|
| 1 | Earth work in exacavation in trenches for foundations and for pipes cables etc. in ordinary soil (loam clay or sand) including lift upto 1.5 m and lead upto 30.0m including back filling, watering and ramming of excavated earth with disposal of surplus excavated earth with all cost of labour, T&P and as per direction of Engineer-In-Charge etc. complete |
| 2 | Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and all round the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along external perimeter of building, expansion joints, surrounding of pipes and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per I.S. 6313 part II 1981) Chloropyrophosnor any other approved material such Heptachlor or chlordance will be used the rate of application of chemical emulsion shall be as follows. (a) Treatment for masonry and foundation 6 litres per Sqm. |
| 3 | Laying Plain Cement Concrete in 1:4:8 mix (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) with mechanical mixing including all cost of cement bag, material, labour, T&P, and as per direction of Engineer-In-Charge etc. Complete in all respect. |
| 4 | Providing and fixing centering and shuttering for R.C.C work with labour, T&P and as per direction of Engineer-In-Charge etc. Complete |
| 5 | Laying R.C.C. in 1:1:2(M25) mix (1 cement :1 coarse sand 2.20 fineness modulus :2 graded Stone aggregate 20 mm nominal size) with mechanical mixing including its 12 mm dia bar fixing and binding with 24 BWG binding wire all cost of cement bag, material, labour, T&P, water arrangement above 1 km distance and as per direction of Engineer-In-Charge etc. Complete in all respect. |
| 6 | Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 Km. From the site of work and including watering, dressing etc. Rate to include cost of all materials labour T&P etc. required for proper completion of work. |
| 7 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 8 | Painting on D.P.C. with two coats of air blown bitumin 80/50 or 85/25 @ about 1.7 kg per sq. meter including cost of fuel if any. |
| 9 | Brick work with class M-105 bricks in 1:4 Cement mortar (1 cement :4 coarse sand of 2.20 fineness modulus) )with all cost of cement Bag, material, labour, T&P, water arrangement above 1 km distance and as per direction of Engineer-In-Charge etc. Complete in all respect. |
| 10 | Laying R.C.C. in 1:1:2(M25) mix (1 cement :1 coarse sand 2.20 fineness modulus :2 graded Stone aggregate 20 mm nominal size) with mechanical mixing including its 12 mm dia bar fixing and binding with 24 BWG binding wire all cost of cement bag, material, labour, T&P, water arrangement above 1 km distance and as per direction of Engineer-In-Charge etc. Complete in all respect. |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. |
| 12 | Providing and fixing 1mm thick M.S sheet door with Chaukhat and frame of 40×40×6 mm angle iron and 3 mm M.S gusset plates at the junction and corners all necessary fittings complete, including applying a priming coat af approved steel primer. Using M.S angles 40×40×6 mm for diagonal braces. |
| 13 | Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory window using galvanised M.S. wire gauge with avrage with of aperture 1.4 mm in both direction with wire of dia 0.63mm with second class teak wood beading 62x19 mm i/c all materials labour T&P etc |
| 14 | 12mm thick plaster on Brick Masonry with one part of cement and four parts of approved coarse sand including supply of all materials labour T&P and as per direction of Engineer-In-Charge etc complete in all respect |
| 15 | 6mm thick plaster on ceilling with one part of cement and three parts of approved coarse sand including supply of all materials labour T&P and as per direction of Engineer-In-Charge etc complete in all respect |
| 16 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 17 | White washing with lime to give an even shade |
| 18 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required,to achieve even shade and colour. |
| 19 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 20 | Supply and laying of vitrified floor tiles (Bell/Kajaria/Somani or Other Standard Make) in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colors and shades, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse Sand) including grouting the joints with white cement and matching pigments etc, complete (Size of Tile 60 X 60 CM) |
| 21 | Supplying and fixing 6 mm thick china glazed tiles of first quality in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and T&P etc. required for proper completion of the work.. |
| 22 | Supplying and fixing 80 mm thick precast cement concrete I shaped interlocking paver block a with top layer of 8 mm thickness manufactured from rubber moulds with compressive strength not less than 30 MPA (M-30) and weight 5 Kg per no with a 4 cm thick layer of sand in red colour with cost of all material, labour, T&P and as per direction of Engineer-In-Charge etc. Complete of work. |
| 23 | Provinding gola 75x75 mm in cement concrete1:2:4(1 cement:2coarse sand:4 stone aggreagate 10 mm and down gauge) including finishing with cement mortar1:3(1cement:3 fine sand) as per standered design in 75x75mm deep chase. |
| 24 | Making khurras45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4( 1 cement :2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C sheet 1mx1mx400micron finished with 12 mm cement plaster 1: 3 (1cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete. |
| 25 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 26 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 27 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 28 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 29 | Providing fixing white viterous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm size respectivrly with automatic flushing cistren with standarad flush pipe and C.P brass spreaders with brass unions and G.I clamps complete ,including painting of fitting and brackets ,cutting and making good the walls and floors wherever required. ) (one urinal basins with 5 litre white P.V.C automatic flushing cistern. |
| 30 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. |
| 31 | Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board. 510x1040 mm bowl depth 250 mm |
| 32 | Providing and fixing C.P. Brass shower rose with 15 or 20 mm inlet 100 mm diameter |
| 33 | Providing and fixing PTMT soap dish holder having length of 138 mm, breadth 102 mm height of 75 mm with concealed fitting arrangements,weighing not less than 106gms |
| 34 | Providing and fixing P.V.C waste pipe for sink or wash including P.V.C waste fittings complete . 32 mm dia/40 mm dia |
| 35 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 36 | Providing and fixing 15mm dia long nose C.P. brass bib cock of approved quality including all material, labour T&P etc. |
| 37 | Providing and fixing 15mm dia C.P.Brass stop cock of standard design and approved make i/c all materials labour T&P etc complete. |
| 38 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall |
| 39 | 20 mm nominal outer dia Pipes |
| 40 | 25 mm nominal outer dia Pipes |
| 41 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes |
| 42 | 110 mm diameter |
| 43 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 44 | Coupler:110mm |
| 45 | Bend 87.5°:110 mm bend |
| 46 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110mm |
| 47 | Providing and fixing soil, waste and vent pipes : |
| 48 | 100mm diameter |
| 49 | 75 mm diameter |
| 50 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ,IS :12701 maked ,with cover and suitable locking arrangemnt and making necessary holes for intel ,outlet and overflow pipes but without fittings and the base support for tank. |
| 51 | Providing & fixing electric wiring for light & fan point in conduite pipe with 1.5 sq mm pvc insulated copper wire in reccessed medium PVC conduit with piano type switch and suitable size MS box including cost of all material, labour, T&P etc for completion of the work. |
| 52 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 53 | Supplying of 1200mm sweep double ball bearing ceiling fan of approved make with all standard accessories suitable for 230v + 10% 3 phase supply etc. as required. (Polar, Usha, Khaitan, Bajaj, Crompton Greaves or as approved by Engineer-in-charge. |
| 54 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 55 | Supplying of 300mm dia 1400RPM 230 Volt, 50 Hz Single phase fresh Air exhaust fan decorative type with wind screen (Polar, Usha, Khaitan, Bajaj, Crompton Greaves or as approved by Engineer-in-charge. |
| 56 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep |
| 57 | Supplying and Fixing of 4feet Long LED tube light of 20 watt (Panasonic, Crompton, Havells) |
| 58 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 59 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 60 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 61 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : |
| 62 | Supply, fixing & installation of P.V.C wall panel 8mm thick with provision for providing switch board fixtures etc. Complete as per direction given by engineer-in-charge. Please Enable Macros to View BoQ information |
