Tender For Construction Of Commercial Complex In Scheme No. 7, Sector 7, Shastri Nagar, Meerut., Meerut-Uttar Pradesh

TDR : 56076876

Tender Notice
BOQ

22 Days Left

Meerut , Uttar Pradesh

Tender Brief : Tender For Construction Of Commercial Complex In Scheme No. 7, Sector 7, Shastri Nagar, Meerut.

Document Fees
₹ 8850 /-

EMD
Refer document

Tender Value
Refer document

Submission Date
17-07-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Civil WorkClearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
2	Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 mm width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
3	Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources)
4	Neat cement punning.
5	Providing & fixing of 1mm thick bituminious sheet (tar felt)as per engineer in charge
6	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing andreinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:.5.33 All works upto plinth level :5.33.1.1 Concrete of M25 grade with minimum cementcontent of 330 kg /cum
7	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing andreinforcement as per direction of the engineer-in-charge, for the following grades of concrete.:.5.33.2 All works above plinth level upto floor V level5.33.2.1 Concrete of M25 grade with minimum cementcontent of 330 kg /cum
8	5.33.2.2 Concrete of M30 grade with minimum cementcontent of 350 kg /cum
9	Centering,shuttering inluding strutting,proping etc. & removal of form for.Foundations, footings, bases of columns, etc. for mass concrete.
10	Suspended floors, roofs, landings, balconies and access platform.
11	Steel reinforcment for R.C.C work including strainghtening cutting bending placing in position & binding all complete up to plinth level. Thermo machanically treated bars of grade Fe-500D or more. (550)Same as above for ground floor
12	Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
13	Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of :(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) including applying of twice ( at base and top of mortar ) cement slurry @ 2.2kg/m2 (each time) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.
14	Half brick masonry with common burnt clay (non modular) bricks of class M- 150 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)
15	Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.
16	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part \|) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws(a) Single leaf
17	Fixing of Door, windows / ventilators chaukhats in position.(a) Door chaukhats
18	Fixing of Door, windows / ventilators chaukhats in position.(b) Window chaukhats
19	Fixing of Door, windows / ventilators chaukhats in position.(b) Ventilator chaukhats
20	12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
21	15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 coarse sand. (2.25FM)
22	Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to \|.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 11.46.2 Size of Tile 600x600 mm
23	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing of edges to give high gloss finish etc. complete at all levels.
24	Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : 11.19.1 Light shade pigment using white cement
25	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.
26	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
27	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :11.26.1 25 mm thick
28	Providing and laying integral cement based water proofing treatment (brick coba )including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water
29	Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
30	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding
31	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
32	Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture
33	Finishing walls with water proofing cement paint of required shade :13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm)
34	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr/10 sqm
35	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
36	Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm .
37	Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete(a) 200 mm x 10mm
38	Providing and fixing stainless steel handles with screws etc. complete (a) 125 mm
39	Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptableVentilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. 9.147.D1.1 Using R1 series with frame (33 mm & above )x (35 mm & above) & sash /mullion (33 mm & above) x (50 mm & above). (Height upto 0.90 metre).
40	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover
41	Providing and fixing ball bearing for rolling shutters.
42	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fastenersetc.).
43	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
44	Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T”runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips ofsize 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T,bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G \| sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.
45	Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather siliconesealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.
46	Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass finsand glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panelinside the SS channel shall be measured.
47	Supply and filling of cinder in sunken portion of toilet and roads as per direction of the engineer -in -charges including cartage and cost of materilas ,labour t&petc.required for proper completion of work.
48	Providing and laying water proofing treatment to vertical and horizontalsurfaces of depressed portions of W.C., kitchen and the likeconsisting of :(i) Ist course of applying cement slurry @ .488 kg/sqm mixed withwater proofing [email protected] kg/sqm conforming to IS 2645 in recommended proportions including rounding off junction of vertical andhorizontal surface.(ii) Second layer of slurry of cement @.242 kg/sqm mixed with water proofing cement compound @ .126 kg/sqm.This layer will be allowed to air cure for 4 hours .following with water curing for 48 hours .The rate includes preparation of surface treatment and sealing of all joints ,corners junction of pipes and masonry with polymer mixed slurry.
49	Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints.5.43.1 200 mm wide.
50	Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063).5.45.1 Wall Joint of 100 mm gap
51	Providing and filling in position, blown bitumen in expansion joints.
52	Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredSame as above but for European type W.C. pan with white plastic seat and lid.Make- Cera,Hindware.
53	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require a) White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap.
54	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board of size 510x1040x200mm
55	White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI marked
56	Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Felxible pipe a) 32mm dia
57	b) 40mm dia
58	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever requireda) One urinal basin with 5 litre white P.V.C. automatic flushing cistern
59	Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade
60	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
61	Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm nominal bore
62	Providing and fixing CP Brass 32 mm size Bottal Trap of approved quality & make and as per the direction of Enginer-in-charge.
63	Providing and fixing CP Brass Single lever telephonic wall mixture of quality & make and as per thedirection of Enginer-in-charge.a) 15mm dia nominal dia.
64	Providing and Fixing C.P. brass Ablution health faucet assembly with 1.0 m long braided PVC hose with mounting bracket fixed on wall complete.[FOR EWC]-Make-JAQUAR ALD-565
65	Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Fauct of approved quality conforming to IS:8931. 15 mm nominal bore-ESSCO SQT 526AKN
66	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893118.53.1 15 mm nominal bore
67	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78mm and effective height of 88 mm, weighing not less than 190gms.
68	Supplying & Fixing of CP soap tray fixed to the wall with PVC rubber plug with CP brass screws- Make-ESSCO AEC-1131
69	Supply and fixing of UPVC SWR Pipe type B conforming to IS-13592n including jointing the pipes with rubber ring, lubricant and UPVC SWR cuplar conforming to IS -14735. Also including excavation of trenches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before but excluding supply and cost of other fittings such as elbow, bead, Tee and Y-Tee including supply of all ,material labour and T&P required for proper completion of work.a) 110mm dia OD.
70	Supply and fixing of UPVC SWR Pipe type B conforming to IS-13592n including jointing the pipes with rubber ring, lubricant and UPVC SWR cuplar conforming to IS -14735. Also including excavation of trenches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before but excluding supply and cost of other fittings such as elbow, bead, Tee and Y-Tee including supply of all ,material labour and T&P required for proper completion of work.b) 90mm dia OD.
71	Supply and fixing of UPVC SWR Nahani trap size 100/75, 110/90mm conforming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125mm dia heavy duty C.P. brass jali.
72	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.a) 110mm
73	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.a) 110mm
74	Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms.
75	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.(internal work)Exposed on walla) 25mm dia nominal bore
76	b) 32mm dia nominal bore
77	c) 40mm dia nominal bore
78	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.Concealed work, including cutting chases and making good the walls etc.a) 15mm dia nominal bore
79	b) 20mm dia nominal bore
80	Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.a) 15mm nominal bore
81	Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 a) 15mm nominal bore
82	Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.a) 15mm nominal bore
83	Providing and fixing gun metal gate valve with wheel of approved quality.a) 20 mm dia nominal bore
84	Providing and fixing gun metal gate valve with wheel of approved quality.c) 32mm dia nominal bore
85	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats completea) 20 mm nominal bore
86	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats completeb) 25 mm nominal bore
87	Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.a) Pipes 80mm to 300mm diameter.
88	Supply and fixing of UPVC SWR Pipe type B conforming to IS-13592n including jointing the pipes with rubber ring, lubricant and UPVC SWR cuplar conforming to IS -14735. Also including excavation of trenches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before but excluding supply and cost of other fittings such as elbow, bead, Tee and Y-Tee including supply of all ,material labour and T&P required for proper completion of work.b) 160mm diameter
89	Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.a) 110mm diameter S.W.R. Pipe
90	Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.b) 160mm diameter S.W.R. Pipe
91	Providing and fixing UPVC S.W.R. Gully trap conforming to IS 14735 size 150x110 mm dia of self cleaning design including fixed with brick massonary chamber 250 x 250 x 250mm size I/C supply and fixing of C.I. cover with frame weight not less than 4.5 kg and C.I. grating 150x150mm coplete in all respect.
92	Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard designInside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With FPS bricks of class designation 75(i) For Sewer Line
93	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard designWith 20x20 mm square bar
94	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
95	15 mm cement plaster inside of septic tank of mix 1: 4 (1 cement : 4 coarse sand)
96	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate
97	Making Soak pit 1.25m diameter 2.5 mt depth including excavation disposal of surplus earth refilling it with coarse aggregateand RCC slab on top 1 :2 :4 with 450mm dia manhole cover and frame complete as required as per the standard design. DSR-19.32.1
98	Providing & fixing 75 mm dia vent pipes. [DSR 17.35.2.1]
99	M-150 brick work in 1:6 cement and corse sand of 2.25 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of the work.
100	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80mm thick cement concrete paver block of M-30 grade with approved colour, design & pattern.
101	Brick work with common burnt clay (non modular) bricks of class-150 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
102	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 23.1.1 All types of soil300 MM dia
103	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.300 MM dia
104	Supply , assembing , lowering and fixing in vertical position in bore well ERW (Electric Resistance welded ) FE 410 mild steel screwed and socket /plain ended casting pipe of required dia, conforming to IS: 4270, of reputed & approved make including painted with out side surface with two coats of anticorrosive including required hire and labour charges , fitting & accessories etc. all complete , for all depths as per direction of Engineer-in-charge. 100 mm nominal size dia having minimum wall thickness5.00 mm
105	Supply , assembing , lowering and fixing in vertical position in bore well ERW (Electric Resistance welded ) FE 410 mild steel screwed and socket /plain ended casting pipe of required dia, conforming to IS: 4270, of reputed & approved make including painted with out side surface with two coats of anticorrosive including required hire and labour charges , fitting & accessories etc. all complete , for all depths as per direction of Engineer-in-charge. 150 mm nominal size dia
106	Supplying , filling , spreading & leveling coarse sand of size range 1.5mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts,all complete , for all depths as per direction of Engineer-in-charge. Development of tube well in accordance with IS: 11189, to establish maximum rate of usable water yield without sand content , with required capicity air compressor , running the compressor for required time till well is fully developed , measuring static level & draw down etc. by step draw down method , collecting water sample & getting tested in approved laboratory , i/c/ disinfection of tubewell, all complete, including hire & labour charges of air compressor , tools & accessories etc. all as per requirement and direction of Engineer-in-charge.
107	Development of tube well in accordance with IS: 11189, to establish maximum rate of usable water yield without sand content , with required capicity air compressor , running the compressor for required time till well is fully developed , measuring static level & draw down etc. by step draw down method , collecting water sample & getting tested in approved laboratory , i/c/ disinfection of tubewell, all complete, including hire & labour charges of air compressor , tools & accessories etc. all as per requirement and direction of Engineer-in-charge.
108	Providing and fixing suitable size threaded mild steel cap or spot weldedplate to the top of bore well housing / casing pipe ,removable as per requirement ,all complete for borewell of . 150 mm nominal size dia
109	Providing and fixing M.S. clamp of required dia to top of housing / casing pipe , of tubewell as per IS:2800 (PART-1) ,including necessary bolts & nuts f required size complete 100 mm nominal size dia
110	Providing and fixing M.S. clamp of required dia to top of housing / casing pipe , of tubewell as per IS:2800 (PART-1) ,including necessary bolts & nuts f required size complete 150 mm nominal size dia
111	Providing and fixing Bail plug /Bottam plug of required dia to the bottam of pipe assembly of tubewell as per IS:2800 (PART-1)150 mm nominal size dia
112	Supply of 7.5 HP KSB make submersible pump set model BPD 302/4+UAMI 150/6/22-203 (S/D) suitable for tube well capable of pumping clear and cold water free from chemical and directly coupled with KSB electric moter operating of 415 volt suitable for 3 phase 50 cycle A.C. Supply of following duty condition 7.5 HP 6 stage pipe.A - Discharge of water in LPM 860 Approx size of discharge outlet in 80 mm.
113	Water supply tanker of 5000 litre capicity for boring
114	Supply and fixing of nylon jali around the slotted pipes complete as required.
115	Providing and fixing C.I. sluice valve . 100 mm nominal bore. Class I100 mm nominal bore. Class I
116	Providing and fixing G.I. pipes complete with G.I. fittings including trenchingand refilling etc.Submerssible to OHT80 mm dia nominal bore
117	Providing and lowering G.I. pipes complete with G.I. fittings including trenchingand refilling etc.50 mm dia nominal bore
118	Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge ,complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.35 sq. mm 3-1/2 core
119	Reinforcement cement concrete work in beam,suspended floors,roof having slope up to 5% andings,balconies,shelves,chajjas,lintels,bands,plain windows sills,stair case & sprial stair case above plinth up to floor five level excluding the cost of centering,shuttering,finishing & reinforcement with 1:1.5:3 (1 cement,1.2 coarse sand zone-iii,3 graded stone aggregate 20mm. (Nominal size)5.3
120	Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter
121	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia
122	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
123	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
124	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.
125	Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 150mm diameter S.W. Pipe
126	Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.b) 200mm diameter S.W. Pipe
127	Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) upto haunches of S.W. Pipes including bed concrete as per standard design.a) 150mm diameter S.W. Pipe
128	Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) upto haunches of S.W. Pipes including bed concrete as per standard design.b) 200mm diameter S.W. Pipe
129	Constructing brick masonry INSPECTION chamber 60x60x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including CI cover with frame LIGHT WEIGHT complete as per design. With FPS bricks
130	Centering,shuttering inluding strutting,proping etc. & removal of form for.Lintels, beams, plinth beams, girders, bressumers and cantilevers.
131	Centering,shuttering inluding strutting,proping etc. & removal of form for.Columns, Pillars, Piers, Abutments, Posts and Struts.
132	Providing and laying in position specfied grade of reinforcement cement concrete, excluding the cost of centering,shuttering,finishing & reinforcement. All work up to plinth level.1:1.5:3 (1 cement,1.2 coarse sand zone-iii,3 graded stone aggregate 20mm. (Nominal size)
133	Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
134	Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.
135	Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
136	Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).
137	Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 2nd class teak wood beading 62X19 mm
138	Fixing of Door, windows / ventilators chaukhats in position.(a) Door chaukhats
139	Fixing of Door, windows / ventilators chaukhats in position.(b) Window chaukhats
140	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
141	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to matchthe shade of the slabs, including rubbing and polishing complete.
142	Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm.
143	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250 mm x 10mm
144	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm.
145	Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer
146	Providing & fixing panes of glass with equal or equivalent I.S.I marked quality putty. Brads and springs and including supply of all materials and labour etc complete . 3.8 to 4.7 mm thick
147	Providing and fixing glass strips of 4.00 mm (1/8\\") thickness in joints of floor and skirting at the time of laying labour, tools and plants etc. complete of 3.5 cm. depth
148	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter
149	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend
150	Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge
151	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 60 cm dia, and 60 cm deep
152	Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.
153	Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge.
154	Ficus Nuda Topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180to 210cm ht in 40 cm Cement Pot
155	Providing and Displaying Ficus black vivion piller Topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.
156	Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.
157	Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge.
158	Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.
159	Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.
160	Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot,
161	Making drain along apron .150X150MM
162	Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar
163	Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
164	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below
165	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm
166	CARRIAGE OF MATERIALS By Mechanical Transport including loading,unloading and stacking Lime, moorum, building rubbish
167	Scrap Value of Brick, Steel, Grill Window etc. as per direction of Engineer - in- charge.
168	COST OF BARRICADING GATE as per direction of Engineer - in- charge.
169	INTERNAL ELECTRIFICATION WORKWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed) Group C
170	Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
171	Wiring for light/ power plug with 2X4 sq. mmFRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. (Make: As Approved in U.P.P.W.D List Enclosed)
172	Wiring for light/ power plug with 4X4 sq. mmFRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. (Make: As Approved in U.P.P.W.D List Enclosed)
173	Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Make: As Approved in U.P.P.W.D List Enclosed)2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
174	2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
175	4 X 10 sq. mm + 2 X 10 sq. mm earth wire
176	4 X 16 sq. mm + 2 X 6 sq. mm earth wire
177	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Make: As Approved in U.P.P.W.D List Enclosed)25 mm
178	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)5/6 A switch
179	2 way 5/6 A switch
180	15/16 A switch
181	3 pin 5/6 A socket outlet
182	6 pin 15/16 A socket outlet
183	Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
184	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
185	Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
186	3 Module (100mmX75mm)
187	4 Module (125mmX75mm)
188	6 Module (200mmX75mm)
189	8 Module (125mmX125mm)
190	Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module
191	3 Module
192	4 Module
193	6 Module
194	8 Module
195	Installation, Testing and Commissioning of pre-wired, fluorescent fitting / compact fluorescent/ LED fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS/HFFR PVC insulated, copperconductor, single core cable and earthing etc. asrequired. (Make: As Approved in U.P.P.W.D List Enclosed)
196	Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS/HFFR PVC insulated, copper conductor, single core cable etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
197	Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.
198	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)Upto 450 mm sweep
199	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed) Group C
200	MCCB, MCB & DB'SProviding and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)100 A,30KA,FPMCCB
201	125 A,36KA,FPMCCB
202	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (Make: As Approved in U.P.P.W.D List Enclosed)6 way , Double door
203	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). (Make: As Approved in U.P.P.W.D List Enclosed)4 way (4 + 12), Double door
204	6 way (4 + 18), Double door
205	Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) (Make: As Approved in U.P.P.W.D List Enclosed)4 way (4 + 12), Double door
206	8 way (4 + 24), Double door
207	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)Single pole
208	Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
209	Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)40 A
210	Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
211	Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required. (Make: As Approved in U.P.P.W.D List Enclosed)
212	Supplying and installaton following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required. (Make: As Approved in U.P.P.W.D List Enclosed)100 mm width X 50 mm depth X 1.6 mm thickness
213	150 mm width X 50 mm depth X 1.6 mm thickness
214	200 mm width X 50 mm depth X 1.6 mm thickness
215	300 mm width X 50 mm depth X 1.6 mm thickness
216	Supplying and installation following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required. (Make: As Approved in U.P.P.W.D List Enclosed)100 mm width X 50 mm depth X 1.6 mm thickness
217	150 mm width X 50 mm depth X 1.6 mm thickness
218	200 mm width X 50 mm depth X 1.6 mm thickness
219	300 mm width X 50 mm depth X 1.6 mm thickness
220	Supplying and installation following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastner etc as required. (Make: As Approved in U.P.P.W.D List Enclosed)100 mm width X 50 mm depth X 1.6 mm thickness
221	150 mm width X 50 mm depth X 1.6 mm thickness
222	200 mm width X 50 mm depth X 1.6 mm thickness
223	300 mm width X 50 mm depth X 1.6 mm thickness
224	EARTHINGEarthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. (Make: As Approved in U.P.P.W.D List Enclosed)
225	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.
226	Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.
227	Supplying and laying 6 SWG G.I. wire at 0.50 Meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
228	Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) (Make: As Approved in U.P.P.W.D List Enclosed)
229	Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) (Make: As Approved in U.P.P.W.D List Enclosed)
230	Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
231	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
232	Providing and laying earth connection from earthelectrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. (Make: As Approved in U.P.P.W.D List Enclosed)
233	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
234	CABLE SUPPLY AND LAYINGSupply of laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 volts grade. (Make: As Approved in U.P.P.W.D List Enclosed)10 sqmm 4 core
235	16 sqmm 4 core
236	25 sqmm 3.5 core
237	300 sqmm 3.5 core
238	185 sqmm 3.5 core
239	Laying of one number PVC insulated and PVCsheathed / XLPE power cable of 1.1 KV grade offollowing size in the existing RCC/ HUME/ METAL pipe as required. (Make: As Approved in U.P.P.W.D List Enclosed)Above 95 sq. mm and upto 185 sq. mm
240	Above 185 sq. mm and upto 400 sq. mm
241	Laying of one number PVC insulated and PVCsheathed / XLPE power cable of 1.1 KV grade offollowing size in the existing masonry open duct as required. (Make: As Approved in U.P.P.W.D List Enclosed)Above 95 sq. mm and upto 185 sq. mm
242	Above 185 sq. mm and upto 400 sq. mm
243	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. (Make: As Approved in U.P.P.W.D List Enclosed)Upto 35 sq. mm (clamped with 1mm thick saddle)
244	Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
245	Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)
246	Above 185 sq. mm and upto 400 sq. mm (clampedwith 40x3mm MS flat clamp)
247	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (Make: As Approved in U.P.P.W.D List Enclosed)3½ X 25 sq. mm (28mm)
248	3½ X 35 sq. mm (32mm)
249	3½ X 50 sq. mm (35mm)
250	3½ X 70 sq. mm (38mm)
251	3½ X 95 sq. mm (45mm)
252	3½ X 120 sq. mm (45mm)
253	3½ X 185 sq. mm (57mm)
254	3½ X 300 sq. mm (70mm)
255	4 X 16 sq. mm (28mm)
256	Supply and Fixing of 9 Mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 155 mm & Base plate 16 mm thick) having 3 mm thickness with single arm bracket length of 1 Mtr. length in 1:2:4 RCC foundation bolt including the Cost of Fundation, Excavation & Back Filling Required T & P complete in all resped. As per SOR Rate- 2024 [S.I. NO.-21.2.4] [Without GST Rate 30046.00 x 0.8475 = Rs. 25463.9 Say Rs. 25463.00 (Make: As Approved in U.P.P.W.D List Enclosed)
257	Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required (Make: As Approved in U.P.P.W.D List Enclosed)50 mm dia
258	80 mm dia
259	Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction. 185 sqmm 3.5 core
260	70 sqmm 3.5 core
261	35 sqmm 3.5 core
262	Supplying and fixing of Palm / pin type copper tin plated cables sockets (lugs) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of Engineer-Incharge.185 sqmm
263	70 sqmm 3.5 core
264	35 sqmm 3.5 core
265	LIGHT & FAN FIXTURESSupply and fixing of 12 Watt to 15 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. (Make: As Approved in U.P.P.W.D List Enclosed)
266	Supply and fixing of 12 Watt to 15 Watt indoor surface mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. (Make: As Approved in U.P.P.W.D List Enclosed)
267	Supply and fixing of LED Tube Light with Metal heavy duty Box type batten Light fitting 10 watt suitable for upto 15 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect. (Make: As Approved in U.P.P.W.D List Enclosed)
268	S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work.
269	Supply of Ceiling fan with fan motor of AC permanent insulation, capacitor rating conforming BEE 5 star rating and IS: 374/79 and also comply with IS:1709/1984 with latest amendment. The rated voltage 220/240 volt 50Hz, 1-ph AC the fan assemble should consist of down rod blades, shackle canopies etc and with double ball breaing system (Make: As Approved in U.P.P.W.D List Enclosed) BEE 5 star rated-1200 mm sweep
270	Supply of 14W LED Mirror light Similar to Crompton Greaves Cat Ref. LCL-14-CDL or equivalent.
271	Supply and erection of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required 300mm sweep.
272	WALL FANSupply of 400mm size Wall fan suitable for 230V, 50 Hz AC including modifying and connection with 3x1.5 sq mm FRLS copper conductor wire with PVC sleeve, loop earthing, making the good damage complete as required to do the job in all respect in accordance with laid specification or upto the satisfaction of engineer in charge.
273	TRANSFORMER 11000/0.433KVA 4Star Level-IIProviding, erecting, testing & commissioning approved make oil immersed naturally ONAN cooled, double wound, core type indoor /outdoor copper wound 11 kV/ 433 Volts Step Down Transformer of following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed system continuously rated for a full temperature rise in oil following capacities operating on 3 phase, 50 Hz 4 wire & neutral earthed and for a full temperature rise in oil not exceeding 50 deg. C at maximum ambient temp. Of 50 deg. C complete with necessary radiator first filling of new transformer oil & standard fitting as below complying with I.S. 1180 ( Part-II 2014) & 1981standards OFF load tap changing range steps -15% to 5% on H.V in steps of 1.25% .and L.V. for variation should be provided. The H.V. shall be connected delta & secondary with star connection. The transformer should have cable-end boxes on H.T. side & on L.T. side suitable for bus duct or cables as per requirement complete with test certificates from manufacturers. [MAKE :-ONLY THOSE MANUFACTURER WHOSE G.T.P. IS APPROVED IN PVVNL & HAVING VALID TYPE TEST BYCPRI/ERDA AND NOT BLACK LISTED WITHIN 7 YEARS IN P.V.V.N.L]1. Coservator with plain oil level gauge and oil drain plug 1nos.2. Top filter valve 1 Nos.3. Bottom filter-Cum-drain valave 1Nos.4. Rating and diagram plate 1nos.5. Earthing Terminals 2Nos.6. Thermometer pockets 1Nos.7. Lifting Lugs 2/4 Nos.8.Air release plug 2/4 Nos.9. Bi-directional rollers 4Nos.10.Jacking pads 1Nos.11.Presure relese valve 1Nos.12. Separate Bare LV neutral 433V 13. Detachable/Fixed type radiators 1Nos.14. Magnet Oil level gauge15. Oil temperature indicator 1Nos.16. Winding temperature indicator 1Nos.17. Marshlig Box single window 1No.18. Double flot buchholz's relaywith alarm and trip contact.800KVA
274	INDOOR TYPE (ONLY FOR SHOP) L.T. Panel Design Manufacture, supplying fixing in position, testing and commissioning of the following front operated cubicle type front access 2mm thick steel enclosed tree standing, dust and vermin proof, switch board with IP42 protection with hinged and lockable doors all switch boards shall have provision for Entry of cables from the Top or Bottom as required. (Make: As Approved in U.P.P.W.D List Enclosed) SWITCH BOARD-MAININCOMER2No. 1250A 4P 50KA ACB Electrically Operated Draw out Type Microprocessor Based O/L,S/C & E/F Release.BUSBAR:- 2000 A METERINGDigital VAF Meter with CTsPhase Indicating Lamp with ON/OFF/TRIP300 Amp TPN Aluminum busbar neutral busbar 100% capacity, maximum current density of 1.00Amp Per sq. mm.a. Busbar clearance phase to phase 32mmb. Busbar joints shall be thoroughly cleaned and a suitable oxiclizing grease shall be applied before making the joint.c. Busbar and main connection shall be marked color/ latter R,Y,B, Blackd. The busbar insulations shall be with heat shrinkable sleeve and PVC tape.e. Busbar supports shall be used padlocking facility shall be provide on all outgoing feeders doors and switch handle shall be lockable in off position.OUTGOING3No. 200 Amp TPN MCCB 415 Volt with Thermal Magnetic Release(1,2,3 NO, SHOP)4No. 100Amp 10KA TPN MCB 415 Volt C-CURVE(1 NO. LIFT)3 Spare
275	STREET LIGHT PANELSupply of Street Light Control Panel 40 Amp 4P MCB 10KA C-CURVE Phase Indicating Lamp
276	1no. 32amp MCB with 24hour calibrated time switch for automatic operation of the supply, auto/manual switch, 32amp TP Contractor for operation of the outgoing supply through the Time Switch and with 6no. 16amp TP 10Ka MCB’s as outgoing .The Feeder Pillar shall be mounted on a brick pedestal of suitable size 0.6m high complete as required. The Feeder Pillar shall be complete with all interconnections, busbar etc. complete as per design. (Make: As Approved in U.P.P.W.D List Enclosed)COMMON PANELDesign Manufacture, supplying fixing in position, testing and commissioning of the following front operated cubicle type front access 2mm thick steel enclosed tree standing, dust and vermin proof, switch board with IP42 protection with hinged and lockable doors all switch boards shall have provision for Entry of cables from the Top or Bottom as required. (Make: As Approved in U.P.P.W.D List Enclosed) 2No. 1250A 4P 50KA ACB Electrically Operated Draw out Type Microprocessor Based O/L,S/C & E/F Release.BUSBAR:- 2000 A METERINGDigital VAF Meter with CTsPhase Indicating Lamp with ON/OFF/TRIP300 Amp TPN Aluminum busbar neutral busbar 100% capacity, maximum current density of 1.00Amp Per sq. mm.a. Busbar clearance phase to phase 32mmb. Busbar joints shall be thoroughly cleaned and a suitable oxiclizing grease shall be applied before making the joint.c. Busbar and main connection shall be marked color/ latter R,Y,B, Blackd. The busbar insulations shall be with heat shrinkable sleeve and PVC tape.e. Busbar supports shall be used padlocking facility shall be provide on all outgoing feeders doors and switch handle shall be lockable in off position.OUTGOING1No. 630 Amp TPN MCCB 415 Volt with Thermal Magnetic Release(1,2,3 NO, SHOP)(125KVAR CAPACITOR)4No. 63A 4P 10KA MCB (LIFT)1NO. 32A TPMCB 10KA for pump1 No. 400A 4P 36KA MCCB ( second floor AC)1 No. 315A 4P 36KA VTPN DB ( Basement )4 No. 400A 4P 36KA MCCB VTPN DB ( LF, UF, FF, and SF)1 No. 100A 4P 36KA external light3 NO. Spare without MCB
277	SWITCH BOARD-METERING PANEL Design Manufacture, supplying fixing in position, testing and commissioning of the following front operated cubicle type front access 2mm thick steel enclosed tree standing, dust and vermin proof, switch board with IP42 protection with hinged and lockable doors all switch boards shall have provision for Entry of cables from the Top or Bottom as required. [MAKE :-ONLY THOSE MANUFACTURER WHOSE G.T.P. IS APPROVED IN PVVNL & HAVING VALID TYPE TEST BYCPRI/ERDA AND NOT BLACK LISTED WITHIN 7 YEARS IN P.V.V.N.L]INCOMER3No.200A 4P 50KA MCCB Electrically Operated Draw out Type Microprocessor Based O/L,S/C & E/F Release.BUSBAR:- 250 A METERINGDigital VAF Meter with CTsPhase Indicating Lamp with ON/OFF/TRIP300 Amp TPN Aluminum busbar neutral busbar 100% capacity, maximum current density of 1.00Amp Per sq. mm.a. Busbar clearance phase to phase 32mmb. Busbar joints shall be thoroughly cleaned and a suitable oxiclizing grease shall be applied before making the joint.c. Busbar and main connection shall be marked color/ latter R,Y,B, Blackd. The busbar insulations shall be with heat shrinkable sleeve and PVC tape.e. Busbar supports shall be used padlocking facility shall be provide on all outgoing feeders doors and switch handle shall be lockable in off position.OUTGOING40No. 32 Amp DP MCB 415 Volt with Thermal Magnetic Release
278	3 NO. Spare without MCBSUB-STATION WORKS:11KV H.T. PANEL FEEDER WORK11 KV H.T. VCB 1 Breaker Panel Board (Near Transformer)HT Panel, (Main) ( 1 INCOMING) (2 OUTGOING) Supply, erection, testing and commissioning of 1 panel, 630A ,11 kV, 3 Phase, 50 Hz., metal clad, dead front, 350 MVA rupturing capacity Vacuum Circuit Breaker One Incoming etc. complete with following in-comers including door interlocking panel should be expendable type complete as per technical specifications and as required.A. INCOMER :i) 1 No. VCB having following1 No. 630A, 11kV, 3 Phase, 50Hz., metal clad, dead front, 350 MVA rupturing capacity, Fully Drawout type, Vacuum Circuit Breaker (VCB)1 set of 11kV/110V Potential Transformers with HRC fuses1 Set of Phase indicating lamps with HRC fuses1 No. 0-15 kV Digital voltmeter with selector switch1 set of indicating lamps to indicate OPEN, CLOSE, TRIP,SPRING CHARGED, TRIP CIRCUIT HEALTHYPush button for ON, OFF,TRIP&TRIP circuit healthy1 set of 150/5-5A Current Transformer for metering and protectionDigital Ammeter with selector switch, Digital voltmeter with selector switch, Communicable type Digital Tri vector meter with RS485(a) 3 Over Current + 1 Earthing fault (50/51/50N/51N ) with built in trip circuit supervision function communication protocal with frunt RS-232 port for the local communication and rear RS-485 port for the remote communication. (b) Communicable type over voltage plus under voltage relay communication protocal with frunt RS-232 port for the local communication and rear RS-485 port for the remote communication. (c) Electromechanical type master trip relay.Digital frequency meter,Digital Tri vector meter.I Set of undervoltage relay and Overvoltage relayTrip circuit supervision relay,Auxiliary relays with shunt trip coilI No. Master Trip relay1 No. Digital Power factor meterControl voltage 24V DC.Operating mechanism Moterized cum mechanical.Panel space HeaterTNC Switch AccessariesPush button trip circuit healthy cheakPanel illumination lamp with switch.3 pin plug with socket of 15Amp.Local/Remote switchPower packet of 110V AC to 24V DCEmergency Trip ButtonMCB for AC & DCBUSBARS :11kV, 350 MVA, 800 Amps Three Phase busbars of copper
279	H.T./ Feeder work Supply and erection of double pole structure made of following types of support duly grouted in 1:4:8 cement concrete (1 cement, 4 coarse sand and 8 grit of 20mm nominal size plinthed plastered & painted in the same manner as already specified for respective supports suitable for plinth mounted type substation with different types of M.S. Channel and angle iron duly fabricated for disc insulator fittings, D.O. fuse set, TPMO ladder stand projecting outside, dropper and bracings , including cost of all material, labour and T & P required for proper completion of work as per drawing and direction of E/I. (as per specification no. 16)11 Mts. long 410 SP 55 S.T. Pole Bottom section Galvanised with base plate. As per Page No. (Make: As Approved in U.P.P.W.D List Enclosed)
280	Supply/laying of following type high conductivity aluminum strand compacted circular conductor XLP (E) armoured 11KV cable neutral earthed system confirming to IS 7098-Part-II(1985) with latest amendment at a depth of 1 Mtr. Below ground level over a cushion of 75mm thick sand around and protection with brick on sides, top of cable shall be properly connected with the earth conductor by clamps etc. with the cost of all material, labour, T&P etc. required for proper completion of the work.300 Sqmm 3 Core (Make: As Approved in U.P.P.W.D List Enclosed)
281	Supply & Making of folowing sizes Outdoor/indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as Required. [MAKE :-ONLY THOSE MANUFACTURER WHOSE G.T.P. IS APPROVED IN PVVNL & HAVING VALID TYPE TEST BYCPRI/ERDA AND NOT BLACK LISTED WITHIN 7 YEARS IN P.V.V.N.L] 300 Sqmm 3 Core indoor type as per DSR Rate- 2025 [S.I. NO.-23.4.4] [Without GST Rate 17414.00 x 0.755 x0.97 = Rs. 12753.14 Say Rs. 12753.00 (Make: As Approved in U.P.P.W.D List Enclosed)
282	300 Sqmm 3 Core Outdoor type DSR Rate- 2025 [S.I. NO.-23.5.4] [Without GST Rate 24255.00 x 0.755 x 0.97 = Rs. 17763.14 Say Rs. 17763.00
283	S/F of HDPE pipes (upto Pn 6kg pressure Rating material Grade PE 80, Nominal Dia (OD) 160mm 9.1mm thicknes for cable Complete in all respect as per relevants IS Technical Specification.
284	S/F of following type of G.I. pipe \\"B\\" class for cable clamped with supports by 3 Nos. clamps made of 50x6mm M.S. flat and suitable size of nut bolt and washer required for proper completion of work as per direction of E/I. As per Page No. 100 mm dia
285	Making suitable earth of H.T. overhead line pole with 2.5 Mts. long 20mm M.S rod connected with 7/16 SWG G.S. wire duly clamped & binded on pole including the cost of materials, labour and T & P required for proper completion of work as per direction of E/I.
286	S/F of danger board (H.T.) size 200x250 mm at suitable height of pole as per direction of E/I
287	S/F of barbed wire (1.5kg) duly clamped with 20x3mm M.S. flats at both ends on steel poles at suitable height as per direction of E/I.
288	Supply & Fixing of Cable Route Marker made of 1:2:4 R.C.C. Block size 1000x400x100 mm grouted with 1:3:6 cement stone grit coarse sand 30 cm below G.L. with painting numbering & marking etc. complete with all required material T&P etc. complete in all respects as per direction of E/I. (As per drawing attached)
289	S/F of .1.380M. long size 100x50mm straight M.S. channel with M.S. Clamp 75 x 10 mm M.S. Clamp for fixing up Pin Insulator Complete in all respect. As per direction of E/I.
290	Supply & Fixing of 2.24M long 65x65x6mm size straight M.S. Angle iron with held up 75 x 10 mm Clamp for fixing up H.T. Cable complete in all respects as per diredtion of E/I.
291	Supply & Fixing of 11 KV Pin Insulator with G.I. Pin complete in all respects as per diredtion of E/I.
292	DG SET 750 KVASupplying, Installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:(A) Diesel Engine:Tourbocharged Diesel engine 4 stroke water cooled, multi cylinder, dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 °C, 50% RH & at 1000 Meter MSL, capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per CPWD specifications.(B) Engine mounted Instrument Panel fitted with and having digital dis Plate for following:(i) Start-stop switch with key(ii) Water temperature indication(iii) Lubrication oil pressure indication(iv) Lubrication oil temperature indication(v) Battery charging indication and Voltage indication(vi) RPM indication(vii) Over speed indication(viii) Low lubricantion Oil trip indication(ix) Engine Running Hours indication(x) Fuel LevelUnit Rate 216Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)C) Alternator:Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 °C, 50% RH & at 1000 Meter MSL. The alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically balanced rotor, capable of taking 10% over loading for one hour after 12 hours of continuous operation, self cooled, self-excited and self-regulated through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for tropical conditions and with class- H insulation.(D) Base Frame & Foundation:Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.(E) FUEL TANK:Daily service fuel tank of suitable liters capacity as per CPWD Specifications, fabricated out of 3 mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C' pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications. (F) Exhaust System:Dry exhaust manifold with hospital type exhaust silencer and catalytic convertor. (G) Starting System:12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable numbers of batteries (180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside the acoustic enclosure of DG Set.D.C. voltmeter and ammeter, selector switch for trickle, off and boost and current adjustment. 9. Main supply failure monitor10. Supply failure timer11. Restoration timer12. Control unit with three impulse automatic engine start/stop and failure to start lockout. 13. Impulse counter with locking and reset facility.14. ON/OFF/Control circuit switch with indicator15. Audio/Video annunciation for(i) High water temperature(ii) Low lubricating oil pressure(iii) Engine over speed(iv) Engine fails to start(v) Full load/maximum load warning16. Protection for over/under Frequency, Loss of AC sensing, Over Current, Unbalancing load with suitable number of relays and accessories17. Maintenance notification based on Engine Run Hour & due date.18. Load Management through PLC to achieve auto opening and closing of incomer breakers, bus coupler switching of essential panel, interlocking providing signal to AMF Panel for load status and AMF shall give command to DG Set to auto start / auto stop depending upon load status and requirement etc. and necessary hardware and software required to perform the operation shall be provided by the contractor including all control wiring.750 KVA (Make: As Approved in U.P.P.W.D List Enclosed)
293	SOLAR PHOTO VATALIC POWER GENERATIONSupplying, installation, testing and commissioning of grid interactive roof top solar photo voltaic power generation system including space frame.(Make: As Approved in U.P.P.W.D List Enclosed)
294	FACAD LIGHT
295	Supplying Installation, Testing and Commissioning of Circular/ Rectangular/square LED RGB/ RGBWW/ RGBNW/RGBA/RGBW (as per site requirement) Facade Floodlight/ Projector luminaire for facade lighting with Pressure Die-cast aluminium housing, powder-coated finish, with inbuilt driver of following wattage as given below. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°, the scale shall be provided for rotation degrees. The luminaire shall be IP66 protection also having silicon gasket between optical cover & LED chamber to ensure proper IP66 protection and impact resistance of IK 07. CRI>80, SDCM<5, THD<10%. as per IEC 61000-3-2, under voltage, over voltage protection, driver inbuilt surge protection of 4KV and external surge protection (SPD) of 10 KV common mode/differential mode,Driver Efficiency>85%, EMI/EMC as per CISPR-15. There should be options of beam angles of 5/10/15/20/25/30/40/45/60 degree. Luminaire should have efficacy of minimum 35 lm/W for RGB/ RGBNW/ RGBWW/TNW and 65 lm/W for mono colour options. Luminaire shall be capable of producing dynamiccolour changing light for with 16 millioncolours by DMX/Ethernet based control. The beam angle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with replaceable driver and capable of operating at line voltage without any separate power supply from 100-270 V AC, 50 Hz with power factor > 0.9. Fixture shall be suitable to operate at an ambient temperature range of -10°C to +50°C. Lifetime of complete luminaire(LED ,Driver , Electrical & control circuitry) shall be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS: (IS 10322) with dully R Number marked and shall be complete with all necessary accessories required for proper working of fixture including connection/inter connection with weather proof ISI Marked copper conductor of minimum size 1.5sqmm connection cables and accessories, Integral male/female water proof connectors IP 68 etc. as required.The successful bidder shall submit the followingcertifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer, RoHS Compliance60 W (Make: As Approved in U.P.P.W.D List Enclosed)
296	100 W (Make: As Approved in U.P.P.W.D List Enclosed)
297	Supplying Installation, Testing and Commissioning of LED RGB/RGBWW/ RGBNW/ RGBA/RGBW suitable for exterior use having IP68 rating (as per site requirement). Flexible light strip of 5 mtr standard length with 12-15 Watt per meter. Luminaire shall be capable of producing dynamic colour changing light for with 16 million colours by DMX/Ethernet based control. Minimum System lumens 450 lumens/meter and System Lumen Efficacy > 30lm/w. Luminaire light beam spread - 100-110°, The Strip should have IP 68 protection and is offered IP 68 rated connectors to join the LED Strips in continuity. The luminaire must be offered with Aluminium channel for mounting the strip lights. The product should be complete with all accessories and Driver. Lifetime of complete luminaire (LED, Driver, Electrical & control circuitry) 100 DELHI SCHEDULE OF RATES (E&M)-2025 shall be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS (IS 10322) with dully R Number marked. Luminaire shall be complete with replaceable driver and capable of operating at line voltage without any separate power supply from 24 V DC, Fixture shall be suitable to operate at an ambient temperature range of -10°C to +50°C. The successful bidder shall submit the followingcertifications/reports for approval before supply of materials: product data sheets, LM79. report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance along with CE certificate.5 MTR
298	PUMPS(A) Supplying Installation , testing and commissioning of electric driven Main Fire Pump suitable for automatic operation and consisting of following , complete in all respects , as required: (B) Horizontal type ,centrifugal pump of cast iron body & bronze impeller with stainless steel shaft , mechanical seal conforming to IS 1520.(C) Suitable HP squirrel cage induction motor ,TEFC, synchronous speed 1500 RPM , suitable for operation on 415 volts, 3 phase 50HZ, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with class 'F' insulation,conforming to IS -325.(D) M.S. fabricated common base plate , coupling, coupling guard , foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered with anti vibration pads.2280 lpm at 70 m Head (Make: As Approved in U.P.P.W.D List Enclosed)
299	(A) Supplying Installation , testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following , complete in all respects , as required: (Diesel Driven Pump).(B) Horizontal type ,centrifugal pump of cast iron body & bronze impeller with stainless steel shaft , mechanical seal conforming to IS 1520.(C) Suitable HP , 1800 RPM water cooled with radiactor , diesel engine conforming to relevant IS standard complete with auto statring mechanism, 12/24 volts electric staring equipment, diesel tank , exhaust pipe extended upto 0.6 mm thick aluminium sheet cladding , residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in event of fault with audio indications, painted with post office red colour etc. as required. (D) M.S. fabricated common base plate , coupling, coupling guard , foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered with anti vibration pads.2280 lpm at 70 m Head (Make: As Approved in U.P.P.W.D List Enclosed)
300	(A) Supplying Installation , testing and commissioning of , complete in all respects , as required: (Jockey Pump).(B) Horizontal type ,centrifugal pump of cast iron body & bronze impeller with stainless steel shaft , mechanical seal conforming to IS 1520.(C) Suitable HP squirrel cage induction motor ,TEFC types suitable for operation on 415 volts, 3 phase 50HZ, AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with class 'F' insulation,conforming to IS -325.(D) M.S. fabricated common base plate , coupling, coupling guard , foundation bolts etc. as required.(E) Suitable cement concrete foundation duly plastered with anti vibration pads.180 lpm at 70 m Head (Make: As Approved in U.P.P.W.D List Enclosed)
301	(a) Supplying, installation, testing and commissioning of electric driven terrace pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in allrespects, as required: (Terrace Pump)(b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required.(c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-12615: 2018.(d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.(e) Suitable cement concrete foundation duly plastered and with anti vibration pads.900 lpm at 35 m Head (Make: As Approved in U.P.P.W.D List Enclosed)
302	CONTROL PANELSFabrication, supplying, Installation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised withhinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copperstrip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pumpset complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required : (Make: As Approved in U.P.P.W.D List Enclosed)Incomings400A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Ammeter (0-400 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF,trip indicating lamps
303	Set of Copper Bus Bar 500AOutgoings(Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps)Main Fire Pump200 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 75 hp pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation,selector switch for local/remote, auto/manual/OFF operation.Jockey Pump100 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.Diesel Engine ControlControl for diesel engine comprising -Automatic/Manual selctor switch & 3 attempt startingdevice, timers and relays as required, push buttons,start/stop in manual modeIndicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indicationBattery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0-20 A DC AmmeterAll standard relays and accessories for automatic operation of diesel engineSystem ControllerDesigning, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence asper specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications.Terrace Pump Starter Panel (Make: As Approved in U.P.P.W.D List Enclosed)
304	PIPES & ACCESSORIESPoviding laying , testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/3589 i/c fitting like elbow, tees, flanges,tapers, nuts bolts , gaskets etc. in ground including welding excavations & providing cement concrete blocks as supports , anticorrosive tratment with coltar / asphalt tape as pr IS 10221, refilling the trench etc. of following sizes complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)150 mm dia
305	Poviding laying , testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including welding ,fitting like elbow, tees, flanges,tapers, nuts bolts , gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint required shade complete as required : (Make: As Approved in U.P.P.W.D List Enclosed)25 mm dia
306	32 mm dia
307	40 mm dia
308	50 mm dia
309	65 mm dia
310	80 mm dia
311	100 mm dia
312	150 mm dia
313	200 mm dia (wall thickness 6.3 mm)
314	Supplying & fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Tpe- A) with blank Gunmetal/Stainless Steel cap and chain as required : (Make: As Approved in U.P.P.W.D List Enclosed)Single headed Stainless steel (External)
315	Single headed Stainless steel (Internal)
316	Supply and Installation weather proof lockable cabinet of size not less than 900X600X450 mm made out of 20gauge MS (as per BOQ) powder coated sheet of fully welded construction with hinged double front door partially glazed (3 mm glass panel).with locking arrangement, stove enamelled fire red paint (shade No. 536 of IS:5) including necessary locking arrangement and shall be painted with one coat of primer and two coats of synthetic enamel paint of approved shade. (External Cabinet).
317	Providing and fixing angle iron (40 mm x 40 mm x 5 mm) MS door frame with 16 G MS sheet, 900x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate.
318	Supplying ,fixing,testing and commissioning of butterfly valve of PN 1.6 rating ISI marked complete with ns, bolts, washers,gaskets conforming ti IS 13095 of following sizes as required : (Make: As Approved in U.P.P.W.D List Enclosed)65 mm dia
319	80 mm dia
320	100 mm dia
321	150 mm dia
322	Supplying ,fixing,testing and commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle , bronze/ gun metal seat, ISI marked complete with nuts, olts, washers,gaskets and conforming to IS 780 of following sizes as required : (Make: As Approved in U.P.P.W.D List Enclosed)100 mm dia
323	150 mm dia
324	200 mm dia
325	Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to educe pressure at the outlet to the level of 3.5kg/cm2 complete as required :
326	Providing , intalllation, testing and commissioning of non - return valve of following sizes complete with rubber gasket, GI bolts, nuts, washers etc. as required: (Make: As Approved in U.P.P.W.D List Enclosed)80 mm dia
327	100 mm dia
328	150 mm dia
329	Providing , intalllation, testing and commissioning of Y-strainer fabricated out of 1.6 mm thick stailnless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. (Make: As Approved in U.P.P.W.D List Enclosed)80 mm dia
330	100 mm dia
331	150 mm dia
332	200 mm dia
333	Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : (Make: As Approved in U.P.P.W.D List Enclosed)Stainless Steel (Grade 304)
334	Supplying and fixing first - aid Hose Reel with MS construction spray painted in post office red, conforming ti IS 884 complete with the following as required : (Make: As Approved in U.P.P.W.D List Enclosed)20 mm nominal internal dia water hose thermoplastic (Textile reinforced ) type-2 as per IS: 1258520 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipments on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. pipe and socket. 30 m
335	Supplying and fixing 63 mm dia, gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confoming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Stainless Steel (Grade 304)
336	Supplying and fixing of fire brigade connection of cat iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way -100 mm dia M.S. Pipe
337	4 way -150 mm dia M.S. Pipe
338	Supplying and fixing air vessel made of 250 mm dia , 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser , drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. (Make: As Approved in U.P.P.W.D List Enclosed)
339	Providing, fixing, testing and commissioning of Air vessel of 400mm dia for pressurization of fire system complete with valves at outlet / drain to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top, outside with one coat of primer & two coats of synthetic enamel paint of approved shade complete as required to operate commonly main fire pump, sprinkler pump & jockey pump at drop of pressure, automatically at required pressure setting. It should be complete as per manufacturer's specifications & as directed by Engineer- in-charge. working pressure:- 7 kg/sqcm test pressure: 10 kg/sqcm
340	Providing fixing, testing & commissioning of 15 mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : (Make: As Approved in U.P.P.W.D List Enclosed)Pendent Sprinkler
341	Horizontal side wall spirinkler
342	Providing fixing, testing & commissioning of adjustable type rossette plate.
343	Providing fixing, testing & commissioning of Foot Valve connection 200 mm
344	Providing, fixing, testing & commissioning of Air release valve with 15mm dia
345	Providing and fixing of pressure switch in M.S. pipe line including connection etc. as required :
346	Providing and fixing flow switch in following sizes pipe including connection etc. as required :(Make: As Approved in U.P.P.W.D List Enclosed)100 mm dia
347	Providing and fixingin position the industrial type pressure gauge with brass valve complete as required.
348	Providing fixing, testing & commissioning of installation control valve of cost iron body , brass/bronze working parts comprising of water motor alarm , bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates , pressure gauges, emergency releases , stainer, pressure switch, cock valve complete with drain valve and bypass , test control box, ball valves, MS pipe of required size, flanges,orifice plate, gasket etc of following sizes as required : (Make: As Approved in U.P.P.W.D List Enclosed) 100 mm dia
349	150 mm dia
350	Supplying , installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer , nipple, 2 side bracket, stockbar of following sizes complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)700 mm
351	1000 mm
352	1200 mm
353	Supplying , installation, testing & commissioning of deluge valve (to be used for water curtains) UL listed with wet pilot basic trim assembly for DVA with test and alarm, drip and drain valve with water motor gong complete as required . (Make: As Approved in U.P.P.W.D List Enclosed)80 mm dia
354	100 mm dia
355	Providing installation , testing & commissioning of welectric release trim assembly for deluge wall with two way solelnoid valve ,weather proof operation on 24 volts DC supply complete as required.
356	Supply, installation, testing and commissioningof ball valves with screwed ends confirming to IS 1703 -1977 with unions, etc.including all the necessary fixing materials complete.
357	Providing, fixing, testing & commissioning of resilient rubber bellows single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.5 Kg/cm2 and test pressure 14 Kg/cm2 to provide relief from stresses at pipe flanges. It should be complete as per manufacturer's specifications & as (Make: As Approved in U.P.P.W.D List Enclosed)80 mm dia
358	150 mm dia
359	200 mm dia
360	Supply and fixing of CO2 type Fire extinguisher 4.5kg. Capacity (ISI Marked is :15683)Complete with initial Charge and wall Bracked along with supply of all materials and labour for proper completion of work. (Make: As Approved in U.P.P.W.D List Enclosed)
361	Supply and fixing of Fire extinguisher ABC Type 6.00kg.Capacity (ISI Marked is :15683)Complete with initial Charge and wall Bracked along with supply of all materials and labour for proper completion of work. (Make: As Approved in U.P.P.W.D List Enclosed)
362	Intelligent Fire Alarm SystemSupplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories. The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. (Make: As Approved in U.P.P.W.D List Enclosed)Ten loop panel
363	Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
364	Supplying, installation, testing & commissioning of repeater panel wih 320 character display with inbuilt reset, acknowledge and silence switches complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
365	Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
366	Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. (Make: As Approved in U.P.P.W.D List Enclosed)
367	Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.
368	Supplying, installation, testing & commissioning of fault isolator complete with base as required. (Make: As Approved in U.P.P.W.D List Enclosed)
369	Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required. (Make: As Approved in U.P.P.W.D List Enclosed)
370	Supplying, installation, testing & commissioning of addressable fire control module complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
371	Supplying, installation, testing & commissioning of addressable manual call point complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
372	Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
373	Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
374	Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
375	Supplying, installation, testing & commissioning of fire telephone control panel. (Make: As Approved in U.P.P.W.D List Enclosed)
376	Cable & WiringSupplying & laying of 2 X1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. (Make: As Approved in U.P.P.W.D List Enclosed)
377	AIR CONDITIONING WORKSupplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 °C. The unit shall be suitable to work on 400V +/- 10%, 3Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building) (Make: As Approved in U.P.P.W.D List Enclosed) 20 HP 1 Nos 20 HP
378	16 HP 4 Nos. 64 HP
379	14 HP 2 Nos. 28 HP
380	10 HP 1 Nos 10 HP
381	Supply, installation, testing and commissioning of Ductable Unit Complete With all respect6.6 TR
382	8.00 TR
383	Corded RemoteSupply, Installation, testing & Commissioning of Cordeds Remote for various Indoor Units.
384	RefnetsSupplying, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUsIndoor Units
385	Outdoor Multi Joint
386	Refrigerant PipingSupplying & Installation of interconnecting following sizes of one end expanded refrigerant copper pipe work with Y-joints and Headers of following outer diameter, insulated with closed cell electrometric nitrile rubber tubular insulation between each set of indoor & outdoor units with outer mechanical protection of alluminum cladding for all exposed pipes as per specification all piping inside the room shall be propelrly fixed/supported with suitable size of clamp/ M.S. hanger and all external piping shall run in M.S. painted cable tray etc. as reqd. (The final refrigerant pipe sizes shall be as per manufacturer). (Make: As Approved in U.P.P.W.D List Enclosed)28.6 mm dia with 19mm thick insulation
387	22.2 mm dia with 19mm thick insulation
388	19.1 mm dia with 13mm thick insulation
389	15.9 mm dia with 13mm thick insulation
390	12.7 mm dia with 13mm thick insulation
391	9.5 mm dia with 13mm thick insulation
392	6.4 mm dia with 13mm thick insulation
393	Drain PipingProviding and fixing of PVC Piping complete with fittings, supports as per specifications and duly insulated with 6mm thick closed cell nitrile rubber insulation.40 mm dia with 13mm thick insulation
394	50 mm dia with 13mm thick insulation
395	Supply and charging of Refrigerant R-410A complete as required.
396	Charges for Cutting of wall and floors for Piping, Cables, etc.
397	SITC OF RCC/PCC Foundation for VRV/VRF Out door units.
398	Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hang-ers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Make GI Sheet: TATA/Jindal/SAIL.Thickness 0.63 mm sheet
399	Thickness 0.80 mm sheet
400	Supplying, Fixing, installation, testing and commissioning of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
401	Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete in confirmation to SMACNA/IS and as per specifications complete etc. as required. (Make: As Approved in U.P.P.W.D List Enclosed)
402	Supply, installation, testing and commissioning of Canvas Connection Complete With all respect
403	Supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell Nitrile rubber (Class \\"O\\") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The points shall be sealed with 50 mm wide and 3 mm thickself adhesive nitrile rubber tape insulation complete as per specifications and as required. 25mm
404	Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 50mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications.
405	E A R T H I N GEarthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
406	Providing and fixing G.I. tape 25 mm X 5 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
407	Electrical PanelMAIN LT PANELSupply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN ACB (65 KA, 4Pole Elect draw out, Micor processer Release IPR2) and TPN MCCB's (Four Pole 36 KA with thermal magnatic release) Switches and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses, current transormer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS:8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/ DMC support with detachable side covers and shall be suitable for extension on the sides. The switches entry boxes shall be complete with suitable cable end boxes reverse. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above Will be provided with Amp Metre, current transfonners and selector switches etc and insurtment fuse. The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6 mm/2mm. Cubicle type switch board shall be of cat A & B Only. (Make: As Approved in U.P.P.W.D List Enclosed)INCOMINGS1 Nos.320 Amp. 4P MCCB1 No. Voltmeter (digital type) with inbuilt VSS & control fuses 1 No. 0-500 Amp. Ammeter (digital type) Muilti function Meter400 Amps. TP&N Al bus bars OUT GOINGS:- 10 No. 63 amp. 4P, MCB 25KA
408	LT CABLESupply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by Engineer in charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (Make: As Approved in U.P.P.W.D List Enclosed)16 sq. mm 4 core
409	300 Sq.mm. 3.5 Core
410	Cu Cable (flexible Cable)2.5sq. mm 3 core
411	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.16 sq. mm 4 core
412	3½ X 300 sq. mm (82mm)
413	Cu Cable2.5sq. mm 3 core
414	Supplying and installing following size of perforated Hot Dipped Galvanized Iron Cable Tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5 % in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required.150 X 50 X 1.6 mm Thick
415	LIFT WORKSupply and Installation of 8 pax,1.00 mps [As per UPPWD Approved Make]
416	Supply and Installation of 16 pax,1.00 mps [As per UPPWD Approved Make]
417	CCTV WORKIP CAMERA 6MP FULL HD NETWORK IRMake: PRAMA, Model: PT-NC363P1-WNMS
418	IP CAMERA 6MP FULL HD NETWORK IR Make: PRAMA, Model: PT-NC360P1-WNMS
419	64CH NVR WITH 8 SATA SUPPORT UPTO 10TB EACH SATA PORT Make: PRAMA, Model: PT-NR3A64-M8/R
420	Hard Disk 10TB SATA (SAMSUNG/WD/SEAGATE
421	8-PORT PoE SWITCH WITH 2 UP-LINK GIGABIT TP-LINK/D-LINK
422	16-PORT PoE SWITCH GIGABIT WITH 2 UPLINK TP-LINK/D-LINK
423	24-Port ETHERNET SWITCH GIGABIT D-LINK/TP-LINK
424	4U RACK (DYNAMIC/DIGITAL ETC.)
425	9U RACK (DYNAMIC/DIGITAL ETC.)
426	UTP CAT6 CABLE (D-LINK/FINOLEX)
427	65’’ LED MONITOR LG/SAMSUNG
428	20/25mm PVC PIPE STANDRED
429	SERVICE :UTP CALE LAYING WITH/IN CONDUITE PIPE ON WALL/CABLE TREY/DUCT
430	CCTV CAMERA FIXING & INSTALLTION , CONFIGURATION OF 64 CH NVR ,MOUNTING OF RACK WITH SWITCH
431	MECHANICAL WORKSupply of Two Level Electro Mechanical Type Twin Stack Car Parking System accommodating 2 Cars Per Modules & in total 37 Modules accommodating 74 Cars with car Carrying Capacity of 2200 kg each and Car Dimension of 5000 mm length x 2000/1700/1550 mm height (SUV/Hatchback/Sedan) in Base level, 5000 mm length x 2000/1700/1550 mm height (SUV/Hatchback/Sedan) height above stack, with allowable car width of 2000 mm at each Level & average retrieval/parking time not more than 44 seconds. The Lifting speed should be @3 Meter/Minutes having Motor of1.5 Kw and having safety features as outlined in specifications and as under including cost of maintenance for one year during the Guarantee period:(a) Brakes : DC magnetic(b) Photo sensor(c) Emergency Switch in Operating(d) Wheel Stopper(e) Antenna Type Limit Switch(f) Antenna Type Limit Switch to Control Over Travel Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Commercial Complex In Scheme No. 7, Sector 7, Shastri Nagar, Meerut., Meerut-Uttar Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Commercial Complex In Scheme No. 7, Sector 7, Shastri Nagar, Meerut., Meerut-Uttar Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us