viii. complete hardwares to be used from ebco , medium height storage: i. medium height stoarge : 900mm ( w ) x 450mm ( d ) x 1200 ( h ) ii. storage unittop shall be made of 25mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding .iii. storage unit should have hinge shutter unit. iv. the worktops shall be provided with mettalic inserts for precise alignments and longer life v. sides of the storage unit shall be made of 18mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding.vi. hinge shutter of the unit shall be made of 18mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding . vii. back of the stoarge unit shall be made of 9mm thick interior grade-i conforming to is 12823 prelaminated particle board. viii. complete hardwares to be used from ebco , work stationtable: supplying and fixing standard work stationtable i.worktop will be in single piece made up of prelaminated particle board. ii. the worktop shall be made of 25mm thick interior grade-i conforming to is 12823 prelaminated particle board with 2 mm thick hot melt pvc edge banding . iii. the worktops shall be provided with mettalic inserts for precise alignments and longer life iv. the work top shall be fixed in side panel based partition v. key board tray; metal keyboard tray with mouse padto be considered. the key board drawer should move on telescopic channels for smooth operation and shall be fixedbelow the table for smooth movement. vi. the length & width of table top to varies as per site measurement .so the area of table tobe measured in sqm. , panel based partition : panel based partition of 60mm thickness with framework made up of aluminium alloy extrusions. all aluminium parts are pretreated for epoxy polyester powder coated of 40-60micron thickness. all these frame work sections are fitted to each other by screws which is properly zinc coated for corrosion resistant. one single frame consists of following components :- 1.vertical member in aluminum alloy extrusion ( thickness 1.6mm ) . 2. top horizontal member in aluminum alloy extrusion of size 60x30mm ( thickness 1.3mm ) . 3. mid member in aluminum alloy extrusion of size 60x22mm ( thickness 1.3mm ) having provision to support the worktop with engineered design support bracket. 4. bottom raceway in aluminum alloy extrusion of size 140mm ht. x 60mm ( thickness 1.2mm ) . 5. intermediate raceway in aluminum of size 140mm ht above / below the work top as per requirement. 6. tiles as per spec 7. top and end trims as per spec 8. connectors as per spec 9. wire management as per spec , cpu trolley : the unit shall be of 240mm high with adjustable width from 220 to 320mm made of minimum 2.0mm thick crca steel sheet grade a as per is 513 duly epoxy powder coated of minimum 50 micron thickness having high density @ 70-75 kg / cum cross linked polyethylene foam spacers of 8mm thick and 2 nos. lockable castors & 2 nos. non lockable castors. , pedestal : 400 ( w ) x 450 ( d ) x 680 ( h ) top drawer should have a stationary tray made of 18mm thick pre-laminated particle board of interior grade-i conforming to is 12823 having three drawer configuration, two for personal and one for lateral files. the drawer of pedestal shall be made of particle board finished with laminate of approved colour shade and pattern. the drawer shall be fitted with full extension, ball bearing slides and handles of approved make and quality. all drawers to be lockable with single key system. the pedestal shall be provided with required number of castors. , work station chair the medium back adjustable revolving chair made with mesh back within built handle in the nylon finish, the back is designed extra lumber support. the seat have provided seat cover in pp made with 12mm hot pressed ply and pu moylded foam. the tilting mechanism should be synchro-tilt mechanism as per international ergonomics standards any position locking. the base and pin wheels are made in the nylon. 120mm h gas lift should be provided with tower bellow , high backchair high back chair made with feather foam seat & mesh back with lumber support. , the gas lift mechanism should be tested as per bifma x 05.01.2002 standards. the pedestal should be five legged injection moulded in black 30% glass –filled nylon and fitted with 5 nos twin wheel castors. the castors of the chairs should be glass filled, it should have synchro any angle locking arrangement , visitors chair 1. the seat and back should be made up of 1.2 ±0.1cm thick hot-pressed plywood measured as per qa method described in ocp-qlta-p14-18 and upholstered with fabric upholstery covers and moulded polyurethane foam. 2. the back foam should be designed with contoured lumbar support for extra comfort. 3. the seat should be extra thick foam on front edge to give comfort to popliteal area. 4. the dimensions of back should be 47 cm ( w ) x 47.0 cm ( h ) and of seat should be47.0 cm ( w ) x 43.0 cm ( d- lumbar point to seat edge ) . 5. the high resilience polyurethane foam should be moulded with density not less than 45kg / m3. 6. the one-piece armrests should be injection moulded from black polypropylene. 7. overall dimensions ( approx ) of chair should be seat height - 46cm, height - 89cm, width & depth of chair as measured from pedestal - width-61 cm and depth-64 cm