|
| 1 | M & L for taking down the Defective Electric Induction Motor of 120 HP Capacity of Kirloskar make 415 Volt, 3 Phase by dismantling the electrical connections, decoupling with pump, removing the motor from bed, transporting to workshop, dismantling the burnt out winding from Rotor/Stator and rewinding the Rotor or Stator with same type Super Enamelled Copper Conductor of same Gauge, Weight, same Number of turns and with necessary Insulating Material, Varnishing, Backing, replacement of Bearings with new Bearings, worn-out bushes, connectors, Terminal Plate, Re-assembling the motor completely transporting back to site and fixing back in original position aligning with the Pump, connecting cable through terminal block, applying Two coats of synthetic enamel paint of approved tint including preparation of surfaces and including testing and commissioning on completion, complete all as specified and as directed. |
| 2 | All as per Serial Item No. 01 above but Electric Motorof Capacity 60 to 75 HP, 415 Volt, 3 Phase, 50 Hz of Make Kirloskar / C & G complete all as specified and as directed. |
| 3 | All as per Serial Item No. 01 above but Centrifugal Pump Motor of Capacity 20 HP, 415 Volt, 3 Phase, 50 Hz of Make Kirloskar / C & G complete all as specified and as directed. |
| 4 | M & L for Overhauling of Centrifugal Pump Set of 120 HP Capacity of Make Kirloskar, by Disconnecting the Suction & Delivery lines, Dismantling completely and replacing unserviceable Ball Bearings, Shaft Sleeve, Gland, Neck Ring, Gland Rope Shield, Unserviceable Nut, Bolt, Washer etc. and Re-assembling the Pump Set completely and fixing back in original position, Reconnecting back the Suction & Delivery Lines, realigning and connecting cable through terminal block applying Two coats of synthetic enamel paint of approved tint including preparation of surfaces and including testing and commissioning on completion, complete all as specified and as directed. |
| 5 | All as per Serial Item No. 04 above but Centrifugal Pump Set of Capacity 60 to 75 HP complete all as specified and as directed. |
| 6 | All as per Serial Item No. 04 above but Centrifugal Pump Set of Capacity 20 HP complete all as specified and as directed. |
| 7 | S & F in repairs CI Flexible Coupling with Spider Rubber Element suitable for 120 HP Capacity Motors / Pumps including Keys, Nuts, Bolts, Washers etc. Alignment of Motor and Pump and including testing and commissioning on completion, complete all as specified and as directed. |
| 8 | S & F in repairs CI Flexible Coupling with Spider Rubber Element suitable for 60 to 75 HP Capacity Motors / Pumps including Keys, Nuts, Bolts, Washers etc. Alignment of Motor and Pump and including testing and commissioning on completion, complete all as specified and as directed. |
| 9 | S & F in repairs CI Flexible Coupling with Spider Rubber Element suitable for 20 HP Capacity Motors / Pumps including Keys, Nuts, Bolts, Washers etc. Alignment of Motor and Pump and including testing and commissioning on completion, complete all as specified and as directed. |
| 10 | S & F in repairs Terminal Block suitable for 120 HP Capacity Motors / Pumps complete all as specified and as directed. |
| 11 | S & F in repairs Terminal Block suitable for 60 to 75 HP Capacity Motors / Pumps complete all as specified and as directed. |
| 12 | S & F in repairs Terminal Block suitable for 20 HP Capacity Motors / Pumps complete all as specified and as directed. |
| 13 | S & F in repairs Power Contactor, ML-1.5 along with Timer Switch and Overload Relay by disconnecting Control Wiring from existing Panel Board including renewal of Copper Lugs etc. complete all as specified and as directed. |
| 14 | S & F in repairs Power Contactor, ML-2 along with Timer Switch and Overload Relay by disconnecting Control Wiring from existing Panel Board including renewal of Copper Lugs etc. complete all as specified and as directed. |
| 15 | S & F in repairs Power Contactor, ML-3 along with Timer Switch and Overload Relay by disconnecting Control Wiring from existing Panel Board including renewal of Copper Lugs etc. complete all as specified and as directed. |
| 16 | S & F in repairs Power Contactor, ML-4 along with Timer Switch and Overload Relay by disconnecting Control Wiring from existing Panel Board including renewal of Copper Lugs etc. complete all as specified and as directed. |
| 17 | S & F in repairs Power Contactor, ML-6 along with Timer Switch and Overload Relay by disconnecting Control Wiring from existing Panel Board including renewal of Copper Lugs etc. complete all as specified and as directed. |
| 18 | S & F in repairs, Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 20 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed. |
| 19 | S & F in repairs, Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed. |
| 20 | S & F in repairs, Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 40 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed. |
| 21 | S & F in repairs, Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 50 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed. |
| 22 | S & F in repairs Foot Valve, Cast Iron Body, 200mm bore with Flanged ends of any pattern with Bypass Arrangement and Confirming to IS – 4038, Class PN 2.0, ISI Marked having Gunmetal Disc Face Ring, Nitrile Rubber, Hinge Pin of Stainless Steel AISI-410 with Cast Iron Bolted Stainer including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed. |
| 23 | S & F in repairs Foot Valve, Cast Iron Body, 150mm bore with Flanged ends of any pattern with Bypass Arrangement and Confirming to IS – 4038, Class PN 2.0, ISI Marked having Gunmetal Disc Face Ring, Nitrile Rubber, Hinge Pin of Stainless Steel AISI-410 with Cast Iron Bolted Stainer including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed. |
| 24 | Taking out Sluice Valves of 80mm dia, refacing, regrinding, cleaning & removing rust, old rubber washers and refixing by providing New Gland Packing, Check Nuts, Spindle in same position or new location by using new Nuts, Bolts, Rubber Gaskets & testing and commissioning including applying two coats of synthetic enamel paint [Black] complete all as specified and as directed. |
| 25 | Taking out Sluice Valves of 150mm dia, refacing, regrinding, cleaning & removing rust, old rubber washers and refixing by providing New Gland Packing, Check Nuts, Spindle in same position or new location by using new Nuts, Bolts, Rubber Gaskets & testing and commissioning including applying two coats of synthetic enamel paint [Black] complete all as specified and as directed. |
| 26 | Taking out Sluice Valves of 200mm dia, refacing, regrinding, cleaning & removing rust, old rubber washers and refixing by providing New Gland Packing, Check Nuts, Spindle in same position or new location by using new Nuts, Bolts, Rubber Gaskets & testing and commissioning including applying two coats of synthetic enamel paint [Black] complete all as specified and as directed. |
| 27 | S & F Pressure Gauge of capacity 0 to 14 KG/cm², with 100mm size Dial including necessary specials and provision of suitable ferrule etc. including taking down existing unserviceable gauge complete all as specified and as directed. [Make: RMCO/ Uday/ H-Guru] |
| 28 | S & F Cast Iron Non Return Valve with bypass arrangement with suitable flanges, suitable for 200 mm bore pipes confirming to IS – 5312, Class PN –1.6, including necessary nuts, bolts, washers, rubber gasket etc for jointing including taking down existing Non Return Valve of any description complete all as specified and as directed. |
| 29 | S & F Cast Iron Non Return Valve with bypass arrangement with suitable flanges, suitable for 150 mm bore pipes confirming to IS – 5312, Class PN –1.6, including necessary nuts, bolts, washers, rubber gasket etc for jointing including taking down existing Non Return Valve of any description complete all as specified and as directed. |
| 30 | S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 80 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer including taking down existing Sluice Valve of any description complete all as specified and as directed. |
| 31 | S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 150 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer including taking down existing Sluice Valve of any description complete all as specified and as directed. |
| 32 | S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 200 mm Dia, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer including taking down existing Sluice Valve of any description complete all as specified and as directed. |
| 33 | Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep in Soft / Loose soil for laying Pipes / Cables etc. complete all as specified and as directed. |
| 34 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. |
| 35 | Removal of excavated material [Soil] to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m complete all as specified and as directed. |
| 36 | Taking down or up steel tubing and connections for 40 mm bore of pipe complete all as specified and as directed. |
| 37 | Taking down or up steel tubing and connections for 50 mm bore of pipe complete all as specified and as directed. |
| 38 | Refixing Old GI/MS water tubing of 40 mm bore, medium grade including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. |
| 39 | Refixing Old GI/MS water tubing of 50 mm bore, medium grade including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. |
| 40 | Supplying and laying GI Tubing of 40 mm bore, Medium Grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc. fixed to walls, ceiling or laid on floors or laid in trenches including testing complete all as specified and as directed. Note: Earth work and excavation will be measured and paid separately. |
| 41 | Supplying and laying GI Tubing of 50 mm bore, Medium Grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc. fixed to walls, ceiling or laid on floors or laid in trenches including testing complete all as specified and as directed. Note: Earth work and excavation will be measured and paid separately. |
| 42 | Supplying and laying MS ERW Pipe, 150 mm bore, Medium Grade, conforming to IS – 1239 including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., welding to CI / MS Pipes to make leak proof joints, laid in floors or fixed to walls and ceilings including testing including applying two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer and taking down existing MS Pipe of any description and in any position complete all as specified and as directed. |
| 43 | Supplying and laying MS ERW Pipe, 300 mm bore, Medium Grade, conforming to IS – 3589 including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., welding to CI / MS Pipes to make leak proof joints, laid in floors or fixed to walls and ceilings including testing including applying two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer and taking down existing MS Pipe of any description and in any position complete all as specified and as directed. |
| 44 | M & L for Construction of Valve Chamber of size 1050 X 1050 X 1050 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Fly Ash Bricks in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises, demolition of existing Valve Chamber of any description complete all as specified and shown on drawing CEDD / TD / 119, Sheet No. 1 / 1 dated 20 August 1983, revised up to 21 September 1992. |
| 45 | M & L for Construction of Valve Chamber of size 900 X 900 X 600 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Fly Ash Bricks in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises, demolition of existing Valve Chamber of any description complete all as specified and shown on drawing CEDD / TD / 119, Sheet No. 1 / 1 dated 20 August 1983, revised up to 21 September 1992. Please Enable Macros to View BoQ information |
| 46 | M & L for Construction of Valve Chamber of size 900 X 900 X 600 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Fly Ash Bricks in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises, demolition of existing Valve Chamber of any description complete all as specified and shown on drawing CEDD / TD / 119, Sheet No. 1 / 1 dated 20 August 1983, revised up to 21 September 1992. Please Enable Macros to View BoQ information |
