|
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 3 m above ground level and whereever required and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared including all labour, materials , tools, equipments etc., all complete and as directed by kpl |
| 2 | Felling trees of the girth 20 Cm to 60 Cm and above (measured at a height of 1 m above ground level), including cutting of trunks and branches and removing the all cut pieces and leaves are dumping the same nearby for disposal etc.,including all labour, materials ,equipments ,tools etc., all complete and as directed by kpl |
| 3 | Demolishing brick work In cement mortar including stacking of serviceable material and disposal of unserviceable material within 50m lead including all labour, materials ,tools etc., all complete and as directed by kpl |
| 4 | Dismantling gypsum partitions/Thermo coal false ceiling including framework (Aluminium/steel), and false ceiling including handing over the serviceable material to dept store and disposal of unserviceable material within 50m leadincluding all labour, materials ,tools etc., all complete and as directed by kpl |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.- All kinds of soil - as directed includind dressing…etc complete and as directed by kpl |
| 6 | Excavating, supplying, stacking , Transporting and filling of local earth by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift and as directed by kpl |
| 7 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12 mm diameter holes and with Chlorpyriphos/Lindane E.C. 20% with 1% concentration including all materials, cement, labour, tools, plants, equipments, etc., complete and as directed by kpl |
| 8 | Providing and laying plain cement concrete of mix 1:4:8 (1Cement: 4 fine aggregate : 8 hard granite graded stone aggregate of 40mm nominal size) in volumetric proportions for flooring to a required thickness and wherever required all as per relevant specification and as directed at site including shuttering, mixing, transporting, vibrating, placing, ramming, consolidating, curing etc., including all materials, cement, labour, tools, plants, equipments, etc., complete and as directed by kpl |
| 9 | Providing and laying plain cement concrete of mix1:1.5:3(1Cement:1.5 fine aggregate : 3 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions to a required thickness and wherever required all as per relevant specification and as directed at site including shuttering, mixing, transporting, vibrating, placing, ramming, consolidating, curing etc., including all materials,cement, labour,tools,plants,equipments, etc., complete and as directed by kpl |
| 10 | Providing Steel reinforcement for all R.C.C. works including straightening, cutting,bending, placing in position and binding all complete by using Thermo-Mechanically Treated bars of grade Fe-500D including all labour, materials, tools, equipment, transporation, binding wire etc., complete.and as directed by kpl |
| 11 | Brick work with common burnt clay (non modular) bricks of class designation 5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 fine aggregate) Whereever required including all labour, materials, tools, equipment, transporation, etc., complete and as directed by kpl |
| 12 | Plastering work in C.M 1:4(1 cement: 4 coarse sand) for internal wall area with 12mm thickness wherever required including all labour, materials, tools, equipment, etc.,complete and as directed by kpl |
| 13 | Plastering work in C.M 1:6(1 cement: 6 coarse sand) for External wall area with 15mm thickness wherever required including all labour, materials, tools, equipment, etc.,complete and as directed by kpl |
| 14 | Chiping the existing damaged and preparation of surface for existing walls portion wherever required in CM 1:4 and the prepare the Surface for plastering including all labour, materials, tools, equipment, etc.,complete and as directed by kpl |
| 15 | EPOXY Water Proofing Treatment in Terrace: Providing and laying integralEpoxy based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (i) Removing /dirt, oil and other contaminanats, loose materials with wire brush on the terrace and other surfaces (ii) Mix LAPOX LACRETE in ratio 1:0.5 and applying uniformly in thin layer on preapred substrate surfaces as primer coat and allow air cure for 4 hours.(iii) Laying of 150 Gsm fibre glass mesh over the first coating and apply second coat with same Laplox lacrete mix . (iv ) Mix LALOX PU Top coat in ratio 4:1 and applying pre coats with roller and allow for 24 hours for air cure (v ) Applying second coat with same LALOX PU mix as second and top coat with minimum of 200 microns thick for two coats and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabsand as directed by kpl including all labour, materials ,tools etc., all complete (vi) The whole terrace so finished shall be flooded with water for a minimum period of seven days for final test and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 16 | Grouting and water proofing wherever required and as per direction of kpl …etc complete a) Identifying the week areas on the surafce, joints, crack set and drilling holes of 10mm dia, fixing PVC nozzle with polymer mortar in the drilled holes. b) Water proofing in Terrace- Cleaning the surface area with wire brush and water wash apply the brushbond roof guard is high build fibre reinforced seamless waterproofing render suitable for waterproofing of old and new roofs, it is a polymer base product applied in terrace surface area with two coats. c) he Identified Area is Clean and Free of Dust and other particles, etc,. Reinforcing steel must be primed with Nitozinc Primer immediately after cleaning. All surfaces including edges must be primed and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 17 | Grouting the joints of flooring tiles having joints of 3mm width using epoxy grout mix of 0.70kg organic coated filler of desired shade including filling /grouting and finishing complete as per direction of Engineer In Charge and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 18 | Surface Preparation by Scrapping , cleaning thoroughly the existing wall surfaces to the required thick wherever necessary without damaging the wall and making suitable for painting and colour washing including collecting and bringing the debris to the ground level and depositing within a lead of 50m for disposal, all as per relevant specification and as directed at site and including all labour, tools, equipments, transport, fuel, etc., complete and as directed by kpl |
| 19 | Supplying and Laying 18mm - 22mm thick mirror polished machine cut granite stone for “Inauguration stone”, engraving letters & images in the inauguration stone as required and fixing on the wall or wherever required and painting with enamel paint of golden colour or shade as approved by KPL in the engraved letter & image portions including all labour, materials, tools, transportation, loading, unloading etc., complete. |
| 20 | Providing and laying flamed finish granite stone flooring 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including curing and polishing etc all complete as specified and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 21 | Providing and applying Wall Putty 2mm thick over a prepared inner wall surface and making the surface smooth and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 22 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content with water thinnable cement primer on wall surface having VOC content less than 50 grams/litre and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 23 | Applying Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.(Two coats) and where ever required and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 24 | Applying two coat of Exterior paint (Asian ace) paint for outer wall area for New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) of approved brand and manufacture, including applying additional coats wherever required, to achieve even shadeand including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 25 | Painting exterior surface with TEXTURED exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: On new work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm where ever required and as directed by kpl including all labour, materials ,tools etc., all complete |
| 26 | Applying synthetic enamel paint 2 coat of approved brand for wood/steel surfaces of required colour and scarapping througly including cost of material , labour, transport , tools etc. complete as directed by KPL |
| 27 | Applying Coal Tar Epoxy/Epoxy Paint(two or more coats) painting at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat including preparation of of old/new steel surface etc.... including cost of material , labour, transport , tools etc. complete as directed by KPL |
| 28 | Supplying and painting old/New wood work with grey primer of approved brand including surface preparation and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 29 | Providing and fixing in position first class country wood (Padauk) wrought main frame for door frame with necessary M.S. hold fasts/clamps fixed suitably to the masondry/concrete including cutting pockets and grouting graded stone aggregate of 20mm nominal size) in volumetric proporations,curing including painting with one coat of bolling coal tar paint on the portions of the timber abutting against mason dry/ concrete all as shown in the drawing and as dorected including cement and all other materials,labour,tools etc.. complete and as directed by KPL |
| 30 | Providing and fixing in position of flush Door shutters conforming to IS :2202 (Part 1) non-deconrative type , core of block board construction with frame of 1 st class hard wood and well mached commerical 3 ply vaneering with vertical grains or cross bands and face veneers on both faces of shutters and as directed by Kpl including all labour, materials tools etc.. all complete 35 mm thk including ISI marked stainless steel butt hinges with necessary screws (single leaf) and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 31 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of kpl . (M.S hold fast/lugs or SS dash fasteners shall be paid for separately) - Frame size 50 x 100 mm and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 32 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of kpl (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) - 30 mm thick and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 33 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Kpl. - PARITION & DOORS and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 34 | Providing and fixing bright finished SS 100mm mortice latch and lock with one dead bolt and a pair handles of size 125mm approved quality with necessary screws and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 35 | Supplying and fixing anodised aluminium (AC 10 grade) fittings for doors, windows etc., with necessary screws all as per relevant specification drawings and as directed including all materials, labour, tools, equipments etc., complete as directed by KPL |
| 36 | Butt hinges 150 mm long with nylon washer |
| 37 | Draw bolt 250mm long |
| 38 | Tower bolt 150mm long |
| 39 | Aldrop 250mm long |
| 40 | D type Handle -100mm long |
| 41 | Providing and fixing Door Stoper including all materials, labour, tools, equipments etc., complete and as directed by KPL |
| 42 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc., and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 43 | Providing and Applying weather/ Strutural non sag elastomeric PU sealant (600ml Sausage) for joints in RCC/Brick/stone/wood/ceramic/Gypsum Aluminium work Complying to ASTM C920 DIN 18540-F&ISO11600…and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 44 | Supplying and fixing perforated mineral fibre false ceiling tiles of size 595mm x 595mm for replacing the wornout tiles in the exsiitng false ceiling areas and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 45 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the Kpl with 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 sqm )and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 46 | Providing and fixing Heat Resistant Terrace Tiles (300mm x 300mm in suitable thickness cement sand morter in 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio 1:1 including rubbing and polishing of he surface upto 3 cuts complete , including providing skirting upto 150mm height along the parapet walls including all labour, materials , tools , equipment etc., complete as directed by KPL |
| 47 | Design, Engineering, Supply, fabrication, transporting, assembling & erecting of MS Structural Members by cutting, welding, with Bolts & Nuts etc. in position as directed at the site, including cutting, hoisting, fixing in position by welding/bolting/riveting etc., for sheds and wherever required all as as directed including all labour, materials, tools, equipments, tackles, scaffolding etc., complete.Note: The Cost is exclusive of Primer and Paint, which will be shall be measured and paid separately under relevant item of this schedule and as directed by the Kpl |
| 48 | Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by kpl. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as directed by the Kpl including all labour, material, tools, scaffolding, etc. Complete. |
| 49 | Providing and fixing of Roller Blinds made of 38mmx38mm aluminium extruded top rail with powder coated finished enabled with control Mechanism to be louvolite and chain must be metal. Stops to be fitted top & bottom to eliminate over-run and it should have straight edge finish. The blinds should be of approved manufactures and complete as per the approved shade and texture.( Basic cost Rs 200/-)and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 50 | Sun control film : Removing, cleaning of existing Sun control film & Supplying, fixing Sun Control film Night vision 15 with 75% solar energy reduction of approved quality having size 3.8 micron thickness and fixing over plain glass in the Aluminium Window including cost of labour, material, equipments, machinery, , etc.,. complete Make . - 3M Make (or) Equivalent and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 51 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc and including all labour, tools,equipments, transport, fuel, etc., complete and as directed by kpl |
| 52 | 20mm Nominal dia pipe |
| 53 | 25mm Nominal dia pipe |
| 54 | 32mm Nominal dia pipe |
| 55 | 40mm Nominal dia pipe |
| 56 | 50mm Nominal dia pipe |
| 57 | 110mm Nominal dia pipe |
| 58 | Providing and fixing CP Health Faucet with hose and other required accessories to complete in all aspects and as direction of the kpl including all materials, labour, tools etc. |
| 59 | Providing and fixing PVC Health Faucet with hose and other required accessories to complete in all aspects and as direction of the kpl including all materials, labour, tools etc. |
| 60 | Providing and fixing PVC Tap and other required accessories to complete in all aspects and as direction of the kpl including all materials, labour, tools etc. |
| 61 | Providing and fixing CP Brass Bib Cock in the toilet all as per manufacture,s specification and as direction of the kpl including all materials, labour, tools etc. |
| 62 | Providing and fixing good Quality of European type water closet (White) (parrywareware-or Hindware ) with P (OR) S Trap of Approved make and quantity with white low level flushing cristern of 10 liters capacity with 40mm dia flush pipe, plastic seat and cover fixing T.W. Plugs etc including all materials, labour, tools equipments etc...complete. |
| 63 | Providing and fixing good Quality of Indian type water closet (White) (parrywareware-or Hindware ) with P (OR) S Trap of Approved make and quantity with white Colour.. etc including all materials, labour, tools equipments etc...complete. |
| 64 | Providing and fixing of Ceramic Urinal divider of size 350 x 675 x 130mm of Parryware Make or Equivalent to be fixed on to the existing urinal area in Gents toilet with all required Hardwares and to complete in all aspects as directed by KPL |
| 65 | Providing and fixing Connection Hose including all materials, labour,tools,equipments etc… complete. As directed by KPL |
| 66 | Supplying and fixing on wall face mirror of size 600x450mm (approx) beveled edge mirror with plywood/ hard board back of approved Qty as directed at site of work including all materials, labour, tools, equipments etc complete. As directed by KPL |
| 67 | Providing and fixing good Quality Wash Basin with C.L. Brackets 15mm dia CP Brass single hole basin mixer of approved quality and make including painding of fittings and brackets cutting and making good walls wherever required. wash basin size 550x400 mm with a 15mm CP Brass ssingle hole basin mixer as directed by KPL |
| 68 | Providing and fixing Approved quality CP Brass Angle cock in the toilet all as per manufacture,s specification and as direction of the kpl including all materials, labour, tools etc. |
| 69 | Providing and fixing Approved quality pillar cock in the toilet all as per manufacture,s specification and as direction of the kpl including all materials, labour, tools etc. |
| 70 | Wall painting and lettering the various KPL Buildings inside and outsite port area as directed by KPL incluting all labours,materials, tools equipments, scaffoldings etc....complete. |
| 71 | Supplying and Fixing of Mica Sheet of require size 0.8/1mm Thick with suitable adhesive including finishing the joint in uniform and all necessary accessories.. Complete as directed by kpl |
| 72 | Providing and fixing good quality fabric curtain cloth for windows with curtain rods rackets, rings stitching, for smooth movement including all accessories etc. all as directed kpl including all materials, labour, tools, equipments, etc. complete. |
| 73 | Supplying and fixing Wooden Shutters for cupboards of different sizes with including fixing with necessary hinges, screws, all as directed at site, including all materials, labour, tools, equipments, transport, fuel,etc.,complete and directed by kpl |
| 74 | Supply and fixing Ceiling light of Wipro or Equipment Make including necessary cableling and power points and as directed as site etc.,, including materials, labour, tools, equipments, transport,etc.,complete and directed by kpl |
| 75 | Supplying and fixing good quality insects preventing aluminium mesh grade 304 as 0.24 dia to main frame of the windows ventilators etc. wherever required after removing the old damaged mesh including providing powder coated aluminium frame size 19.4 x10.00x 1.00mm (Vertical and Horizontal as required numbers ) on all the sides of the existing wooden frames including fixing aluminium frames 50x25mm size allaround the windows inwalls with necessary requred fittings of the screen all of approved quality and as directed by kpl at site including all labours, materials , fabrication, tools equipments etc., complete. |
| 76 | Supplying and fixing Hinges for kitchen cupboards of different sizes with including fixing with necessary screws, all as directed at site, including all materials, labour, tools, equipments, transport, fuel,etc.,complete and directed by kpl |
| 77 | Supplying and fixing soft close EWC seat cover wherever require , all as directed by site , including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 78 | Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion(where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (ifrequired) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made:Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)Note: For uPVC frame, sash and mullion extruded profiles minus 5%tolerance in dimension i.e. in depth & width of profile shall be acceptable and including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 79 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. BASIC COST OF TILE - Rs.750 including all materials, labour, tools,equipments, transport etc.,complete and directed by kpl |
| 80 | Providing and laying Ceramic glazed floor/Wall tiles of to required sizethickness to be specified by the manufacturer) approved make in colours laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.,complete including all materials, labour, tools,equipments, transport etc.,complete and directed by kpl |
| 81 | Supply and Fixing of Sintex Tank with Capacity - 1000 ltrs of 3 layers and Should be 100% UV stabilized, Made up of 100% virgin material, Threaded lid, Extra insert lid for protection from algae formation, ISI Marked. FDA Approved and including all materials, labour, tools, equipments, transport etc.,complete and directed by kpl |
| 82 | Supplying JCB machinery on hire basis for attending emergency works and as directed at site of work including operators, diesel, fright charges,fuel ,etc.., complete and directed by kpl |
| 83 | Loading, transporting, dumping and leveling the Surplus earth/debris etc., in the low lying areas nearer to the site of work upto lead 2 km all as per relevant specifications and as directed including all labour, transport, tools, equipments, fuel, etc., complete directed by kpl |
| 84 | Providing and fixing double scaffolding system (Cup and lock type) on the exterior side , up to seven story height made with 40mm dia. M.S.tube 1.5m centre to centre , horizontal & Vertical tubes joining with cup & lock system with M.S tubes, M.S tube challies, M.S clamps and M.S staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing in there after. The Scaffolding system shall be stiffened with bracings,runners connection with the building etc. wherever required for inspecion of work at required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Kpl. The elevational area of the Scaffolding shall be measured for payment purpose.The payment will be made once irrespective of duration of Scaffolding and including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 85 | Providing Engineering Supervision including by engaging technical manpower through out the project execution period. The Payment for this item will be paid based on the certification of attendance by KPL and as per the conditions stipulated in the Clause 9.4 of Section 2 of Tender Document in Man months |
| 86 | Removal of Existing calling bell and replace with new calling bell with switch all accessories as per manufacture,s specification and as direction of the Kpl including all materials, labour, tools etc. |
| 87 | Wiring in PVC Conduit Point with modular type switch wiring for light point/exhaust fan point with 1.5sq mm FRLS PVC Insulated multistrand copper conductor wires in External surface/Concealed PVC conduct with suitable GI box and earthing the point with 1.5sqmm FRLS PVC Insulated multistrand copper conductor wire etc... including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 88 | Wiring in PVC Conduit Point for main power point with 2.5sq mm FRLS PVC Insulated multistrand copper conductor wires in External surface/Concealed PVC conduct with suitable GI box and earthing the point with 1.5sqmm FRLS PVC Insulated multistrand copper conductor wire etc including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 89 | Supply and fixing modular switch Box with 3 nos switches and 3 nos socket of 5/6 Amps on the modular plate including connection modular plate with suitable GI box and earthing the point with 1.5sqmm FRLS PVC Insulated multistrand copper conductor wire including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 90 | Supply and fixing modular switch Box with 1 nos switches and 1 nos socket of 15/16 Amps on the modular plate including connection modular plate with suitable GI box and earthing the point with 1.5sqmm FRLS PVC Insulated multistrand copper conductor wire including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 91 | Supply and fixing 20 watts LED 4 Feet Tubelight including all other accessories including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 92 | Supply and installation of 16 Amps Distributor box with 2 Pole MCB (16 Amps) with required Outdoor Unit enclosed including all other accessories etc including all materials, labour, tools,transport etc.,complete and directed by kpl |
| 93 | Supplying and fixing of 400 mm Dia Pedestal mounted fan and as per technical specification and as per latest IS .and including all materials, labour, tools, equipments, transport etc.,complete and directed by kpl |
| 94 | Supplying and fixing of 300 mm Dia Heavy Duty Exhaust fan and as per technical specification and as per latest IS .and including all materials, labour, tools, equipments, transport etc.,complete and directed by kpl |
| 95 | Supplying and fixing of 400 mm Dia wall mounted fan and as per technical specification and as per latest IS .and including all materials, labour, tools, equipments, transport etc.,complete and directed by kpl |
| 96 | Supply and fixing of 5 HP Monobloc pump with bedding arragements for the pump for fixing with necessary Starter, fittings including required wiring with earthing pit as directed at site and as per technical specification and as per latest IS / IES and including all materials, labour, tools, equipments, transport etc.,complete and directed by kpl Please Enable Macros to View BoQ information |
