|
| 1 | Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete (reinforcement cut as required to facilitate demolition) complete including removing debries ouside MD land all as specified and directed. |
| 2 | M & L for RCC type M-30 (using 20 mm graded stone aggregate) as in Chajjas complete all as specified and as directed |
| 3 | S & F TMT steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia but in stirrups. |
| 4 | All as per item No.03 above, but 6 to 8 mm dia bars. |
| 5 | Taking down chowkats or frames not exceeding 1.5sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified |
| 6 | Taking down chowkats or frames exceeding 1.5sqm but not exceeding 4sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified |
| 7 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge complete all as specified |
| 8 | S&F Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples all as specified. |
| 9 | S&F 4.8 mm thick Sheet glass,ordinary quality pin headed type and glazing with Aluminium snap beading with rubber Neoprene packing in square exc 0.5 sq. m in each pane complete all as specified and as directed. |
| 10 | S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers exc 1.5 sqm. |
| 11 | S&F fiber glass reinforced plastic (FRP) door frames of three legged of cross section 90 x 45 mm having single rebate of 32 x 15 mm to receive shutter of 30 mm thick. The laminate door frame moulded with fire retardent grade unsaturated polyster resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block of 2nd Class Hardwood in all the three legs. The frame shall be covered with fibre glass from all side M.S stay shall be provided at the bottom to sedy the frame complete as per direction of Engineer - in - Charge. |
| 12 | S&F 30 mm thick glass fiber reinforced plastics paneled door shutter of required colour & approved colour and manufactrures made with fire retardent grade unsaturated polister resin,moulded to 3mm thick FRP laminate for forming hollow rails & styles with wooden frame & suitable blocks of seasoned wood inside at required places for fixing of fittings along with MS tube frame of 19 gauge all around the styles & rails duly coated with steer primer cast monolithically with 5mm thick FRP laminate forpanels & conforming to IS:14856:2000 including fixing to frames. The shade & colour shall be approved by Engineer-in-Charge |
| 13 | S&F Plain solid, straight chowkats and frames of second class hard wood Wrought Framed rabatted on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 14 | M&L for Factory made 35 mm thick,2nd class hard wood (Hollock), gauged and skeleton shutters open rebated and prepared to receive gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified. |
| 15 | S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified. |
| 16 | S&F 300mm long (Length of Bolt in mm) Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified. |
| 17 | S&F 250mm long (Length of Bolt in mm) Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified. |
| 18 | S&F 200mm long (Length of Bolt in mm) Aluminium anodised,barrel tower bolts of extruded section and fixed all as specified and directed. |
| 19 | S&F 150mm (Size of Handle in mm) Extruded aluminium alloy handles, fabricated type,anodised all as specified. |
| 20 | S&F 100mm Butt hinges(Size of hinges in mm), medium weight, cold rolled, stainless steel, and fixed all as specified. |
| 21 | M&L for applying of silicon sealent in construction joint, window glass,polycarbonate sheets and required places to make joints water tights, after racking out of joints/cracks wherever necessary & throughtout cleaning at different level complete all as specified and as directed by Engineer-In-Charge. |
| 22 | S&F 12 mm thick toughened glass for door, partition etc. of any size and side portions of toughened glass fixed to wall / floor, joints sealed with clear silicon silicate gel to make water tight, edges with diamond cut including taper drilling to flush the screws / all fitting as required, floor hinges, patch fitting top, bottom and sides, lock and handles, spider joint etc. and floor door spring as per requirement all as specified, required at site by manufacturer instructions and complete all as specified and directed. |
| 23 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premisess complete all as specified and as directed |
| 24 | M&L for joint free non-skid ceramic tiles, coloured (of approved shade and design), 7 to 8mm thick, of superior quality, square / rectangular (area exceeding 0.18 Sqm but not exceeding 0.38 Sqm) joint free, as in floors, etc.set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match shade of tiles laid over & including 15mm thick screed bed in CM (1:4) complete all as specified and as directed |
| 25 | M&L for Light shade vitrified ceramic tiles, premium quality, coloured (of approved shade and design), 10mm thick, of superior quality, (square / rectangular) polished, area of each tiles not exceeding 0.36sqm,joint free, as in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles ,laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 26 | M&L for joint free Light shade vitrified ceramic tiles, premium quality, coloured (of approved shade and design), 10mm thick, of superior quality, (square / rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 sqm, as in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles ,laid over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed. |
| 27 | M&L for joint free Light shade vitrified ceramic tiles, premium quality, coloured (of approved shade and design), 10mm thick, of superior quality, (square / rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 sqm but vertical surfaces such as skirting, dados etcincluding screed bed layer 10mm thick in cement mortar 1:3 finished even and rough for receiving tiles on vertical surfaces complete all as specified. |
| 28 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons, compound wall etc.laid dry beded in any mortor complete all as specified. |
| 29 | M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms, floors and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite including grinding and polishing complete all as specified |
| 30 | Dismantling boarding, any description, fixed in any position with screws complete all as specified & directed by Engr-in-charge. |
| 31 | S&F anodised aluminium snap grid frame work for false ceiling all as specified complete all as specified & directed by Engr-in-charge. |
| 32 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for false ceiling snap grid of size 605 x 605 mm complete all as specified and directed by Engr in Charge. |
| 33 | S&F Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/curved surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh including any sunk or raised mouldings (fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and directed |
| 34 | M & L for wall care putty 3mm thk on Ceiling and applying two coats of oil bound distemper.all as specified directed by Engr in charge |
| 35 | Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 36 | Material and Labour for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth with out using extra cement complete all as specified and as directed. |
| 37 | M&L rendering 10 mm thick on fair faces of stone masonry surfaces or concrete surfaces on wall in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed . |
| 38 | Material and Labour for 5mm thick rendering on concrete surfaces in cement mortar 1:3 finished even and smooth with out using extra cement on ceiling complete all as specified and as directed. |
| 39 | M&L for preparation of new surface and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete as specified and directed. |
| 40 | M& L for preparation of newly plastered surfaces of wall and applying plaster of paris putty of 2 mm thickness over a one coat of primer on plastered surface and distempering two coats of 1st quality plastic emulsion paint of required shade and colour complete all as specified and directed |
| 41 | Material and labour for prepration of new surfaces of ceiling including cornicess plaster etc and applying two coat of oil bound distemper on ceiling complete all as specified and as directed. |
| 42 | Material and labour for complete removal of existing treatment surfaces of ceiling old surface and applying two coat of oil bound distemper on ceiling complete all as specified and as directed. |
| 43 | M&L for applying one coat of synthetic enamel paint on steel or iron surfaces of any decription, over 10 cm in width or grith, not othewise described including preparation of old painted surfaces complete all as specified and directed. |
| 44 | S&F 600x450 mm looking mirror 6-10mm tk wall mounted backlit (white and warm light & sensor button) of superior premium quality glass without frame with washers as in repair complete all as specified. |
| 45 | S&F in repair ceramic white / coloured (TABLE TOP) wash basin, scratch resistant, easy clean glaze, modern bathroom sink including cutting for and pinning in ends of brackets or erecting stand but inclusive of fixing of supply and waste pipe complete all as specified. |
| 46 | S&F in repair Vitreous China soap tray embedded in the wall complete all as specified. |
| 47 | S&F in repair Glass shelf assembly complete all as specified. |
| 48 | S&F 15mm bore pillar tap tall tower, (foam flow), table top basin tap, brass with chrome finished, screwed down high pressure, with lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, as in repair complete all as specified. |
| 49 | S&F in repairs Waste fittings,32 mm brass , chromium plated for glazed ware sinks , basins , etc. with long screwed shanks and fly -nuts , flange end bedded with waiste pipe in red lead cement and other end fixed complete all as specified and as directed. |
| 50 | S&F in repair, vitreous china wash down water closet pan complete type including flush tank, jet spray, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete complete all as specified and directed. MAKE - PRAYAG/CERA/EQUIVALENT |
| 51 | S&F in repair Bib taps, fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in bore of dia 15mm complete all as specified and as directed. |
| 52 | S&F in repair angle/stop valves, fancy type, chromium plated with long shank, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in bore of dia 15mm complete all as specified and as directed. |
| 53 | S&F in repair Health faucet, single function superior elite quality including long flexible tube, wall hook and making connections and fixed in position complete in all respect as specified |
| 54 | S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in bore of dia 15mm complete all as specified and as directed. |
| 55 | Demolition of brickwork or stone/boulders/block masonry, built in cement mortar including all quoins, arches, pillars, ashlar facing, dressed stonework, precast concrete artilcles and precast concrete block walling etc. complete all as specified and directed. |
| 56 | M&L Squared rubble walling with Porbandar stone masonary in CM 1:6 brought to courses, complete all as specified & directed by Engr-in-charge. |
| 57 | M& L for preparation of old plastered surfaces of wall by complete removal of existing treatment and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces to prepare the surface even and smooth of required shade and colour as per manufacturer's specification complete all as specified and directed. |
| 58 | M& L for factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: Stainless steel auto closing hinges/soft close clip on concealed hinges and aluminium sliding chaneels, S.S screws and necessary items required on site will not be paid separately. Rates are inclusive of all items required) |
| 59 | S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of nominal bore 110mm including dismantling of old pipe complete all as specified and directed |
| 60 | All as per item No.59 above but nominal bore 75mm |
| 61 | S&F in repair PVC (SWR) bends with cap any radius of nominal bore 110mm complete all as specified and directed |
| 62 | All as per item No.61 above but nominal bore 75mm |
| 63 | S&F in repair PVC (SWR) junction single, (Single T) equal or unequal of nominal bore 110mm complete all as specified and directed |
| 64 | All as per above item no.63 but nominal bore 75mm |
| 65 | M&L in replacement of point wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC nsulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required complete all as specified and as directed for the following:- |
| 66 | One light point control by one switch |
| 67 | One Ceiling fan/exhaust fan control by one switch |
| 68 | All as per item No.65 above but wire 2.5 sqmm One 3 pin 5 amp socket out point on the independent board |
| 69 | All as per item No.65 above but wire 2.5 sqmm One3 pin 5 amps socket out let point on same board with other switches. |
| 70 | All as per item No.65 above but for one socket outlet 15 amp on independent board with 4.0 Sq. mm cable and 4.0 Sq.mm. earth wire. |
| 71 | S & F in replacement Modular switch 1 way 6A, 1 module all as specified and directed by EIC. |
| 72 | S & F in replacement modular socket, Socket, 6A - 2/3 pin combined 2 module all as specified and directed by EIC. |
| 73 | S & F in replacement Socket 16A - 2/3 pin combined 2 module, all as specified and directed by EIC. |
| 74 | S & F in replacement Modular switch 1 way 16A, 1 module all as specified and directed by EIC. |
| 75 | S & F in replacement ceiling rose three terminal ll as specified and directed by EIC. |
| 76 | S & F in replacement Modular fan regulator120Watt, 2- module , AC 240 Volts complete. |
| 77 | S & F in replacement LED tube light fittings 4 feet 1x20 Watt ,220V, Indoor decorative LED Engineering Plastic batten with opal diffuser, IP 20 and with System Efficacy of 100lm/W ,holder including LED Tube light connecting up with 3 core flexible cppper conductor cable with sutable size from ceiling rose complete all as directed by Engr-In-Charge. |
| 78 | M&L in replacement of wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required for the following:- |
| 79 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire ( SPN Plug and Socket) |
| 80 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire (For Submain wiring SPN DB) |
| 81 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire (For TPN Plug socket) |
| 82 | S&F in replacement 8 way (4+24), TPN, vertical type, MCB DB double door |
| 83 | S&F in replacement 4 Pole MCCB 100 Amps 25 KA, Operational Voltage 690V |
| 84 | S&F in replacement 12 Way, SPN double door MCB DB |
| 85 | S&F in replacement 6A, to 32 A, ratings , SPN MCB, \\"C\\" curve, 10 KA breaking capacity |
| 86 | S&F in replacement 6 A, to 32 A, ratings , SP MCB, \\"C\\" curve, 10 KA breaking capacity |
| 87 | S&F in replacement 6 A, to 32 A, ratings , TPN MCB, \\"C\\" curve, 10 KA breaking capacity |
| 88 | S&F in replacement 6 A, to 32 A, ratings , TP MCB, \\"C\\" curve, 10 KA breaking capacity |
| 89 | S&F in replacement 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required |
| 90 | S&F in replacement 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A \\"C\\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required |
| 91 | S&F in replacement 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A \\"C\\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 92 | S&F in replacement XLPE insulated armoured and pvc sheated heavy duty electric cable , 3.5 core 50 sqmm aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts/wall/ceiling etc including testing complete all as specified and as directed. |
| 93 | S& F in replacement of laying of Double Walled Corrugated (DWC) HDPE pipe of following size 40/32 mm outer/inner dia of conforming to IS 16205 Part -24 including necessary bends,coupling ,tees, reducers, spacers,end caps, rubber rings etc having pressure rating not less than 450 N through trenches/wall/floor/on pole in any type of soil for protection of electric cable complete all as directed by Engr-In Charge |
| 94 | M&L in replacement Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to galvanized earth wire 4.00 mm dia by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal common salt ,Earthing lead 4.00mm dia up to 7.5m, 20mm dia medium grade GI watering pipe ,PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work complete all as specified and as directed |
| 95 | Taking down fan of any make/type/sweep,sealing cable end ,dismantling of blades and for repair /overhauling complete all as directed |
| 96 | M &L for Overhauling of ceiling fan /exhaust fan of any make and sweep after opening and cleaning rotor bearing and stator properly and oiling/greasing of bearing/ bushes,replacement of capacitor & reassmbling the same,& painting with similar colour ,fixing and connecting on its existing position and testing on completion all as specified and as directed . |
| 97 | M &L for Painting of ceiling fan/Exhaust Fan of any sweep complete including fan blade down rod with synthetic enamelled paint by spraying including cleaning and removing dust by polish paper and dirt and making smooth surface for painting ,filling cavities with filler |
| 98 | Fixing or hanging only ceiling fan after overhauling/repair of winding above and connecting up including provision of 3 core 1.5 Sqmm cable from ceiling rose or connector to fan( max up to 1m length) all as specified and directed Please Enable Macros to View BoQ information |
