tender for remaining work for construction of vardhaman sabhamadap at jain prakrit deptt. mlsu - 1 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 2 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level.1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size). 3 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1-cement : 6-sand). 4 r.r dry stone kharanja under floor 5 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 6 (1 cement : 6 coarse sand) 6 providing and fixing fully panelled/partly panelled/ double leaf shutter frames for doors as per approved design anddrawings with approved ordinary c.p./ oxidised steel fittings as per annexure - a and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm x 12mm on both faces complete :..35 mm thick .ivory coast wood grade i 7 providing and laying brick kharanja on roofs with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound in square pattern 8 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :) 9 plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish :2smm thick. 10 providing and applying white cement based putty over plastered surface to prepare the surface even and smoothcomplete new plastered surface (three or more coats) 11 finishing with neat cement (punning) 12 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision new work 13 providing and laying damp-proof course with cement concrete grade m-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification .75mm thick. 14 french sprit polishing two or more coats on new work including a coat of wood filler. 15 chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cementmortar 1:4 (1 cement : 4 coarse sand)dark shade using ordinary cement. 16 providing and laying in position cement concrete including curing compaction etc . completein specified grade excluding the cost of centering and shuttering. all work up to plinth level using crusher broken aggregate m10 grade nominal mix ( with graded stone aggregate 20mm nominal size) 17 providing & fixing door, window, chowkhats and other frames, including antitermite treatment, m.s. flat, hold fasts of size 250 x 40 x 3mm fixed with m.s. bolt 5mm dia 50mm long duly embedded in cement concrete m-15 grade :sal wood grade - i 18 providing and fixing aluminum work for doors ,windows,ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and the directions of engineer- in – charge .(glazing and paneling tobe paid for separately).for fixed portion anodised aluminum (anodised transparent 81 dyed to required shade according to is : 1868. (minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer) 19 ….do…...for shutters of sliding windows and making provision for fixing of fittings wherever required (lockes shall be paid for separately) 20 providing and fixing glazing in aluminium door, window, ventilator shutter and partition etc with pvc/neoprene gasket etc complete as per the architectural drawings and the direction of engineer in charge ( cost of aluminium snap beading shall be paid in basic item) with glass panes of 5.0 mm thickness (weight not less then 13.75 kg/sqm) as per is:2835 21 add extra for providing and fixing expanded grill made of anodised aluminium as per design and drawing having members section of7.5 mm x 6.0 mm and opening of size 50 mm x 50 mm to aluminum window/vent with required screws. y and h aluminum sec ( as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer-in-charge. 22 s&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by aluminium beading 20x3 mm with suitable screwsat not exceeding 150mm distance at all height with all lead and lift with scaffolding 23 p/f rigid pvc pipe (is:4985 mark) class ii (4 kg./cm2) approved quality/make incl. jointing the pipe with solvent cement rubber ring and lubricant 110 mm dia. 24 p/f rigid pvc pipe fittings (is:4985 mark) of approved quality/make incl. jointing the pipe with solvent cement rubber ring and lubricant door tee 110 mm 25 ---do--- bend 87.5, 110mm dia. 26 (--do—) pipe clip 110mm