|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 6 | Steel reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding all complete upto plinth level.Hot rolled deformed bars |
| 7 | Centering and shuttering including shuttering, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. |
| 8 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. Complete. 40 mm thick with 20 mm nominal size stone aggregate |
| 9 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 10 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead :With cement mortar 1:4(1 cement: 4 coarse sand). |
| 11 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 12 | 12 mm cement plaster of mix: 1:6 (1 cement : 6 fine sand) |
| 13 | Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge. |
| 14 | Providing and applying white cement based putty ofaverage thickness 1 mm, of approved brand andmanufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 15 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 16 | Brick work with Non modular fly ash brick confirming to IS : 12894 bricks of class designation 10 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 17 | Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand) |
| 18 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete |
| 19 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required said and colour complete to give and even said. Old work (one or more coats) |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. |
| 21 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface). |
| 22 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal Size). |
| 23 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below |
| 24 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 25 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hardwood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 26 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hardwood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary Screws |
| 27 | Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick |
| 28 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory Yvindows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 45x 70mm |
| 29 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250X16 mm |
| 30 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc.Complete : 150 X10 mm |
| 31 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. Complete :125 mm |
| 32 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less tha grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. Complete : 150 x10 mm |
| 33 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. Complete : 125 mm |
| 34 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. Complete : 250x16 mm |
| 35 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in – charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 36 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. |
| 37 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : White Vitreous China Orisssa pattern W.C. pan of size 580 x 440 mm with integral type foot rests |
| 38 | Providing and fixing White Vitreous China pedestal type water closet (European type W.C. pan ) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid |
| 39 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter |
| 40 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm |
| 41 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 42 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. Complete.110 mm |
| 43 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110X110X110 mm |
| 44 | Providing and fixing 10 cm PVC nahani trap with grating etc. Complete. |
| 45 | Providing,laying and fixing,jointing Eco drain 110 mm SN8 NuDrain Upvc pipes or of equivalent make,manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends,tees,coupler,etc,jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated material etc. Complete. |
| 46 | Providing, laying and fixing,jointing Eco drain 160 mm SN8 NuDrain Upvc pipes or of equivalent make,manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends,tees,coupler,etc,jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated material etc. Complete. |
| 47 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 470x420 mm bowl depth 178 mm |
| 48 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 49 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 50 | Providing andl aying matt finish ceramic tiles of having size 30cmx30cm confirmingto I.S.15622/2006(groupDIIA)and 7to8 mm thick for flooring in required position laid on abed of 1:4cement mortar including cementfloat,filling joint with white/colour cement slurry cleaning curing etc. complete |
| 51 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 52 | Providing and fixing plain lining with necessary screws/ nuts & bolts / nails, including a coat of approved primer on one face, and fixed on wooden / steel frame work , complete as per direction of Engineer incharge (frame work shall be paid for separately ). 12 mm thick commercial ply conforming to IS : 1328 BWR type. |
| 53 | Providing and fixing acrylic plastic sheet panels of approved quality in required thickness plain clear or any colour or obscured linings in lieu of glass pans to doors / windows including providing and fixing clips, putty etc. Complete . (b) 3 mm thick. |
| 54 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 55 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding |
| 56 | Finishing with Epoxy paint (Two or more coats ) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface ,etc. Complete. On concrete work |
| 57 | Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 58 | Providing 25 mm to 30 mm thick partition of polished black Kadappa stone slab of approved quality including giving required size & shape etc. Fixing in cement mortar 1:3 curing and cement etc. Complete. a) One side polish |
| 59 | structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 60 | Supplying of Ferric alum including transportation charges. |
| 61 | Supplying of Chlorine liquid including transportation charges. |
| 62 | Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of alllabour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. Complete. (Rate for all class of valves.) 50 mm |
| 63 | Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of alllabour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. Complete. (Rate for all class of valves.) 80 mm |
| 64 | Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of alllabour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. Complete. (Rate for all class of valves.) 100 mm |
| 65 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm diameter Class I |
| 66 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces |
| 67 | Providing and fixing pre coated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shapewherever required. |
| 68 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete1:4:8 mix (1 cement : 4 coarse sand (Zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement completeas per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 69 | Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of Class designation 7.5 |
| 70 | Providing, hoisting and fixing upto floor five level precast reinforced cement concrete in small lintels not exceeding 1.5m clear span upto floor five level including the cost of required centring, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 cement : 3 fine sand) on exposed surfaces but excluding the cost of reinforcement with 1:1.5:3(1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal-size). |
| 71 | Half brick masonry with fly ash bricks of class designation 10 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) |
| 72 | Neat cement punning. |
| 73 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, by mechinical / manual means ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: Pipes, cables etc, not exceeding 80 mm dia. But not exceeding 300mm dia |
| 74 | Providing and fixing bolts including nuts and washers Complete. |
| 75 | White washing with lime to give an even shade : Old work (two or more coats) |
| 76 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete:New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 pram/litre |
| 77 | Supply of Stainless Steel (SS304) Bib Cock, heavy duty, wall-mounted type, quarter-turn, with integrated flange, suitable for 15 mm nominal bore GI/PVC pipeline, with ceramic cartridge, including testing and ensuring leak proof performance, complete.complete in all respect as per the direction of Engineer-in-Charge. |
| 78 | Supply of Stainless Steel (SS304) Stop Cock of approved quality and make, heavy duty, quarter-turn operation with smooth ceramic cartridge, suitable for 15 mm nominal bore pipeline, including necessary fittings, testing and commissioning complete as directed.complete in all respect as per the direction of Engineer-in-Charge. |
| 79 | Supply of G.I. Union 15 mm nominal bore Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 80 | Supply of G.I. Union 20 mm nominal bore Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 81 | Supply of G.I. Union 25 mm nominal bore Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 82 | Supply of G.I. Union 50 mm nominal bore Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 83 | 15 mm nominal bore and 45 cm length PVC connection pipe with P.T.M.T. Nuts Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 84 | C.I. sluice valve (with caps) class I: 100 mm dia Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 85 | Supply of C.I. sluice valve (with caps) class I: 150 mm dia Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 86 | Supply of Vitreous china flat back wash basin 630x450 mm complete in all respect as per the direction of Engineer-in-Charge. |
| 87 | Supply of Vitreous China flat back wash basin 450*300 mm Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 88 | Supply of Vitreous china 10 litres low level cistern without fittings accessories Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 89 | Supply of Flexible (Coil shaped) Pvc waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm I/c Pvc waste pipe complete in all respect as per the direction of Engineer-in-Charge. |
| 90 | Supply of G.I Pipe 15 mm Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 91 | Supply of G.I Pipe 20 mm Including transportation loading, unloading and contractors profit all included.complete in all respect as per the direction of Engineer-in-Charge. |
| 92 | Supply of G.I Pipe 25 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 93 | Supply of G.I Pipe 50 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 94 | Supply of C.I. sluice valve (with caps) class I: 100 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 95 | Supply of C.I. sluice valve (with caps) class I: 150 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 96 | Supply of Stainless Steel (SS304) Waste Coupling, 32/40 mm size, heavy quality, chrome-finished, suitable for wash basins/sinks, including rubber washers, tightening, and leak-proof installation, complete.as per the direction of Engineer-in-Charge. |
| 97 | Supply of G.I Tee 15 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 98 | Supply of G.I Tee 20 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 99 | Supply of G.I Tee 25 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 100 | Supply of G.I. Tee 15 mm x 20mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 101 | Supply of G.I. Tee 15 mm x 25 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 102 | Supply of G.I. Tee 25 mm x 20 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 103 | Supply of G.I Elbow 15 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 104 | Supply of G.I Elbow 20 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 105 | Supply of G.I Elbow 25 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 106 | Supply of G.I Reducing Elbow 25 mm x 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 107 | Supply of G.I Reducing Elbow 20 mm x 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 108 | Supply of G.I Nipple 15 mm dia*6’’ Long Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 109 | Supply of G.I Nipple 20 mm dia *6’’ Long Including transportation loading, unloading and contractors profit all included. |
| 110 | Supply of G.I Nipple 25 mm dia *6’’ Long Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 111 | Supply of Mechanical joint 100 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 112 | Supply of Mechanical joint 150 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 113 | Supply of Mechanical joint 200 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 114 | Supply of Stainless Steel (SS304) Pillar Cock of approved design and quality, heavy duty, quarter-turn, suitable for mounting on wash basin/sink, with ceramic cartridge, including SS Pillar Cock of approved with flange and teflon tape all jointing materials, testing and making leakproof, complete.as per the direction of Engineer-in-Charge. |
| 115 | Supply of G.I Socket 50 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 116 | Supply of UPVC Pipe 15 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 117 | Supply of UPVC Pipe 20 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 118 | Supply of UPVC Pipe 25 mm dia Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 119 | supply of uPvc End cap Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 120 | supply of upvc brass MTA 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 121 | supply of upvc brass MTA 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 122 | supply of upvc FTA (thread) 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 123 | supply of upvc FTA (thread) 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 124 | supply of upvc brass FTA 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 125 | supply of upvc brass FTA 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 126 | supply of upvc Coupler 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 127 | supply of upvc Coupler 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 128 | supply of upvc Coupler 25 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 129 | supply of uPvc union 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 130 | supply of uPvc union 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 131 | supply of uPvc union 25 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 132 | supply of upvc tee 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 133 | supply of upvc tee 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 134 | supply of upvc tee 25 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 135 | Supply of upvc reducer 15*20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 136 | Supply of upvc reducer 20*25 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 137 | supply of upvc reducing Tee 25 mm*20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 138 | supply of upvc reducing Tee 20 mm*15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 139 | supply of upvc mta (thread) 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 140 | supply of upvc mta (thread) 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 141 | supply of pvc brass elbow 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 142 | supply of pvc brass elbow 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 143 | supply of Pvc elbow (thread) 15 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 144 | supply of Pvc elbow (thread) 20 mm Including transportation loading, unloading and contractors profit all included.as per the direction of Engineer-in-Charge. |
| 145 | Clearing wild grass/shrubs/vegetation/bushes up to 10cm girth by engaging brush cutter machine and removsl of rubbish upto a distance of 50mtrs. Outside the periphery of the cleared area. The cost is inclusive of hiring charges of machine POL. Operator, cutting tool and grass should be cut nearest to the ground level.surface area where ever brush cutter can not be used should also be cleared by engaging manpower etc. all complete as per instruction of Engineer in charge. |
| 146 | Brooming & cleaning of all roads in colony and within the premises of service building and other places as required with all tools & tackles such as brooms, ghamela etc. and stacking the garbage at specified place as per instruction of EIC. |
| 147 | Cleaning of common areas such as court yards, corridors, staircases, and surrounding of building including removal of dust dry leaves, little paper plastic waste and debris using proper tools to maintain good cleanliness standard etc. Also to dispose the rubbish up to 50 m also as per instruction of engineer in-charge. |
| 148 | Cleaning of all types of roof including removal of dry leaves, weedings and cleaning dram holes, brooming etc. all complete with tools & tackles such brooms & ghamela etc. and stacking the garbage at specified places as per instruction of EIC. |
| 149 | Tranpotation of rubbish/branches of trees by tractor trolly and unloading at designated place as per instruction of engineer in charge for lead upto 2.00km |
| 150 | Spraying of chemical-Ammonium salt of Glyphosate 71% SG to stop the growth of unwanted weeds and Gazer grass by taking appropriate safety measures as per Instruction of EIC. |
| 151 | Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into pit with adequate quantity of salt, lime bleaching power etc. and refilling the pit with earth all complete with tools, tackles and consumables as per instruction of EIC |
| 152 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
