|
| 1 | M&L for providing filling epoxy putty into crack after opening up cracks in V-groove manner approximate 5 x 5mm size using mechanical cutter,properly cleaning the same to remove loose dust dirt etc and filling the same using three component,solvent free,Thyxotropic,Epoxy resin based putty having 100% solid contents,density of 1.64-1.68 gm/cc,comprehensive strength @7days- 50N/mm², pot life 40 minutes at 25°C,drying time 8 hrs at 25°C. Recoatable time 24 hrs after finishing in line and level with existing concrete surface etc. complete all as specified and directed by the Engineer-in-Charge Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Dr. Fixit (Pidilite Industries), Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 2 | M&L for removing of existing loose material and complete surface preparation by scarifying the surface. Filling of voids and undaltions with ingle component thixotropic fibre reinforced polymer modified mortar to achieve compressive strengths of 15 Mpa in 1 day, 25MPa in 3 days and 45 MPA in 28 days, adhesion bond strength of>2MPa, giving creep strain reduction of 10%, modulus of elasticity of 25-28 MPa, shall have water-powder ratio of 0.16,finished to obtain surface even and smooth, complete all as specified and directed by Engr-in- charge.Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 3 | M&L for applying 3 coats of coating- non-toxic waterproofing system should have multiple corrosion inhibiting synergies carefully graded aggregrates in combination with selected polymers, which should have good uv resistant capability, highly flexible, having crack bridging capabilities upto 1 mm etc.Before applying ,surface should be free from dirt soil, oil release agents latiance and any foreign material which may unpair the bond, penetration.It cures forming a coating, with limited thickness, which resists the penetration of water . The coating to be applied on concrete surfaces shall be acrylic polymer based cementitious composite water proof coating system.properties- High perforMance elastomeric cementations Non-toxic waterproofing coating complies to ASTM D4541 ASTM C836, DIN 1.048p 5 ASTC D412 having shore hardness D Scale = 20 Non Volatile, Low Temperature Feasibility Test, Tensile strength > 0.4 Mpa, Elongation > 20% . It shall be non- flammable, non - combustible. It shall give tough and hard waterproofing surface. I shall allow entrapped vapour to escape preventing peeling and blistering. I shall have excellent bond to building materials. I shall be highly durable in continuous wet condition. The solid content shall be 30 ± 1 % and the specific gravity shall be ranging between 1.05 ± 0.05 gm/cc.System should be application of 3 coats of coating using brush, roller or by trowel .Coating to be applied after proper surface preparation to remove loose dust, cleaning, mixing using slow speed electric drill and application of 3 coats complete all specified and directed by Engineer-in-charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 4 | M&L for providing 10 mm thick one component chloride free thixotropic fibre reinforced polymer modified repair mortar with alkali resistant synthetic fibres for exceptional resistance cracking complies ASTMC 109 with flexural strength ASTM C 348 @ 7 days meeting 7N/mm2, tensile strength @ 7days (ASTM C 307)> 3 N/mm2, compressive strength of 35Mpa at 7 day and 45Mpa at 28 days, Adhesion bond strength > 2 N/mm2 ,Creep Strain Reduction - 10% at the outer or inner RCC surface . Cement and sand can be used to make the surface even and smooth. It should be specially adhered to BS 6319 having specific gravity of 1.025 to 1.04, minimum 43% solid contents complete all as specified and as directed.Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 5 | M&L for applying 20mm shear thinning fibre reinforced polymer modified , impermeable to aggressive elements, dual shrinkage compensated, cementitious repair mortar with alkali resistant synthetic fibres for exceptional resistance cracking complies ASTM C 109 with flexural strength ASTM C 348 @ 7 days meeting 7N/sqmm, tensile strength @ 7days (ASTM C 307)> 3 N/sqmm, compressive strength of 35MPa at 7 day and 45MPa at 28 days, at the outer or inner RCC, which provides excellent bond to concrete, Improves tensile and flexural properties of mortar, Versatile having specific gravity of 1.02 Cement and sand can be used to make the surface even and smooth . complete all as specified and directed by Engr-in-charge.Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 6 | M&L for applying Polyster Resin based Anchoring material in concrete before fixing nozzle it should typically attains a compressive strength in excess of 20N/mm @ 3 hours and and ultimate compressive strength of 70N/mm in 7 days (50mm x 50mm x 50mm)when tested as per BS 6319 Part 2 : 1983. complete all as specified and directed by Engr-in-charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 7 | M&L for treating the existing pipe penetrations using non-shrink, free flowing, cementitious grout .The compressive strength of the grout must exceed 50 N/mm2 at 7 days and 60 N/mm2 at 28 days. The flexural strength of grout must exceed 9N/mm2 @ 28 days. Fresh wet density of the mixed grout must exceed 2150 kg/m3. Further flashing the area using solvent based UV resistant polyurethane based waterproofing material having minimum tensile strength on 4 N/mm2 and minimum elongation of 800%. Complete all as specified and directed by Engineer-in-charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 8 | M&L for applying 2 coats of amine cured epoxy coating cum primer of film thickness of approx. 1 to 2mm should be built up in two coats, should achieve Adhesion bond strength 1 N/mm2, pot life of 30 minutes@30 C. Before applying primer Concrete / steel surface should be cleaned by any suitable method (like sand blasting, water jetting etc.) to remove old coatings, grease, oil, curing compounds, loose particles, weld spatter, flux, rust etc, complete all specified and directed by Engineer-in-charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 9 | M&L for Perforation in RC using twist & rotating mechanical cutting tool for Fastening to concrete for chemical anchoring having a Rapid strength gain, Vibration resistant, Corrosion resistant of reinforcement on existing RC Component with Hilti HIT-HY70 BS 5080 or equivalent as approved by GE, typically attains a compressive strength in excess of 20N/sqmm @ 3 hours and an ultimate compressive strength of 70N/sqmm in 7 days as per BS 6319 Part 2 : 1983, maximum hole depth 75mm, steel bar 12mm dia and drill bit size14mm with polyster resin based anchoring material for H/V/Large annular applications or post installed bars or in accordance with bar thickness complete all as specified and directed by Engr-in-charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 10 | M&L for dismantling/taking down old existing unserviceable cement plaster loose/unsound weaken cement concrete of any description and in any position from existing external/internal surfaces of RCC/slab/beam/columns RCC facies etc. average depth 15mm (approx. height upto 15 mtr from natural ground level) with power driven of penumetic chisel and removal upto the approval municipal dumping ground outsides MOD land including cutting of all edges, making square shoulders of the cavities roughening the smooth surfaces, scrapping out/removing corrosion all loose/scale/rust etc from the visible reinforcement by applying rust remover and cleaning the steel reinforcement properly and then applying single component cementations on visible reinforcement surfaces to form a continuous film not less than 1mm thick and preparing the surface to receive concert of epoxy grout mortar act including providing necessary proportions, bracing and runners to relieve the members form the load comming on it including scaffolding with working plat form as required and as per design and pattern including preparing the surface to match with the existing surface, complete all as specified and directed by Engr-in-charge..Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 11 | M&L for repair to damaged existing surfaces of upto 15 m height from plinth level by structural strengthening using epoxy injection grouting Complete all as specified and as directed and as under :-(a).High strength epoxy resin based Injection Grouting, Automatic NRV packers in all column and beams from all access side Distance of injections will be 500 m c/c in matrix pattern until column is submerged in dampness of chemical et(b) injection grouting using two component grouting polymer having low viscosity, high molecular weight, thermosetting to reach very deep pores, voids, cracks and honeycomb in the concrete, specific gravity of which shall be 0.95, pH of 2-4,viscosity of 20-25 sec by B/4 ford cup and having curing time of 30-90 minutes area by suitable gun/pump at required pressure (100 bar to 150 Bar, including cutting of nipples after curing etc and sealing the nozzles with epoxy putty and preparing the surface to match with the existing surfaces all as directed. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd. |
| 12 | M&L for form work to sides and soffits of lintels, beams, columns, shelves, chajjas including overhangs etc for fair finished flat surface, complete all as specified and directed by Engr-in-charge |
| 13 | M&L for applying 2 coats of mixture of two monomer unsaturated liquid hydrocarbon , gaseous hydrocarbon and polymesrized them to get the high polymer dispersion emulsion successfully bonded to mortar, to improve adhesion to concrete, better durability, reduced shrinkage and increased flexibility and resistant to emulsification in damp condition modified Ensuring no porosity in new/old surface, temperatures between +5°C and +35°C, Resist to penetration of CO2 4.600 micron , compressive strength (11.5 N/mm2) at 3days strength - 11.5 (N/sqmm ) and at 28 days - 25.30N/sqmm complete all as specified and directed by Engr-in-charge.Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 14 | M & L for curing of the surface using low viscosity emulsion which incorporate a special alkali reactive emulsion breaking system. It shoud be non-penetrating continuous filmcomplies with the internationally recognized ASTM C309-90 standards including all tools and tackels complete all as specified and directed by Engineer-in-Charge @ 250gms/Sqm. Product should have daylight Reflectance of 70% as per ASTM E-1347.complete all specified and directed by engineer-in-charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 15 | M&L for MS TMT bars 12 mm dia and over as in reinforcement cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends & binding with and including MS annealed wire not less than 0.9 mm dia complete all as specified and directed by Engineer in Charge. |
| 16 | M&L for providing and applying a blend of Portland cement, graded fillers and chemical aditives which impart controlled expansion, should be ready to use and can fill convoluted voids, componsates shrikage at both plastic and Hardened states. Minimum thickness to be used is 50mm with addition of 10mm down aggregates of 25% of the weight of ready to use powder with W/P ratio of 0.18. Strength of 1 day to be 20N/mm2. Time of expansion to start after 20min of mixing and finish in 120 min of mixing. Epoxy bonding agent having mix density of 1.45 to 1.5 kg/ltr, compressive strength (BS-6319 PT 3)-25 Mpa at 7 days bond strength (ASTM C 881)-11 N/mm2 at 7 days, having an over lay time of 3 hrs at 30°C Cement and sand can be used to make the surface even and smooth including all tools and tackles as per accepting officer, complete all as specified and directed by Engr-in-Charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 17 | M&L for removing old existing rubbish/battered/useless mixture of the binding materials such as cement / Lime and fine aggregate (<4.5mm retained on IS Sieve), loose/unsound weaken mixture of binding materials such as cement / Lime and coarse Aggregate (>4.5mm retained on IS Sieve), fine Aggregate of any description and in any position from existing external/internal surfaces of RCC components or any surface having average profundity of 15mm (Approx height 10m from natural ground level) by hand tool that has a long metal blade with a sharp edge at the end, chisel and hammer or using robust pneumatic chisel hand tools and removal beyond MoD land including cutting of all edges, making square shoulders of the aperture, coarsen the smooth surfaces, curettage /removing of all deterioted/decayed loose surface.complete all as specified and directed by Engr-in-charge.Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 18 | M&L for providing and fixing welded MS wire mesh weighing not less than 1Kg/Sqm of size 50mmX50mm of 2 mm dia on the prepared surface & surface should be cleaned and be removed from dirt, fungus and all foreign material complete all as specified and directed by Engineer in Charge. |
| 19 | M&L for providing and applying 3 coats of liquid-applied, single-component, moisture-reactive, hydrophobic elastomeric membrane over exposed l surfaces, forming a seamless and continuously bonded protective layer.The cured film shall be permanently elastic, UV-stable and chemically resistant, capable of accommodating thermal movement and micro-crack bridging, and conforming to ASTM D624, ASTM D412, DIN 16726 and ASTM D903, with minimum tensile strength > 4 N/mm², elongation > 800%, puncture resistance ≥ 290 N and Shore A hardness ≈ 65. The material shall exhibit controlled rheology with a working pot life of 30–35 min at 20 °C. Surface conditioning shall include removal of contaminants and loose matter, mechanical mixing by slow-speed electric agitator and uniform brush/roller application of two coats with regulated coverage and inter-coat intervals. Item includes all materials, labour, tools, plant, consumables and incidental works, complete as specified and as directed by the Engineer-in-Charge.Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 20 | M&L for Providing and executing application in 2 successive coats of a single-component, aromatic elastomeric resin–based priming formulation of low inherent viscosity and pronounced penetrative characteristics, over suitably conditioned cementitious and/or metallic substrates, so as to achieve a resultant nominal dry film build in the order of 40–50 microns, inclusive of all preparatory and enabling measures required to render the substrate acceptable for coating works, comprising mechanical grinding or equivalent surface treatment for elimination of laitance, contaminants, oil residues, friable matter and legacy coatings, verification of substrate maturity and controlled moisture condition, followed by mechanical conditioning of the material at appropriate rotational speed to attain uniform homogeneity and release of entrapped air, and subsequent application by approved manual and/or mechanized means with adequate inter-coat interval not less than the minimum stabilization period, resulting in a continuous, coherent and chemically resistant primed interface exhibiting enhanced adhesion and flexibility, capable of receiving subsequent treatment layers, with the material possessing a practical working life extending over several hours under normal ambient conditions and attaining surface-dry state within a limited duration, inclusive of all labour, materials, consumables, tools, plant, safety provisions, leads, lifts, scaffolding, temporary arrangements and incidentals whatsoever, complete all as specified and directed by Engr-in-Charge. Make : Thermax Ltd, Tiki tar Danosa(Pvt)Ltd,M/s Torchtar menbranes & bitumen products Pvt. Ltd., Asian Paints SmartCare, Sika India, UltraTech Cement, Berger Paints (HomeShield/WeatherCoat). |
| 21 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 22 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.; For thickness of tiles 10 mm to 25 mm |
| 23 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 24 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 25 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 26 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres |
| 27 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 28 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B ; Fixing with adjustable lugs with split end tail to each jamb |
| 29 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately):30 mm thick |
| 30 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge. |
| 31 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. : 30 mm thick pre laminated PVC door shutters |
| 32 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm |
| 33 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25 mm thick |
| 34 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 35 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete; Twin rubber stopper |
| 36 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 37 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100x10 mm |
| 38 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm |
| 39 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
| 40 | Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With F.P.S.(non modular) bricks |
| 41 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources |
| 42 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : : Rectangular shape 1500x450 mm |
| 43 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. : 110 mm diameter |
| 44 | Bend 87.5° 110 mm bend |
| 45 | Single tee without door : 110x110x110 mm |
| 46 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm nominal dia Pipes |
| 47 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal dia Pipes |
| 48 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore |
| 49 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore |
| 50 | Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore |
| 51 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.: Semi rigid pipe: 32 mm dia |
| 52 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 53 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. Long pattern W.C Pan of size 580x440 mm |
| 54 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively |
| 55 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 56 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 57 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 58 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 59 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 60 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work over on under coat suitable shed with odinary paint of approved brand and manufecture. |
| 61 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) |
| 62 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 63 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 64 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 65 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) |
| 66 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. sqm 285.00 Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done |
| 67 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 68 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 40 mm nominal bore |
| 69 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 50 mm nominal bore |
| 70 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 65 mm nominal bore |
| 71 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore |
| 72 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore |
| 73 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore |
| 74 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore |
| 75 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 65 mm dia nominal bore |
| 76 | Dismantling of manhole including R.C.C. top slab, C.I. cover with frame, including stacking of useful materials near the site and disposal of unserviceable materials within 50 m lead as per direction of Engineer-in-charge:Rectangular manhole 90x80 cm and 45 cm deep |
| 77 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 78 | Dismantling of road gully chamber of various sizes including C.I. grating with frame including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead including refilling the excavated gap. |
| 79 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 80 | Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia upto 300mm |
| 81 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe |
| 82 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : ; All kinds of soil: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Please Enable Macros to View BoQ information |
