|
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 3 | Disposal of moorum / building rubbish /malba/ similar unserviceable, dismantled or waste material bymechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead up to 10 km for all lifts, complete as per directions of Engineer-in-charge. Note- item to be applicable in urban area shaving directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand): 10 graded stone aggregate 40 mm nominal size) |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings,balconies and access platform |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing inpositionand binding all complete above plinth level. Mild steel and Medium Tensile steel bars |
| 8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 9 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) |
| 10 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 11 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) |
| 12 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugsor with dash fasteners of required dia & length ( hold fast lugsor dash fastener shall be paid for separately). Sal wood |
| 13 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately,all complete as per direction of Engineer-in charge. Second class teak wood. 35 mm thick shutters |
| 14 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 30 mm thick |
| 15 | Providing and fixing ISI marked, IS:1341, M.S. Heavy weight butt hinges with necessary screws etc. complete : 125x90x4.00 mm |
| 16 | Providing and fixing ISI marked oxidised M.S. Sliding door bolts with nuts and screws etc. complete : 250x16 mm |
| 17 | Providing and fixing ISI markedoxidised M.S. Tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm |
| 18 | Providing and fixing bright finished brass handles with screws etc. complete: 75 mm |
| 19 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete |
| 20 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m² |
| 21 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 22 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 23 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 24 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laidon 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Sixe of tiles 600X 600 mm . |
| 25 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 26 | Finishing wall wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, toachieve even shade and colour. |
| 27 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 28 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 29 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510 x 1040 mm bowl depth 225 |
| 30 | Providing and fixing P.V.C. Waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe. 32 mm dia |
| 31 | Providing and fixing G.I. Pipes complete with G.I. Fittings including trenching and refilling etc. 15 mm dia nominal bore |
| 32 | 20 mm dia nominal bore |
| 33 | 32 mm dia nominal bore |
| 34 | Making connection of G.I. Distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore |
| 35 | Fixing water meter and stop cock in G.I pipe line including cutting threading the pipe and making long screws etc. Complete (Cost of wtaer meter and stop cock to be paid separately. ) |
| 36 | Providing and fixing Polyethelene-Aluminium PolyethelenePE-AL- PE Composite Pressure Pipes conforming to IS- 15450, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to with stand temperature upto 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required)e.g. elbows, tees, reducers,couplers & connector setc.,with clamp sat 1.00 metre spacing. Thisincludesthecostsof cutting chases and including testing of joints complete as per direction of the engineer in charge.2025 (25 mm OD) pipe |
| 37 | 1620 (20 mm OD) pipe |
| 38 | 1216 (16 mm OD) pipe |
| 39 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral typefoot rests |
| 40 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings andbrackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 41 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 42 | Providingand fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore |
| 43 | Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality)complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 44 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore |
| 45 | Providing and fixing piller cock Jaguar or equivalent as per direction complete. |
| 46 | Providing and fixing Concealed stop cock with wall flage of opel prime no. CON083FTK Stop Cock PM Single control of jaguar or equvalent complete in all respect. |
| 47 | Providing and Fixing Soap dish stainless steel complate in all respect. |
| 48 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore |
| 49 | Providing and fixing Ployethelene - Aluminium- Ployethelene PE-AL-PE Composite tank, IS: 12701 marked, with cover and suitable locking arrangment and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank. |
| 50 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm nominal bore. |
| 51 | Providing and fixing high pressurre PVC spigot and socket, waste and ventilaying pipes ISI marked including fixing with approved adhesive etc. Complete. 150 mm |
| 52 | Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the well and floor etc. complete. 110 mm x90 mm |
| 53 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete 110 mm dia. |
| 54 | 75 mm dia |
| 55 | Providing and fixing PVC plain equal branch ISI marked including fixing with approved adhesive etc. complete 110 mm dia |
| 56 | 75 mm dia |
| 57 | Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete 110 mm dia |
| 58 | 75 mm dia |
| 59 | Providing and fixing PVC pipe 75 mm dia. |
| 60 | PVC 110 mm dia |
| 61 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Please Enable Macros to View BoQ information |
