|
| 1 | M-150 Brick Work with cement and coarse sand in proportion of 1:4 in foundation and plinth including supply of all material labour. Tools & plants etc. required for proper completion of the work S.I no. 305 A and 310 |
| 2 | 12mm thick plaster with cement and fine sand 1:4 over brick work minimum thickness not to be less than lem. Including supply of all materials, labour, tools & plants etc. required for proper completion of the work as per site direction of engineer in charge (S.I - 584) |
| 3 | Providing and fixing in position collapsible steel shutters with vertical chaneels 20*10*2 mm and braces with flat form diagonals 20*5 mm size with top and bottm rails or T-iron 40*40*6 mm with 38 mm dia steel pullys with bolts, nuts locking attangement, stoppers handles complete including applying a priming coat of approved lead paint. Ch 10 S.I.No 518 |
| 4 | Indian Sal Wood wrought framed and fixed including simple mouldings, straight work as in chaukhats including supply of all materials labour, Tools & plants etc. required for proper completion of the work Ch.9 S.I No. 403 |
| 5 | Supply and fixing of Indian Commercial flush shutters 32mm. Thick (excluding cost of all fitting) S.I No 471a |
| 6 | Supply and fixing of 2.5 cm. thick teak wood door and window shutters with panels of heavy Quality galvanized iron wire gauge 2.5 mm. or 1.5 mm (1/10 or 1/12 or 1/16 inch) mesh or any other size, with necessary beading, including supply and fixing & adjustment of hinges, bolts, locks, handles spring and or other fittings but excluding their supply and including two coat of black japan on all iron fitting if necessary. Fitting with necessary screws to be supplied departmentally Ch. 9.26 |
| 7 | Painting or varnishing work in small areas or new wood work with one coat (up to one square metre) of ready mixed priming paint and one coat of approved superior wuality ready mixed paint or varnish including supply of all materials. Labour, tools & plants etc. required for proper completion of the work. Paint to be used ISI maked Ch. 15 S.I No. 641 |
| 8 | M.S or iron work of M.S.Grills/Stair case railing/gates/trusher/racks etc. such as holding down bolts, holdfast, tie rods grating etc. wrought to required from including supply of steel bolts, nuts wastage etc, and their fixing required for proper completion of the work Ch.10 S.I No. 502A |
| 9 | Painting on iron work with one coat priming and one coat of approved paint including supply of all material, labour, Tools, and plants etc. required for proper completion of the work. As per dirction of Engineer in charge S.I.No |
| 10 | Supply and fixing of 06 to 8 mm thick ivory or light shades witerfied tiles 600*600 mm size in flooring and skirting with 1:3 approved cement and coarse sand morter finished with in its cement colour slurry, joining and polished of aapproved quality complete, including supply of all materials, labour, tools and plants etc. required for proper completion of the work. as per direction of Engineer inm charge S.I. NO. teak wood door and window shutters with panels of heavy Quality galvanized iron wire gauge 2.5 mm. or 1.5 mm (1/10 or 1/12 or 1/16 inch) mesh or any other size, with necessary beading, including supply and fixing & adjustment of hinges, bolts, locks, handles spring and or other fittings but excluding their supply and including two coat of black japan on all iron fitting if necessary. Fitting with necessary screws to be supplied departmentally Ch. 9.26 |
| 11 | Providing wall putty on old surface with approved quality material of Berger/J.K/Birla or similar make 2 coat. (New Item) |
| 12 | Finishing wall with weather coat of approved make and quality on new work with two coat to give an even shade including supply of all materials, labour, Tools&plant etc. required for proper completion of the work. SI No 662 New item |
| 13 | Providing and fixing vitreous china dunl purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C. pan) with seat & lid fixed with C.P.brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over 14 now pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:Ch.21(B) S.I.No.21.29 |
| 14 | Providing and fixing C.P.brass long nose bib cock of approved quality confirming to ISI standards and weighing not less than 810 gms.S.L.No.21.08 |
| 15 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot&cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed including cutting chases and making good the wall etc.S.L.No.21.02 work, 20MM Dia |
| 16 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot&cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed including cutting chases and making good the wall etc.S.L.No.21.02 work, 25MM Dia |
| 17 | Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 17 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. Ch.21(B)SI.No.21.16 |
| 18 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS1:12701 marked (Sintex or equivalent) with cover and suitable locking 18 arrangement and making necessary holes for inlet, outlet and over flow pipes but with out fittings and the base support for tank complete as per direction of Engineer-in-charge. Ch.21(B)Sl.No.21.11 (Qty) Please Enable Macros to View BoQ information |
