|
| 1 | Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. |
| 2 | (b) Depth of excavation additional depth beyond 1,500 mm. and up to 3,000 mm. but not requiring shoring. |
| 3 | Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm. including watering and ramming etc.layer by layer complete .(payment to be made on the basis of measurement of finished quantity of work). |
| 4 | (a) With earth obtained from excavation of foundation. |
| 5 | Laying 150 mm. to 200 mm. boulder soling including rough dressing hand packing and ramming down small pieces in the interstics including rolling and preparing the bed to proper level and filling up all joints with sandy clay or earth. |
| 6 | Cost of stone boulder 150 mm size delivered ans stacked at site. |
| 7 | (I) Cement concrete with graded stone ballast (40 mm size) excluding shuttering.In ground floor. |
| 8 | (B) With N.B variety stone metal. |
| 9 | (a) 1:3:6 proportion. |
| 10 | Rubble masonry in cement (1:6) with hard dressed stones from approved quarries and clean, coarse and washed sand including carriage of all materials to site |
| 11 | In Fine dressed work in Building |
| 12 | In Ground Floor |
| 13 | Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant codes. |
| 14 | (ii) River bazree. |
| 15 | Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). |
| 16 | (a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction of the Engineer-in-charge. . |
| 17 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. |
| 18 | (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel. |
| 19 | SAIL/ TATA/RINL |
| 20 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. (Add. above ground floor - 1st. floor) |
| 21 | Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. |
| 22 | (ii) With 1:4 cement mortar . |
| 23 | (a) 20 mm.thick plaster. |
| 24 | (i) with 1:6 cement mortar. |
| 25 | (a) 25 mm. thick plaster. |
| 26 | Supplying, fitting and fixing Black Stone slab used in Kitchenslab, alcove, wardrobe etc. laid and jointed with necessaryadhesive Cement mortar (1:2) including grinding or polishingas per direction of Engineer-in -Charge in Ground Floor |
| 27 | (a) Slab Thickness 20 to 25 mm |
| 28 | Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. |
| 29 | (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. |
| 30 | (b) Area of each tile the above 0.09Sq.m. |
| 31 | (ii) Other than Coloured decorative including white. |
| 32 | Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. |
| 33 | (B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. |
| 34 | (b) Area of each tile the above 0.09Sq.m. |
| 35 | (ii) Other than Coloured decorative including white. |
| 36 | Rendering the Surface of walls and ceiling with White Cement baseWATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 37 | Applying exterior grade Acrylic primer of approved quality and brand on plaster or concrete surface old or new surface to receive decorative textured (mat finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor:. |
| 38 | (b) two coat. |
| 39 | Applying interior grade acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to received distemper /Acrylic emulsion paint including scraping and preparing the surface thoroughly , complete as per manufactured specification and as per directions of the EIC.In ground floor. |
| 40 | (b) two coats. |
| 41 | (ii) solvent based interior grade Acrylic primer. |
| 42 | Protective and decorative Acrylic exterior emulsion paint of approved quality , as per manufacture specification as per direction of EIC to be apply over Acrylic primer as required. the rate included cost of material , labour scaffoldic and all incidential charges but excluding the cost of primer.In ground floor ( two coat). |
| 43 | (b) Premium 100% Acrylic emulsion. |
| 44 | Applying acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermediated coats including putty ( to be done under specific instructions of superintending engineer): (two coats). |
| 45 | (i) standard quality. |
| 46 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals). |
| 47 | (f) sishu , Gamar, champ, badam, bhola, mogra, Hallak. |
| 48 | Glazed shutters of doors, window, fan light, clerestory windows etc. as per design (with ordinary glass of 7.4 kg./sq.m.,3 mm. thick) fitted with putty bed and teak wood bead and nails including fitting and fixing shutter in position but excluding the cost of hinges and other fittings , cost of glass , putty, wooden beads etc which will be paid separately.in ground floor. |
| 49 | (i) 40 mm. thick shutters. |
| 50 | (b) sishu,gamar,Champ,badam,bhola, mogra,Hallak, |
| 51 | supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). |
| 52 | (a) 40mm x 6mm, 250mm Length . |
| 53 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. |
| 54 | (v) 75 mm x 60 mm x 3.15 mm. |
| 55 | Iron catch hook of approved quality fitted and fixed to shutter and chowkat. |
| 56 | (b) 6 mm dia x 225 mm long. |
| 57 | Iron skeleton bolt of approved quality fitted and fixed complete. |
| 58 | (a) 375 mm long x 10 mm dia rod. |
| 59 | (iii) Steel body foot - door holder. |
| 60 | Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. |
| 61 | (iv) 150 mm long x 10 mm dia. bolt. |
| 62 | (iv) 150 mm long x 10 mm dia. bolt. |
| 63 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. |
| 64 | (a) With continuous plate base (hexagonal/round rod). |
| 65 | (ii) 100 mm grip x 10 mm dia rod . |
| 66 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. |
| 67 | (a) With continuous plate base (hexagonal/round rod). |
| 68 | (vii) 150 mm grip x 12 mm dia rod. |
| 69 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete (In all floors for internal wall & upto 6m height for external wall ). |
| 70 | (ii) 4 mm. thick. |
| 71 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor |
| 72 | (a) 35 mm thick shutters (single leaf) |
| 73 | (i) Brass floor door stopper. |
| 74 | (b) Priming one coat on timber or plastered surface with synthetic enamel oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 75 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. |
| 76 | (a) On timber or plastered surface: . |
| 77 | (1) With super gloss (hi-gloss). |
| 78 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. |
| 79 | (A) UPVC PIPES. |
| 80 | (ii) 110mm Dia. |
| 81 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806- 1957 & IS: 1161- 1958 connected to one another with bracket,gusset,cleats as per design, direction of Engineer-In-Charge complete including cutting to requisite size. fabrication with necessary metal arc welding conforming to IS: 816- 1956 & IS: 9595 using electrodes of approved make and brand conforming to IS: 814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section. consumables such as electrodes, gas and hire charges of all tools and plants and labour required for the work including all incidental charges such as electricity charges, labour insurance charges etc.(Payment to be made on the basis of calculated weight of structural tubular members as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with the weight of finished structural members. The rates are considere |
| 82 | (i) For trusses spanning up to 12.00 m. |
| 83 | Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150grams per sq. metre (followed by colour coated on both side) steel sheetwork having minimum yield strength of 550 Mpa of trapizoidal profile ofapproved make as per IS: 15965: 2012 and IS: 14246: 2013 (excludingthe supporting frame work) fitted and fixed with 55 mm & 25 mm selftapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc.complete with 150 mm end lap and one corrugation minimum side lap.(Payment to be made on area of finished work). In roof With .5mm thick sheet. |
| 84 | Galvanised iron sheet ridging fitted with necessary bolt, screws, washers etc complete. (225 mm end lapping). |
| 85 | (B) 450 mm laping each way. |
| 86 | (a) with 0.60 mm.thick sheet. |
| 87 | Galvanized iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm.M.S.flat bar clamps bent to design, bolts. Nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping). |
| 88 | (a) 225 mm. wide gutter. |
| 89 | Supplying & laying 3mm thick pre-fabricated plastomericwater proofing membrane conforming to EN 12311-1 &ASTMD 5147, manufactured with atactic poly propylene(APP) modified premium grade asphalt , specially reinforcedwith non-woven polyester core with polyester reinforcement@160 gms per sqm & both faces covered with thermo-fusiblepolyethylene film /MineraL on top face over a coat of primer@ 0.40 lit/sqm of manufacturer's specification onsmooth,clean dry surface prepared wherever required.Lapjoint shall be provided of 75 mm in longitudinal & 100 mm intransverse direction and fused using LPG/ Propane torchemploying extra care ensuring full bondage, completeremoval of entrapped air and sealing edges into grooves inappropriate manner as per direction of Engineer -in-chargeall complete including materials,labour and applicabletaxes. (Payment shall be made on the basis of finishedsurface area.).Membrane Property: Softening Point > 150 deg C, ColdFlexibility < -6 deg C, Tensile Strength, N/cm |
| 90 | Supplying and laying true to line and level Anti-Skid, Full Body,Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance withIS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr'shardness > 5.0, Staining resistance: Class-1, Water Absorption: E <0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thicklayer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles wi |
| 91 | a) In Ground Floor: Sizes-300 mm x300mm x10 mm with breaking strength > 1200 N |
| 92 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. |
| 93 | (A) UPVC PIPES. |
| 94 | (ii) 110mm Dia. |
| 95 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. |
| 96 | (B) UPVC fitting:. |
| 97 | (c)bend 87.5 degree. |
| 98 | (ii) 110mm Dia. |
| 99 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. |
| 100 | (B) UPVC fitting:. |
| 101 | (a) plain tee. |
| 102 | (ii) 110mm Dia. |
| 103 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. |
| 104 | (B) UPVC fitting:. |
| 105 | (d) shoe. |
| 106 | (ii) 110mm Dia. |
| 107 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc.complete in all respect including cost of necessary fitting as required, jointing materials and two coats of painting with approved paint in any position above ground.( Payment will be made on the center line measurements of total pipe line including all specials. No seperate payment will be made for accesorie, specials.). |
| 108 | For exposed work. |
| 109 | 15 mm dia.light quality. |
| 110 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc.complete in all respect including cost of necessary fitting as required, jointing materials and two coats of painting with approved paint in any position above ground.( Payment will be made on the center line measurements of total pipe line including all specials. No seperate payment will be made for accesorie, specials.). |
| 111 | For exposed work. |
| 112 | 40 mm dia.ligth quality. |
| 113 | Supplying, fitting and fixing PVC pipes of approved make of of Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made seperately). |
| 114 | For Concealed Work. |
| 115 | 15 mm. |
| 116 | Wash basin white vitreous china of approved make (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm wood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. |
| 117 | 450 mm x 300 mm size. |
| 118 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets. |
| 119 | Sink only. |
| 120 | 630mm x 550mm x 180mm. |
| 121 | Supplying, fitting and fixing Waste fittings complete. |
| 122 | Polythene. |
| 123 | 32 mm dia. |
| 124 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg sq.cm. (for water lines only). |
| 125 | 15 mm. |
| 126 | Supplying, fitting and fixing bib cock or stop cock. |
| 127 | Chromium plated Bib Cock short body (Equivelent to Code No.511 & Model- Tropical /sumthing special of ESSCO or Similar brand). |
| 128 | Supplying, fitting and fixing PVC pipes of approved make of of Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made seperately). |
| 129 | For Exposed Work PVC Pipes. |
| 130 | 50 mm. |
| 131 | Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc. |
| 132 | With 'P' trap (with vent). |
| 133 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. Specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc. |
| 134 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any foor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Enginer-in-charge) Payment will be made on centre line measurement of the total pipeline including specials.). |
| 135 | Underground. |
| 136 | 160 mm dia. |
| 137 | Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster work and artif |
| 138 | icial stone flooring is to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directon of Engineer-in-Charge. |
| 139 | For 30 users. |
| 140 | With Bazree (JSW/JSP/SHYAM /SRMB/BMASL/ELECTROSTEEL/SSL) |
| 141 | Constructing Inspection pit to a depth of 1.5 metre (inside), 250 mm thick 1st class brick work (1:4) in all sides over a layer of jhama brick soiling and 150 mm thick cement concrete with stone chips (1:3:6) including necessary earth work, fitting and fixing approved type S.W. master trap, constructing masonry invert with cement concrete (1:1.5:3) with stone chips, plastering inside and outside( outside upto 300 mm below G.L.) with 20 mm thick cement plastering (1:4) and neat cement punning, including, supplying, fitting and fixing one 560 mm dia. R.C.C. manhole cover of approved make with R.C.C slab of 100 mm thick with cement concrete (1:1.5:3) with stone chips including necessary rreinforcement(upto 1%) and shuttering and necessary corbelling brick work(1:4) so that the R.C.C. cover slab rests 150 mm above adjucent G.L., cement plaster(1:4) 10 mm thick on all external surfaces of the top slab as directed complete in all respect and remeval of surplus earth with all costs of labour |
| 142 | 900 mm X 750 mm(inside) chamber including fitting and fixing S.W. master trap of 150 mm dia. of approved make. |
| 143 | With Bazree (N.B.Variety).(SAIL/TATA/RINL) |
| 144 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work(6:1) band all round and cement brick work(6:1) upto 0.90 metre from top with 19 mm thick cement plastering(4:1) to inside face upto the depth of cement brick work, 12 mm thick cement plaster(4:1) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal(50 mm to 63 mm size) including R.C.C. cover slab of designed thickness with cement concrete(4:2:1) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making necessary arrangements for pipe conections, excavation of well including shoring, dewatering and remeving the excess earth from the premisis as per direction complete in all respect with all costs of labour and materials.W |
| 145 | (OTHER MANUFACTURES NOT SPECIFIED) |
| 146 | Dismantling carefully wood work in posts, post plates, rafters, partition etc. sorting and stacking serviceable materials at site and removing rubbish as directed. |
| 147 | (a) Cleaning the walls and ceiling by scraping, sand papring and smoothening down the surface including puttying. |
| 148 | Removing loose scales, blisters etc. from old painted surface and thoroughly smootherning the surface to make the same suitable for receiving fresh coat of paint. |
| 149 | Polyurethane Polishing to woodwork with required colour as approved byEngineer-in-Charge with preparing surface including scaffolding and hirecharges of compressor machine including cost of filler and hardenermaterial such as P. U. Sealing, P. U. Top coat (Matt/Glossy), Thinner,Spirit etc. and inclusive of all operation, material and labour complete asper direction of Engineer-in- Charge. |
| 150 | Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. |
| 151 | (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. |
| 152 | (b) Area of each tile the above 0.09Sq.m. |
| 153 | (ii) Other than Coloured decorative including white. |
| 154 | (B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. |
| 155 | (b) Area of each tile the above 0.09Sq.m. |
| 156 | (ii) Other than Coloured decorative including white. |
| 157 | Rendering the Surface of walls and ceiling with White Cement baseWATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 158 | Protective and decorative Acrylic exterior emulsion paint of approved quality , as per manufacture specification as per direction of EIC to be apply over Acrylic primer as required. the rate included cost of material , labour scaffoldic and all incidential charges but excluding the cost of primer.In ground floor ( two coat). |
| 159 | ( c) Super protective 100% Acrylic emulsion. |
| 160 | Rounding corners with cement mortar 1:3 for crack repairs. |
| 161 | Wood work in upper rails of railing , hand rail of staircase balcony etc. including necessary bend, moulding fitted and fixed complete ( for purpose of payment section will be measured in the square). |
| 162 | ( c) sishu, gamar, champ, Badam, Bhola, Morga, hallak. |
| 163 | Plain and finished timber planks in partition, shelves etc. fitted and fixed complete as per design (butt joints) in ground floor. |
| 164 | (i) 12 mm. thick planks. |
| 165 | (b) Sishu.champ,badam, gamar,bhola,mogra,hallak. |
| 166 | Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. |
| 167 | (ii) With 1:4 cement mortar . |
| 168 | (a) 20 mm.thick plaster. |
| 169 | (i) with 1:6 cement mortar. |
| 170 | (a) 25 mm. thick plaster. |
| 171 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals). |
| 172 | (f) sishu , Gamar, champ, badam, bhola, mogra, Hallak. |
| 173 | Glazed shutters of doors, window, fan light, clerestory windows etc. as per design (with ordinary glass of 7.4 kg./sq.m.,3 mm. thick) fitted with putty bed and teak wood bead and nails including fitting and fixing shutter in position but excluding the cost of hinges and other fittings , cost of glass , putty, wooden beads etc which will be paid separately.in ground floor. |
| 174 | (i) 40 mm. thick shutters. |
| 175 | (b) sishu,gamar,Champ,badam,bhola, mogra,Hallak, |
| 176 | supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). |
| 177 | (a) 40mm x 6mm, 250mm Length . |
| 178 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. |
| 179 | (v) 75 mm x 60 mm x 3.15 mm. |
| 180 | Iron catch hook of approved quality fitted and fixed to shutter and chowkat. |
| 181 | (b) 6 mm dia x 225 mm long. |
| 182 | Iron skeleton bolt of approved quality fitted and fixed complete. |
| 183 | (a) 375 mm long x 10 mm dia rod. |
| 184 | (iii) Steel body foot - door holder. |
| 185 | Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. |
| 186 | (iv) 150 mm long x 10 mm dia. bolt. |
| 187 | (iv) 150 mm long x 10 mm dia. bolt. |
| 188 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. |
| 189 | (a) With continuous plate base (hexagonal/round rod). |
| 190 | (ii) 100 mm grip x 10 mm dia rod . |
| 191 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. |
| 192 | (a) With continuous plate base (hexagonal/round rod). |
| 193 | (vii) 150 mm grip x 12 mm dia rod. |
| 194 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete (In all floors for internal wall & upto 6m height for external wall ). |
| 195 | (ii) 4 mm. thick. |
| 196 | Panel shutters of door and window, as per design (each panel consisting of single plank with out joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank, panel rate of reduction of 20% will be made). |
| 197 | (i) 50 mm.thick shutters with 25 mm. thick panel of size 30 to 45cm. |
| 198 | (a) 1st class best Indian teak. |
| 199 | (i) Brass floor door stopper. |
| 200 | (b) Priming one coat on timber or plastered surface with synthetic enamel oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 201 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. |
| 202 | (a) On timber or plastered surface: . |
| 203 | (1) With super gloss (hi-gloss). |
| 204 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. |
| 205 | (A) UPVC PIPES. |
| 206 | (ii) 110mm Dia. |
| 207 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806- 1957 & IS: 1161- 1958 connected to one another with bracket,gusset,cleats as per design, direction of Engineer-In-Charge complete including cutting to requisite size. fabrication with necessary metal arc welding conforming to IS: 816- 1956 & IS: 9595 using electrodes of approved make and brand conforming to IS: 814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section. consumables such as electrodes, gas and hire charges of all tools and plants and labour required for the work including all incidental charges such as electricity charges, labour insurance charges etc.(Payment to be made on the basis of calculated weight of structural tubular members as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with the weight of finished structural members. The rates are considere |
| 208 | (i) For trusses spanning up to 12.00 m. |
| 209 | Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150grams per sq. metre (followed by colour coated on both side) steel sheetwork having minimum yield strength of 550 Mpa of trapizoidal profile ofapproved make as per IS: 15965: 2012 and IS: 14246: 2013 (excludingthe supporting frame work) fitted and fixed with 55 mm & 25 mm selftapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc.complete with 150 mm end lap and one corrugation minimum side lap.(Payment to be made on area of finished work). In roof With .5mm thick sheet. |
| 210 | Galvanised iron sheet ridging fitted with necessary bolt, screws, washers etc complete. (225 mm end lapping). |
| 211 | (B) 450 mm laping each way. |
| 212 | (a) with 0.60 mm.thick sheet. |
| 213 | Galvanized iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm.M.S.flat bar clamps bent to design, bolts. Nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping). |
| 214 | (a) 225 mm. wide gutter. Please Enable Macros to View BoQ information |
