|
| 1 | Demolition of roof treatment including PCC padding, plastering and APP membrane etc complete treatement of any thickness and any position and removing the demolished material out of MoD land complete all as specified and as directed. |
| 2 | M&L for 40 mm average thick PCC 1:2:4 type B0 (using 12.5 mm grd stone agg) in floors/padding finishing the surface even and smooth with out using extra cement. |
| 3 | M&L for bitumen felt water proofing treatment using APP based polymeric membrane minimum weighting 3kg/sqm and minimum thickness 3mm reinforced with polyster non wove fabric (but not less than 150gms/sqm) laid over bitumen primer applied @ 0.30 Kg/sqm by forced application complete all as specified and as directed. Make : IWL Limited, STP, Torchstar Ltd |
| 4 | M&L for roof cool tiles of size 30cm x 30cm x 7-8mm thick over cement mortar including 15 mm thick screed bed in cement mortar 1:4 and filling the joints with joint filler chemical or epoxy complete all as specified and as directed. |
| 5 | Dismantling asbestos cement (corrugated or semi-corrugated etc) sheets in roof covering including ridges, hips, valleys and flashings etc complete all as specified and as directed. |
| 6 | Pre- painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 7 | M & L pre- painted galvalume aluminium zinc coating (AZ-150) GI based Plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutters, fixed with self tapping screw as specified. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for door gates, grills, purlins, rafter or truss complete all as specified. |
| 9 | M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240. |
| 10 | S&F MS Framed work such as grills gratings , door and cooler stand, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars confirming to Fe.290.Gde-E-165 |
| 11 | M&L Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed . |
| 12 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified. |
| 13 | S&F 605x605mm of grid GI frame work for seamless ceiling comprising of GI perimeter chennel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylone sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm susoended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with clips of 10.5mm fixed to the intermediate channel at 457mm centre to centre including Hangers 6mm dia GI (upto 1200mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flate 40X30mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified inluding Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions and applying two coats of distemper over 1mm thick wall care putty over ceiling board complete all as specified and as directed. |
| 14 | S&F in repair Hollow PVC Wall lining consisting of 5-10mm thick plain colour PVC sheet and including 5mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on wall to make PVC frame for fixing the PVC sheet inclusive of solvent cement complete all as specified and directed. |
| 15 | S&F in rapair White glazed fine clay sink size 700x450x250mm with bracket, sink coupling and waste pipe complete all as specified and directed. |
| 16 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed. |
| 17 | M&L for Non skid/ Mat finish Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:4 and includnig dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.complete all as specified and as directed. |
| 18 | M&L for Glazed ceramic coloured tiles of size 300x600x7mm thick as on vertical surfaces laid over and including 10mm thick rendering in cement mortar 1:3 complete all as specified and as directed. |
| 19 | M&L light shade double charged vitrified ceramic coloured tiles 10 mm thick (square/rectangular) area of each tile exceeding 0.42 but nexc 1.00 sqm , in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. |
| 20 | M&L light shade double charged vitrified ceramic coloured tiles 10 mm thick (square/rectangular) area of each tile exceeding 0.42 sqm but nexc 1.00 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 10 mm thick screed bed in cement mortar 1:3 complete all as specified and as directed. |
| 21 | Demolition of stone slabs/tiles of any description or thickness in floors/apron etc laid bedded and pointed in any mortar complete all as specified and as directed. |
| 22 | M&L for 16-18mm thick Granite work of Z black or Red Rubby type as approved (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed. |
| 23 | M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as specified and as directed. |
| 24 | Taking down chowkhats or frame with shutter (without taking off shutters from the frame) area n.exc. 1.50 Sqm each complete all as specified and as directed. |
| 25 | Taking down Chowkhats or frames with shutters (without taking off shutters from frame) area exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and as directed. |
| 26 | S&F Solid WPC frame of size 100mm x 65mm made out of solid PVC frame with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) |
| 27 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush shutter of 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), Calciam Carbonate and natural fibres (wood poder/rice husk/wheat husk) and toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 65 kg/cum and screw withdrawl strength of 1800 N (Face) and 900 N (Edge)/ minimum compressive strength 50N/Sqmm, modulus of elasticity 850 N/sqmm and resistance to spreade of flame of class 'A' category with property of being termite/borer proof/ water/ moisture proof and fire retardant and fixing including with SS butt hinghes of 100 size with necessary full body threaded star headed counter sunk SS Screws etc all as per direction Engr-in-Charge. |
| 28 | Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 29 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame(88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mmx57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 30 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 31 | S&F in repairs aluminum (extruded section body) Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed. |
| 32 | S&F 5.5 mm thick sheet glass, ordinary quality and glazing with rubber beading/oil putty/wooden beading in square not exceeding 0.5 square metre in each pane complete all as specified and as directed. |
| 33 | S&F 5.5 mm thick sheet glass, ordinary quality and glazing with rubber beading/oil putty/wooden beading in square exceeding 0.5 square metre in each pane complete all as specified and as directed. |
| 34 | S&F 100 mm long stainless steel Butt hinges, medium weight, cold rolled complete all as specified and as directed. |
| 35 | S&F 150 mm mortise lock with handle 6 lever locking mechanism with reversible latch exterior chrome finish suitable for right or left both type including fixing with wooden door shutters complete all as specified and directed. Make Godrej or equivalent |
| 36 | S&F 150 mm long Extruded brass handles, fabricated type polished complete all as specified and as directed. |
| 37 | S&F 150mm long SS barrel tower bolts with barrel of extruded section complete all as specified and as directed. |
| 38 | Demolition of brick work built in cement mortar including all quoins, asches, pillars etc in any position complete all as specified and as directed. |
| 39 | M&L for brick work with old size burnt clay sub class 'B' bricks built in CM 1:6 straight or curved on plan exc 6 m mean radius complete all as specified and directed. |
| 40 | Taking down cement plaster from brick wall etc incl racking out joints & hacking out for key and scrubbing down with water all as specified. |
| 41 | M&L for 15mm thick rendering in cement mortar (1:4) on other than fair faces of brick/ concrete surfaces finished the surface even and fair without using extra cement, using 200 ml water proofing liquid per bag of 50 Kgs cement (but excluding the cost of water proofing liquid). |
| 42 | M&L for 10mm thick rendering in cement mortar (1:6) on fair faces of brick/ concrete surfaces finishing the surface even and smooth without using extra cement. |
| 43 | M&L for rendering 5 mm thick in CM 1:3 over and including 10 mm thick in CM 1:4 dubbing coat on ceiling surfaces of concrete finishing the surface even & smooth (without using extra cement) |
| 44 | Supply only water proofing liquid Dr Fixit or equivalent as approved. |
| 45 | M&L for prepartion of new plastered surfaces of walls and applying two coats of Acrylic Smooth exterior emulsion paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified. |
| 46 | M&L for preparation of new plastered surface of wall and applying two coats of oil bound Distemper white or tinted over and including over 1mm thick wall care putty on wall complete all as specified and directed. |
| 47 | M&L for 1mm thick water proof wall care putty over newly plastered surface to prepare the surface even and smooth. |
| 48 | M&L for complete removal old decorative treatment and preparition of old decorative surface of wall and applying two coats of oil bound Distemper white or tinted over and including 1mm thick wall care putty on wall complete all as specified and directed. |
| 49 | M&L for complete removal of existing treatement from old decorative surfaces of walls by sender machine for rubbing the old surfaces of walls neatly and applying two coats of Acrylic Smooth exterior emulsion paint of required shade over and including 2mm thick water proof wall care putty : (Two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified. |
| 50 | M&L for preparation of new plastered surface of ceiling and applying three coats of white wash on ceiling surface complete all as specified and directed by Engineer-in-Charge. |
| 51 | M&L for preparation of old plastered surface of ceiling and applying two coats of white wash all as specified and directed by engineer in charge. |
| 52 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish off the premises complete all as directed |
| 53 | M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surface even and smooth using extra cement. |
| 54 | M&L for 25 mm (Average) thickness cement concrete type- B0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling course below tiles etc finishing cement concrete surface even and fair without using extra cement compete all as specified and as directed. |
| 55 | M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete as per direction of Engineer-in-charge |
| 56 | M&L non skid cermic ENDURA coloured tiles 7-8mm thick (square/rectangular) area of each exc 0.11 Sqm but nexc. 0.18 Sqm as in floors set and jointed in neat cement slurry & pointed with coloured cement to match the colour of tiles laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. |
| 57 | S&F in repair 110 mm bore PVC (SWR) class 'B' pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 58 | S&F in repair 75 mm bore PVC (SWR) class 'B' pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls complete all as specified and as directed. |
| 59 | S&F in repair 110 mm bore PVC (SWR) plain bends any radius complete all as specified and as directed. |
| 60 | S&F in repair 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed. |
| 61 | S&F in repair 75mm bore PVC (SWR ) vent cowl complete all as specified and as specified. |
| 62 | S&F in repair PVC floor trap plain 75 mm dia of outlet with grating including jointing with solvent cement complete all as specified and as directed. |
| 63 | S&F in repair curtain rod stainless steel chromium plated 20mm dia with bracket knobs including end cap complete all as specified and directed. |
| 64 | Taking up or down 15 mm bore steel tubings and connections and removed from site complete all as specified and as directed. |
| 65 | S&F steel water tubing 15 mm bore medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floor complete all as specified and as directed. |
| 66 | Taking up or down 20 mm bore steel tubings and connections and removed from site complete all as specified and as directed. |
| 67 | S&F steel water tubing 20 mm bore medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floor complete all as specified and as directed. |
| 68 | M&L for Cutting chases pinning in brick walls making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled conduit wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed |
| 69 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever bracketsand connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm including waste coupling and waste pipe complete all as specified and directed. |
| 70 | S&F in repair sink mixer with EXTENDED swinging spout 450mm long (wall mounted model )with connecting legs and wall flanges for 15mm bore dia iron pipe complete all as specified and as directed. Make Jaquar Cat Part No FLR-CHR-5309N/ Cera Cat Part No: F-100351 / Kohler Cat Part No 37315 IN-4-CP. |
| 71 | S&F in repair 25mm dia chromium plated SS tubular curtain rod cut to size and fixed in position including fixing and connected items such as brackets for double rod and stop roller end caps etc complete all as specified and approved. |
| 72 | S&F in repair stainless steel peg stay having 8 hooks fixed with wall or wooden door complete all as specified and as directed. |
| 73 | S&F 1000 liters capacity rotational moulded polyethylene water storage tank (Triple layers white in colour) (Cylindrical vertical with close top) hoisted and fixed in position with tank nipple and connections etc including dismantling existing old water storage tank complete all as specified. Make SINTEX (PURE)/ VECTUS (SMART)/ SUPREME (WHITE). |
| 74 | S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for 20mm bore dia of pipe and fixed (Minimum weight 210 gms each) Make: Prayag/Polytuff/Prima |
| 75 | S&F in repairs Gun matel, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed as specified. Make: Prayag/Polytuff/Prima |
| 76 | S&F in repair Bib cock taps long body chromium plated cast copper alloy with wall flange, screwed down, screwed for iron pipe of bore 15mm complete. Make Jaquar Cat Part No: KUP-CHR-35037/ Cera Cat Part No: F-1003151/ Kohler Cat Part No: K-16093IN-4-CP . |
| 77 | S&F in repairs chromium plated brass anglular stop cock with wall flange screwed both ends high pressure for 15 mm bore size iron pipe or ferrule complete. Make: Jaquar Cat Part No: KUP-CHR-350553PM/ Cera Cat Part No: F-1003201/ Kohler Cat Part No: K-80154IN-4AV-CP . |
| 78 | S&F in repair Wall Mixer head and hand arrangement combination pattern including Telephonic hand shower, flexible tube and hook connecting legs and wall flanges, crutch etc complete all as specified. Make Jaquar Cat Part No: LYR- 38145/ Cera Cat Part No: F-1003403/ Kohler Cat Part No: 98754IN-4-CP |
| 79 | S&F in repair chromium plated over head shower (200x200)mm of square shape with 600 mm long arm complete all as specified and directed. Make Jaquar / Cera / Kohler |
| 80 | S&F in repair elbow operated wash basin mixture height 85 mm without popup waste system with 450mm long braided hoses complete all as specified. Make: Jaquar /Cera /Kohler |
| 81 | S&F in repair single lever Extended wash basin mixture height 85 mm without popup waste system with 450mm long braided hoses complete all as specified. Make: Jaquar Cat part No KUP-CHR-35011BPM/Cera Cat Part No: F-1003451/ Kohler Cat Part No: K-33063IN-4ND-CP . |
| 82 | S&F in repair PVC cabinet with mirror, of size 350 mm x 450 mm, fixed to wall with screw all as specified and as directed. Make:- Prayag Cat No 551/Commander / Neelkamal / Polytuff |
| 83 | S&F in repair Soap dish, of CP brass body and rectangular in shape, fixed to plugs with chromium plated brass screws Make : Jaquar Cat part No AKP-CHR-35731P/Cera Cat Part No: F-5012116CH/ Kohler Cat Part No: K-25069IN-CP |
| 84 | S&F in repair towel rack of 600mm long with lower hangers of approved make complete all as specified and directed. Make: Jaquar Cat part No CPA-CHR-1181FH/Cera Cat Part No: F-5012101CH/ Kohler Cat Part No: K-25066IN-CP |
| 85 | S&F in repair tubular towel rail of brass Chromium plated 20mm dia, ‘D’ type 60cm long between flange complete all as specified and directed. Make: Jaquar Cat part No CPA-CHR-1111/Cera Cat Part No: F-5013104CH/ Kohler Cat Part No: K-25065IN-CP |
| 86 | S&F PVC connection 15mm size with brass nut of 600mm long. |
| 87 | S&F in repairs 600x600 mm looking mirror bevelled edge of selected quality glass mounted on commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washer of approved make complete. Make: Prayag or equivalent. |
| 88 | S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete. Make: Jaquar/ Cera/ Kohler |
| 89 | S&F in repair vitreous china table top wash hand basin, size 560x400x130mm including CP brass waste coupling fittings, complete all as specified and as directed. Make Jaquar/Kohler/Cera |
| 90 | S&F in repair Vitrreous china wash down water closet pedestral pan white, Plastic water closet seat, closed pattern with recessed bottom, and seat cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed. Make: Cera/Kohler/Jaquar |
| 91 | S&F in repair Vitreous china wash down water closet single piece with seamless flushing cistern square design duroplast slim seat cover, slow falling seat cover size(705x370x770)mm, S trap 300 mm and other connected accessories including connection to drain pipe etc complete all as specified and directed. Make:Cera Christina Cat No. S1013119/Jaquar Cat part No FNS-WHT-40751S220UFSM/ Kohler Cat Part No: K-17629IN-SM-0 |
| 92 | S&F in repair Hand jet health faucet 15 mm bore with all connected fittings complete all as specified and as directed. Make: Jaquar Cat part No ALD-CHR-565GA/ Cera Cat Part No: F-8030116AB/ Kohler Cat Part No: K-12927IN-CP |
| 93 | S&F in repair tolilet paper holder of stainless stell fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. Make: Jaquar Cat part No AKP-CHR-35753PS/ Cera Cat Part No: F-5007110/ Kohler Cat Part No: K-5633IN-CP |
| 94 | S&F in repair Corner glass shelf with SS bracket fixed to wall complete all as specified and as directed. Make: Jaquar Cat part No ACN-CHR-1173/ Cera Cat Part No: F-5005102/ Peryware Cat Part No: T 6010A1 |
| 95 | Dismantling wall and ceiling boards/ Kitchen cabinets/ cupboards (fiber, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed. |
| 96 | S&F in repair any size of bevelled edge looking mirror of selected quality glass mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washer complete as specified and as directed. |
| 97 | S&F in repair bottle trap for 32mm bore discharge pipe (half or full threated) of Stainless Steel having min water seal of 40mm complete all as specified and as directed. Make: Kohler/Jaquar/Marc |
| 98 | Demolition of reinforced cement Concrete in slab or chajjas supported on walls or beams etc n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 99 | M&L reinforced cement concrete type B-1 (1:2:4) using 20 mm graded stone as in slab supported on walls, beams and columns in floor, roof, beams and shelves etc for soak well/septic tank in running and manhole cover slab with plain fair faces and set in CM 1:4 condition complete all specified |
| 100 | M&L form work to soffits of suspended slabs such as roof slabs, landing and similar work n exc 200 mm thick, curved, plain in running condition complete all specified (rough finished surfaces) |
| 101 | S&F for MS deformed bar or TMT bars 10 mm dia and over in reinforcement cut to length bent to shape reqd incl crancking, bending, binding, hooking end etc and binding with MS annealed with MS binding wire not less than 0.9 mm dia including supply of binding wire all as specified |
| 102 | Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc. ) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, light fittings etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed.( Note: Credit for above items should be made as per credit Schedule separately) |
| 103 | Taking down carefully by submain wiring of any type complete and making good disturbed sufaces to match with the existing surfaces all as directed by Engineer-in-Charge. |
| 104 | Taking down old unserviceable existing SPN/TPN DBs / enclousers any size and type / any descriptions as iron sheet scrap including MCB any type / size and making good disturbed surface / wall as per existing complete all as specified and directed |
| 105 | M & L for Point wiring with 1.5 sqmm (nominal area) single core PVC insulated sheathed (FRLSH) cable, 1100 volts grade, multi-stranded copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20 mm dia med gd) and its all accessories complete concealed in wall and modular flush metal boxes with modular cover plates & frames for mounting modular switches, sockets, regulators etc. including earth wire of PVC insulated (FRLSH) copper conductor multistranded of 1.5 sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge, as described below in item no 106-110:- |
| 106 | (a) One light point controlled by one switch 5 amp. |
| 107 | (b) One wall/exhaust fan point controlled by one switch 5 amp. |
| 108 | (c) One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified. |
| 109 | (d) One 5 Amp 5 pin socket outlet point on independent board with other switches including earth wire as specified. |
| 110 | (e) One bell point controlled by one push button. |
| 111 | All as per item No.105 here-in-above but for 3 pin/ 5 pin, sockets outlet,15 amps with 4.0 sqmm PVC insulated & unsheathed (FRLSH), multi-stranded copper condutor cable, independent, Point wiring complete all as specified and as directed . |
| 112 | Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete. |
| 113 | Supply and Fixing Modular bell Push switch 6 Amps with indicator single pole one-way, 1 Module . |
| 114 | Supply and Fixing Modular switch 16 Amp single pole one way,1 Module all as specified. |
| 115 | Supply & Fixing Modular fan Regulator electronic step type complete all as specified. |
| 116 | Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps, combined 2 Module complete all as specified. |
| 117 | Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete. |
| 118 | S&F Ding Dong Calling Bell |
| 119 | S&F Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten |
| 120 | Supply and fix in repair ceiling rose surface bakelite 65mm x 50mm three terminals complete . |
| 121 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holderconnecting up with three core flexible copper conductor cable of suitable size. |
| 122 | Supply and fixing LED lamp, 9 watt, B-22 base complete. |
| 123 | S&F indoor decorative ultra slim surface/ wall mounted LED batten tube light fitting complete, 1x 20 watt with polycarbonate channel housing & integrated electronic driver, energy efficient, 140V-270 volts, co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with pvc insulated pvc sheathed twin core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. |
| 124 | S&F indoor decorative ultra slim surface/ wall mounted LED batten tube light fitting complete, 1x 10 watt with polycarbonate channel housing & integrated electronic driver, energy efficient, 140V-270 volts, co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with pvc insulated pvc sheathed twin core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. |
| 125 | Supply & fix in repair recess type, 35/36 watt LED panel light (600x600 mm) colour warm/white complete with fittings integrated electronic driver,energy efficient, 230 volts,co- related colour temperature (CCT) of 6500K, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete. |
| 126 | Supply and install of 35W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including all connections complete all as specified. |
| 127 | M&L for building security light bracket made out of 40mm dia light grade GI pipe |
| 128 | M & L for Sub Main Wiring for DB to DB with two runs single core 10 Sqmm PVC insulated unsheathed (FRLSH) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 10 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge.(02 run 10 Sq mm single core cable, one run of 10 Sq mm earth wire & One run of PVC conduit will measured as one RM). |
| 129 | All as per item No.27 here-in-above but for 6.0 sq. mm |
| 130 | All as per item No.27 here-in-above but for 4.0 sq. mm |
| 131 | Supply and fix Wall fan, complete with three blade of 400 mm sweep |
| 132 | Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor. |
| 133 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380mm sweep with, blades, and frame and louvers |
| 134 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm |
| 135 | Cutting holes for air ducting of exhaust fan in Circle / square shape or as per site |
| 136 | Single pole and neutral enclosure with a two pin and earth plug and socket complete with one Single pole MCB 20 amp |
| 137 | M&L vertical load line distribution board factory made and tested made of sheet metal enclosure powder coated suitable for MCCB 200A triple pole and neutral as incomer and outgoing MCBs, 12 way TPN with rated busbar 415 volts,neutral link, Blanking plates (Without MCCB/MCBs) IP 43 (double door type) ISI marked suitable for A Frame MCCB 200 Amp as incommer of Make: Havells Cat Pt No DHDLVDOBGSFE12 of Havells or its equivalents (Note MCCB Price should be measured and paid seperately) |
| 138 | Supply & fix in replacement of MCCB 200 Amps, breaking cap 25 KA, 4 Pole, 415V complete including taking down old MCBs all as specified and directed. |
| 139 | S&F MCB distribution board, SPN 12 way, double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail, cable ties for cable management, 240 V, complete all as specified. |
| 140 | S&F MCB distribution board, SPN 8 way, double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail, cable ties for cable management, 240 V, complete all as specified. |
| 141 | S&F MCB SPN, 32 Amps, 'C' series, breaking cap 10 kA, 240V in MCB DB complete with electrical connection all as specified and directed. |
| 142 | S&F MCB SPN, 40-63 Amps, 'C' series, breaking cap 10 kA, 240V in MCB DB complete with electrical connection all as specified and directed. |
| 143 | S&F MCB SP, 6-32 Amps, 'C' series, breaking cap 10 kA, 240V in MCB DB complete with electrical connection all as specified and directed. |
| 144 | S&F MCB SP, 40 Amps, breaking cap 10 kA, 240V in MCB DB complete with electrical connection all as specified and directed. |
| 145 | M&L for earthling complete with galvanized steel earth plate eletrode 60x60 cm x6.3 mm thick burred directly in ground (earth pit not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Metrs below normal ground level connected to galvanized earth lead wire 4.00mm dia by means of bolts, nuts check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 connected to earthling test point all as specified and indicated including testing on completion including excavation and arth work PCC pit & RCC pit over funnel with watering pipe wire mesh GI protection pipe etc complete. Please Enable Macros to View BoQ information |
