|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: |
| 2 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural resources : 4 graded stone aggregate 20 mm nominal size) derived from natural resources |
| 3 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 4 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 5 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 6 | In gratings, frames, guard bar, ladder, railings, brackets,gates and similar works |
| 7 | Making khurras 45x45 cm with average minimum thickness of5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 8 | Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C. battens or structural steel sections (Karries or battens or structural steel sections to be paid separately), including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete : |
| 9 | White sand stone slab : |
| 10 | 40 to 50 mm thick |
| 11 | Providing and fixing on wall face unplasticised Rigid PVC rain water/soil waste pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. |
| 12 | 110 mm diameter |
| 13 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. |
| 14 | Coupler |
| 15 | 110mm |
| 16 | Bend 87.5° |
| 17 | 110 mm bend |
| 18 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 19 | 12 mm cement plaster of mix: |
| 20 | 1:6 (1 cement: 6 coarse sand) |
| 21 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 22 | 1:6 (1 cement: 6 coarse sand) |
| 23 | Neat cement punning. |
| 24 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : |
| 25 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 26 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 27 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 28 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. |
| 29 | In cement mortar |
| 30 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 31 | G.S. Sheet |
| 32 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 33 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 34 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 35 | 10 litre capacity - White |
| 36 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 37 | Semi rigid pipe |
| 38 | 32 mm dia |
| 39 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 40 | 20 mm nominal outer dia .Pipes. |
| 41 | 25 mm nominal outer dia .Pipes. |
| 42 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 43 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 44 | 15 mm nominal bore, 122 mm long. Weighing not less than 99 gms. |
| 45 | Providing and fixing PTMT stop cock of approved quality and colour. |
| 46 | 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 47 | Providing and fixing PTMT pillar tap of approved quality and colour. |
| 48 | 15 mm nominal bore, 125 mm long. Weighing not less than 120 gms. |
| 49 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. |
| 50 | 25 mm nominal bore, 152 mm long. Weighing not less than 440 gms. |
| 51 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 52 | 15 mm nominal bore with 45 cm length. |
| 53 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. |
| 54 | 20mm nominal bore. Weighing not less than 40 gms. |
| 55 | 25mm nominal bore. Weighing not less than 62 gms. |
| 56 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 57 | 50mm average thickness |
| 58 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. |
| 59 | SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approvedpolymer |
| 60 | Providing, mixing and applying SBR polymer (of approved make @ minimum 2% by wt. of cement used) modified plain/reinforced cement concrete for structural members having minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criteria] with specified average thickness. |
| 61 | 50mm thick in Grade M 25 with cement content not less than 330 kg per cum |
| 62 | Providing and fixing 3/4 mm thick polycarbonate sheet of required size to glazed windows by silicon adhesive i/c cleanind and raking existing putty etc all complete as per direction of EIC. |
| 63 | Providing and fixing CPVC Union in CPVC pipe including cutting and pasting the pipe and making good etc. complete |
| 64 | 20 mm nominal outer dia .Pipes. |
| 65 | 25 mm nominal outer dia .Pipes. |
| 66 | Providing and fixing CPVC Gate valve in CPVC pipe including cutting and pasting the pipe and making good etc. complete |
| 67 | 20 mm nominal outer dia .Pipes. |
| 68 | 25 mm nominal outer dia .Pipes. |
| 69 | Providing and fixing CPVC specials FTA/MTA/brass fittings in CPVC pipe line wherever required including cutting and pasting the pipe with cement solvant etc. all complete |
| 70 | Credit to dismantled unserviceable GS sheet (4kg/sqm) |
| 71 | Providing and laying waterproofing treatment over the existing roof as directed by E-I-C and consisting of: |
| 72 | Cleaning and washing of the surface of existing roof to make it free from dust, oil, grease and loose particles by brushing properly exposing rugged surface and final washing. |
| 73 | Surface cleaning and crack filling: Repairing the damaged surface with Terroza ready plast, widening and deepening of cracks and fill all cracks by terraoza crack filler overlapping 25 mm on either side. |
| 74 | Moisturing the surface and application of Terroseal evenly over the surface to penetrate deep inside the poresand create elastomeric filmover it. |
| 75 | Application of heavy duty reinforced glass fibre net (Terromesh) of high tensile strength and alkali resistance over the surface covering vertical side walls. |
| 76 | Application of second coat Terroseal uniformly over the Terromesh. |
| 77 | Application of Terroza water proofing compound with water and terroseal over the surface with rolleror trowel like gurmala plaster to form a hydrophobic barrier for water and insulate the surface from heat and cold. |
| 78 | After complete drying of surface application of Terroza building guard in two or more coats with brush or roller and allow it to dry completely to seal the surface in all respect. Please Enable Macros to View BoQ information |
