tender for annual plan-90 facilitation centre feeding room-changanassery-general civil work--- 1 facilation centre 2 21.13:providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete 3 21.17:providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to is : 1868 with minimum anodic coating of grade ac 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with c.p brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of engineer-in-charge.(only weight of grill to be measured for payment ). 4 21.3.1:providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in -charge. ( cost of aluminium snap beading shall be paid in basic item):with float glass panes of 4.0 mm thickness 5 21.1.1.1:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionanodised aluminium (anodised transparent or dyed to required shade according to is : 1868, minimum anodic coating of grade ac 15) 6 21.1.1.2:providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is : 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminnium snap beading for glazing /paneling, c.p. brass/ stainless steel screws, all complete as per architectural drawings and the directions of engineer-in-charge.(glazing, paneling and dash fasteners to be paid for separately):for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 7 22.2.1:providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed withwater proofing compound conforming to is : 2645 in recommended proportion with a gap of 20mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by engineer-in-charge:using rough kota stone 8 13.43.1:applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:water thinnable cement primer 9 13.60.1:wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:two or more coats on new work 10 11.36:providing and fixing i st quality ceramic glazed wall tiles conforming to is : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer -in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 11 21.2.2:providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is : 12823 grade i type ii, in panelling fixed in aluminum doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer - in- charge.pre- laminated particle board with decorative lamination on both sides 12 9.97.5:providing and fixing aluminium tower bolts, isi marked, anodised(anodic coating not less than grade ac 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:100x10 mm 13 9.113:providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of engineer- in- charge. 14 9.100.1:providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm