Tender For Redevelopment Of Saima Lodge At Gandacherra, Dhalai-Tripura

TDR : 56070613

Tender Notice
BOQ

30 Days Left

Dhalai , Tripura

Tender Brief : Tender For Redevelopment Of Saima Lodge At Gandacherra

Document Fees
₹ 20000 /-

EMD
₹ 3482000.0 /-

Tender Value
Refer document

Submission Date
20-07-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Bill No. I: Earthwork
2	Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.
3	Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. All kinds of soil
4	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.
5	Extra rates for quantities of works, executed:In or under water and/ or liquid mud, including pumping out water as required
6	In or under foul position, including pumping out water as required
7	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.All kinds of soil
8	Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.
9	Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/Lindane emulsifiable concentrate of 20%
10	Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion):Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
11	Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.With hlorpyriphos/Lindane E.C. 20% with 1% concentration.
12	Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
13	Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 fine sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
14	Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45° and plugging them with cement mortar 1:2 (1 cement: 2 fine sand) to the full depth of the hole: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
15	Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45° at 150 mm centre to centre and sealing the same.The work will be carried out as per IS: 6313 [Latest Revision].Under the Insecticides Rule 1971: 10(3A) any person who desires to undertake pest control operations will be a Licence holder. The agency must complying with all safety health and welfare regulations, appertaining to staff and work people employed on the site.Keeping the site free from debris arising from the works during the work and leave the site free from debris on completion of work to the satisfaction of the Owner.The agency shall give a 3-year service guarntee in writing supplemented by a seperate and unilateral guarantee from the specialised agency for the job to keep the building free of termites for the specified period at no extra cost of the Owner. SoR
16	Bill No. II: Cement Concrete Work
17	Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All Work upto Plinth Level1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size)
18	Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).DPC 40 mm thick
19	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of aproved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
20	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.
21	Bill No. III: Reinforced Cement Concrete Work
22	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All Work upto Plinth Level1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
23	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
24	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
25	Providing and laying in position design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge.(Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth levelReinforced cement concrete grade M-25 using 418 kg of cement per cum
26	Providing and laying in position design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge.(Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto Floor five levelReinforced cement concrete grade M-25 using 418 kg of cement per cum
27	Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of RMC from transit mixer to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth levelReinforced cement concrete grade M-25 using 418 kg of cement per cum
28	Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of RMC from transit mixer to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto Floor five levelReinforced cement concrete grade M-25 using 418 kg of cement per cum
29	Extra for providing richer mixes at all floor levels.Providing M-30 grade of concrete instead of M-25 grade of concrete B.M.C/R.M.C
30	Centering, Shuttering including struttings, propping etc and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork
31	Suspended floors, roofs, landings, balconies and access platform with timber planks
32	Suspended floors, roofs, landings, balconies and access platform with M.S. plates and props
33	Lintel beams, plinth beams, girders, bressumers & cantilevers with 12 mm shuttering ply
34	Columns, Pillars, Piers, Abutments, Posts and Struts with M.S. shutters
35	Stairs (excluding landings) except spiral-staircases with wooden plank
36	Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof: Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).
37	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more
38	Bill No. IV: Brick Work
39	First class brick work in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).
40	First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).
41	Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).
42	Bill No. V: Wood Work & PVC
43	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Karai wood
44	Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory/ windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge.Local Teak wood35 mm thick shutters
45	Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :125 mm
46	Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-In-Charge.Extruded section Profile size 48x40 mm.
47	Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS \\"U\\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter).
48	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge.
49	Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm dia.
50	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to openings /wooden frames with rawl plugs screws etc.
51	Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size)
52	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250 x 10 mm
53	200 x 10 mm
54	150 x 10 mm
55	Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm
56	100 mm
57	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper
58	Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality)
59	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:- 80xl.25mm M.S. laths with 1.25 mm thick top cover.
60	Providing and fixing ball bearing for rolling shutters (exceeding 10 sqm area) of approved make complete as required.
61	Extra for providing & fixing mechanical device chain and crank operation for operating rolling shutters of approved make complete as required:-Exceeding 10.00 sqm and upto 16.80 sqm in the area.
62	Extra for providing & fixing grilled rolling shutters manufactured out of 8 mm dia. M.S. plain bar instead of laths as per design approved by Engineer-in-charge (area of grill to be measured) complete as required.
63	Providing and fixing aluminium tubular handle bar of 32 mm outer dia, 3.0 mm thick and 2100 mm long with Stainless Steel screws etc. of approved quality complete as per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron.
64	Bill No. VI: Aluminium Work & Structural Glazing
65	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-For fixed portion of approved quality:-Powder coated aluminium ( minimum thickness of powder coating of 50 micron ).
66	For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-Powder coated aluminium ( minimum thickness of powder coating of 50 micron ).
67	Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (both primary and secondary sealant) of approved quality etc.complete as per specification, drawing and direction of Engineer-incharge
68	Filling the gap in between aluminium frame and adjacentRCC/brick work by providing weather silicon sealantover backer rod of approved quality etc. complete as perarchitectural drawing and direction of the Engineer-incharge:- (i) Upto 5 mm depth and 5 mm width.
69	Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron.
70	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
71	Bill No. VII: Flooring
72	Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles300 x 300mm in all shades and designs
73	600 mm x 600 mm in all shades and designs 1st class quality ceramic floor Porcelain tiles
74	Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.Double charged Stainfree vitrified tiles (Glossy)Size of tile 600 mm x 600 mm
75	Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.450 mm X 300 mm in all shades and design
76	Providing and laying flamed finish Granite stoneflooring in required design and patterns, in linearas well as curvilinear portions of the building allcomplete as per the architectural drawings withFlamed finish granite stone slab Jet Black, CherryRed, Elite Brown, Cat Eye or equivalent over 20mm (average) thick base of cement mortar 1:4 (1cement : 4 fine sand) laid and jointed with cementslurry and pointing with white cement slurryadmixed with pigment of matching shadeincluding rubbing, curing and polishing etc. allcomplete as specified and as directed by theEngineer-in-Charge-18 mm thick stone slab.
77	Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick, 1800mm length (minimum) and 130 mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded poly ethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bomboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, etc. all complete as per direction of Engineer-in-charge.
78	Providing and fixing coloured self adhesive PU - Tactile tiles, ground surface indicators (made of Polyurethane) grade 70/85 of size 300x300mm. for guiding/warning to the visualy impaired visitors in the entre/side of the pedestrian/ approch pathway as per design/specification and Harmonised guidelines complete in all respect as per the direction of the Engineer-in-charge.
79	Supply & installation of EPDM flooring
80	40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. Red sand stone
81	Bill No. VIII:ROOFING
82	Supply & installation of pre-painted Galvalume sheetsfor roofing/cladding (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) in550mpa steel grade, made out of Cold Rolled Steelcoated with Zinc-Aluminium alloy coating of 43.5% Zn,55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, topcoated of modified polyester of 20 micron, back sidecoat of 5 micron, having epoxy primer coat of 5 micronon both side. Sheet should have protective guard filmof 25 microns minimum to avoid scratches while transportation and should be supplied in singlelength upto 12 metre or as desired by Engineer-incharge.The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55mm) with EPDMwashers filled with white lead complete upto anypitch in horizontal/ vertical or curved surfacesexcluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever requiredand as per direction of Engineer-in-charge.0.80mm thickness
83	Supply & installation of pre-painted Galvalume sheetsroofing accessories in 550mpa steel steel grade, madeout of Cold rolled steel coated with Zinc-Aluminiumalloy coating of 43.5% Zn, 55% Al and 1.5% Siliconconfirming to AASTM A792/A792M and AS1397, Alloycoating AZ150/AZ70, colour coated with high qualitypolyester coating, top coated of modified polyester of 20micron, back side coat of 5 micron, having epoxy primercoat of 5 micron on both side etc. complete as perdirection of Engineer-in-charge. Sheet should haveprotective guard film of 25 microns minimum toavoid scratches while transportation. Sheet shouldhave protective guard film of 25 microns minimumto avoid scratches while transportation. The sheetshall be fixed using self drilling /self tapping screwswith EPDM washers complete forRidges/Valley/Gutter/Flashing of width 610mm:0.80mm thickness
84	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) asper IS : 277 and consisting of angle cleats of size 25 mmwide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mmdia bolts, other flange of cleat fixed to the angle hangers of25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips madeout of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall /partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for lightfittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board
85	Supply and Installation of Tensile Walkway Canopy in fabricated MS structureas as per specification and approval of Engineer-in-Charge
86	Bill No. IX: Steel Work
87	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes
88	Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required.
89	Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-In grating, frames, guard bar, railing, brackets, gates and similar works, all complete.In grating, frames, guard bar, railing, brackets, gates and similar works, all complete.
90	Bill No. X: Finishing Work
91	12 mm Cement PlasterCement mortar 1:4 (1 cement : 4 fine sand)
92	15 mm cement plaster on the rough side of single or half brick wall of mix:Cement mortar 1:4 (1 cement : 4 fine sand)
93	6 mm cement plaster of mix :Cement mortar 1:4 (1 cement : 4 fine sand)
94	Neat cement punning.
95	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
96	Distempering with 1st quality acrylic distemper (readymixed) having VOC content less than 50 grams/ litre, ofapproved brand and manufacture to give an even shade[Payment shall be made after submission of TestCertificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer.
97	Finishing walls with textured exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 3.28 litre/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm
98	Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface complete.Water thinnable cement primer
99	Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ).
100	Wall painting with acrylic plastic emulsion paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : Two or more coats on new work
101	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture
102	Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1800mm length (minimum) and 100 mm wide (minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of local teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded poly ethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bomboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, etc. all complete as per direction of Engineer-in-charge.
103	Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400 mm and length of 595 mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of ≥ 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical ‘T’ (for intermediates) / ‘L’(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2 mm/ 40x60x2 mm / 40x40x2 mm respectively, spaced at maximum spacing of 600 mm c/c matching to the tile vertical grid, and horizontal aluminium ‘C’-clamps of size 56x25x2 mm thickness of length 150 mm at junction of tiles and of length 75 mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400 mm c/c matching to the tile horizontal grid with two numbers of self-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers. The vertical ‘T’/’L/ Tubular’ sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304,M10 full threaded anchor fasteners with nylon sleeve 100 mm long (for brick work) and M8 expansion anchor fasteners 75 mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation. The brackets shall be of length 175 mm at junction of two vertical aluminium profiles and of length 100 mm at intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25 mm with EPDM washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends. The tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size which shall be inserted and pressed into position on the ‘C’ clamps holding the tiles and the cut-tiles shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. The vertical joint open groove between two adjacent tiles shall be 5 mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rain screen principle with provision for natural ventilation of the space between the façade tiles and the structural wall. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge. Note : Scaffolding wherever required to be paid separatelyWith 16 mm thickness (+/- 10%) terracotta tiles of grey colour
104	40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement motar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone.Red sand stone
105	Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and approved thickness fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-incharge and finished smooth including rubbing, curing etc. complete at all levels as required (measurement should be of exposed finished work):-White Agaria Marble Stone of approved shade of 18mm thick (75 x 50 cm).
106	Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size)
107	Bill No. XI: Dismantling & Demolishing
108	Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge:-Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
109	Demolishing reinforced cement concrete manually / by mechanical means including stacking of steel bars properly and disposal of unserviceable material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge.
110	Extra for cutting reinforcement in RCC or R.B. work manually / by mechanical means (payment to made on the cross sectional area of RCC or R.B. work) etc. complete as per direction of the Engineer- in-charge.
111	Extra for scrapping, cleaning and straightening reinforcement obtained from RCC or R.B. work etc. complete as per direction of the Engineer- in-charge.
112	Demolishing brick work including stacking of serviceable materials and disposal of unserviceable materials with all lifts and upto a lead of 50m etc. complete as per direction of the Engineer- in-charge:-In cement mortar
113	Removing mortar from brick and cleaning bricks including stacking bricks and disposal rubbish with all lifts and upto a lead of 50 m etc. complete as per direction of the Engineer- in-charge:-In cement mortar
114	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sqm and below
115	Of area beyond 3 sqm
116	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For Thickness of tiles 10 mm to 25 mm
117	Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of:T or L iron pipe
118	Dismantling steel work in built up section in channels, angles, tees, flats including all gusset plates, bolts, nuts, cutting rivets, welding including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc. complete as per direction of the Engineer- in-charge.
119	Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
120	Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.
121	Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge.
122	Bill No. XII: Swimming Pool
123	Supply, Installation, Testing and Commissioning of following Mechanical, Electrical and Plumbing Equipments and other miscellaneous items for Swimming PoolFilters:Bobbin Wound Horizontal filter,1200mm diameter. Filtration velocity 30m³/hr/m². Max. working pressure : 2.5 kg/cm². Flow rate : 59m³/hr. Outlet: 140mm. Filter Length-1900mm, a) Maximum operatin temperature 50 degree centigrade.b) Comply with European standards for pressure vessels 97/23/CE included in section 3 of article 3. c) Hydraulic pressure test 1.50 times the maximum admissible pressure.d) Resistance and thickness calculations are basd on norms BS-4994 and AD merkblatt N1.e) characterisctics of internal components as follows: - i) internal components and pipe in PVC. ii) PP laterls with 0.30 Slots. iii) Bolts, nuts and washers is AISI-316 iv) EPDM seals and gaskets complete all as specified and Filters are designated official products of FINA with certificate
124	Active Clear Glass Media• More efficient and environmentally friendly filtration.• Greater filtration capacity.• Water and energy savings.• Cleaner filter bed as bacteria does not remain trapped and fewer chemical products are needed
125	Valve BatterySupply, Installation, Testing & Commissioning of Valve Battery Manifold made in PVC with flanges for connecting to filters as per DIN 2501 standards. Consists of set of 5 - buttterfly valves for carrying out filtration, back-washing, rinsing and shut down of the filters .etc., complete . Size : 140mm. DIN-2501 standard.
126	Valve Battery Supports:Supply, Installation, Testing & Commissioning of Valve battery supports made in Zinc Plated Steel ..etc., complete , Height : 2.30m
127	Support Brackets 2 Support Brackets with anti-vortex clamps and fixing screws
128	Re-circulating Pumps Supply, Installation, Testing & Commissioning of Cast Iron Pumps 3000 r.p.m. Mechanical Seal in Stainless Steel. I.P.-54 motor protection. Stainless steel AISI-420 shaft with stainless steel AISI-316 strainer basket. Conn. PN-16 according to DIN2501. Flowrate : 60m3/h @ 12m.head. 5.5 HP Voltage 400V/ 3 ph.etc., complete. (1 working and 1 standby).
129	Membrane Dosing Pumps: Electronic dosing pump to be mounted both on its base as well as hung on the wall. Pumps following CE regulations, IP- 65 protection. Power connections : 220/240V, 50/60 Hz. The materials in contact with liquid are : Ploypropylene,Viton, Teflon and PVC. Includes anti-acid plastic case. Operating panel protection provided by a transparent polycarbonate cover. Lubrication not required. Flow 20L/hr @ 5 bar
130	Chemical Storage Tanks: Supply, Installation, Testing & Commissioning of Semi transparent polyethelene tank with external scale so that levels can be checked easily, capacity of tank 500lts .etc., complete
131	Supply, Installation, Testing & Commissioning of Agitators for easy installation in the tanks, provided with steering grip in bakelite, rod and propellor arms in PVC .. length of stirring rod 900mm. etc., complete
132	Agitators: Supply, Installation, Testing & Commissioning of Agitators for easy installation in the tanks, provided with steering grip in bakelite, rod and propellor arms in PVC .. length of stirring rod 900mm. etc., complete
133	UV system with minimum 60 m3/h with onfiguration, low pressure UV lamps powered by magnestic ballast housed within a separate wall mounted panel. The lamp power shall be adjusted from the control panel and when the pool is not in use the lamp output shall be set to low. The UV reactor incorporates a automatic wiper system which shall allow cleaning of the internal thimble housing the UV lamp. The reactor vessel shall be in SS 316 L and flanges shall conform to BS 4504, lamp shall be made of high purity quartz. The wiper ring shall be spring loaded PTFE. The system shall also incorporate lamp replacement indicator and lamp failure alarm. As an option the system shall also incorporate UV intensity meter.
134	Pool Drains : Supply, Installation, Testing & Commissioning of Drain grille. Stainless steels grille with screws, 500 mm x 500 mm in AISI 304.EN 13451 Standard Max. recommended flow 43 m3/h (0,5 m/s).etc., complete.
135	Suction Inlet : Supply, Installation, Testing & Commissioning of Suction inlet in ABS with cap internal thread of 1 1/2\\" dia and external thread 2\\" .etc., complete
136	PVC wall conduits: Supply, Installation, Testing & Commissioning of PVC wall conduits 300mm long. Rear connection to pipe by 2\\" .etc., complete
137	Inlets: Supply, Installation, Testing & Commissioning of White ABS plastic bottom inlet for concrete with S.S. screws and regulable .Flow/ inlet = 9,000 l/hr. EN-13451-1 Standard.etc., complete
138	Overflow Gutter Drains: Supply, Installation, Testing & Commissioning of drain fitting with body grille in ABS
139	Ladders: Supply, Installation, Testing & Commissioning of Ladder of width 500 mm with Ø 43 handrails in hand polished AISI-316 stainless steel. Complete with fixing anchors and earth connection. With added top double safety step and increased overall height in accordance with EN 13451-2Standard. Includes non-slip LUXE steps in AISI-316 stainless steel. 3 Steps. etc., Complete.
140	Underwater Lights: Supply, Installation, Testing & Commissioning of Led 36W light with Niche and ABS/SS 316 Faceplate
141	Underwater Lights: Supply, Installation, Testing & Commissioning of Led 18W light with Niche and ABS/SS 316 Faceplate
142	Junction Boxes: Supply, Installation, Testing & Commissioning of Junction Boxes, made in ABS, composed of 3 entries 3/4\\" .UNE 20324 : 1993 +1a MOD:2000(EQV a EN 60529:1991 + ERRATUM + A1:2000)+ERRATUM:2004.etc., complete
143	Flexible Cable Conduits: Supply, Installation, Testing & Commissioning of Cable Conduit Hose, Flexible 1 mt. long conduit for connecting light to junction box. 3/4\\" .etc., complete.
144	Transformers/power supply for light: Transformers with IP 64 protection, 300VA from 220V to 12V
145	Supply, Installation, Testing and Commissioning of Ball Valve of dia 63 mm
146	Supply, Installation, Testing and Commissioning of Butterfly Valve Dia of 90 mm
147	Supply, Installation, Testing and Commissioning of Flange and Adaptor for 90 mm dia Butterfly Valve.
148	Supply, Installation, Testing and Commissioning of Butterfly Valve of Dia 110 mm
149	Supply, Installation, Testing and Commissioning of Flange and Adaptor for 110 mm dia Butterfly Valve. .
150	Supply, Installation, Testing and Commissioning of Butterfly Valve Dia 160 mm
151	Supply, Installation, Testing and Commissioning of Flange and Adaptor for 160 mm dia Butterfly Valve.
152	Supply, Installation, Testing and Commissioning of Wafer Check Valve of Dia 90 mm
153	Supply, Installation, Testing and Commissioning of Wafer Check Valve of Dia 160 mm
154	Supply, Installation, Testing & Commissioning of Metallic vaccum head in polished Al and chrome bronze - 1.5\\" length 442mm.
155	Supply, Installation, Testing & Commissioning of Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf, skimmers and scoops.10.0mts. Long with Handle adaptor .
156	Supply, Installation, Testing & Commissioning of Transparent blue plastic vacuum hose 11/2\\" dia 30mtrs long including hose cuffs for connection to suction inlets .etc., complete.
157	Supply, Installation, Testing & Commissioning of Deep bag net made in polypropelene and white polyester netting, Shark Series.etc., complete
158	Supply, Installation, Testing & Commissioning of Surface net made in polypropelene and white
159	Supply, Installation, Testing & Commissioning of Curved brushes made in polypropelene for pool
160	Supply, Installation, Testing & Commissioning of Straight brushes made in polypropelene for pool .
161	Supply, Installation, Testing & Commissioning of Algae brushes with stainless steel bristles .etc., complete
162	Supply of Test kit for free chlorine & pH
163	Supply of Chlorine Testing Tablets - 250 nos. in a pack
164	Supply of Phenol (pH) reagent-250 Tablets
165	Supply of pH increasing chemical compound for swimming pool
166	Supply of pH decreasing chemical compound for swimming pool
167	Supply of Algaecide
168	Supply of TCCA Granules
169	Supply, Installation, Testing & Commissioning of 63 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard
170	Supply, Installation, Testing & Commissioning of 90 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard
171	Supply, Installation, Testing & Commissioning of 110 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard
172	Supply, Installation, Testing & Commissioning of 140 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard
173	Supply, Installation, Testing & Commissioning of 160 mm dia UPVC pipe 10 kg/sqcm including fittings where required e.g. tees, bends. etc., complete. EN 1452 Standard
174	Supply, Installation, Testing & Commissioning of 4x2.5 mm2 Copper cable for under water light from Junction box to Electrical panel of U/W Light, complete with Conduit.
175	Supply, Installation, Testing & Commissioning of 3x4 mm2 Copper cable for under water light from Junction box to Electrical panel of U/W Light, complete with Conduit.
176	Supply,Installation, Testing & Commisioning of control panel for Centrifugal Pump 5.5HP (Filtration-1W+1S) -2 No's, 2. Dosing Pump-2. 300W Transfomer-4No's,. complete as required, MCC panel as described, complete: Contactors,Push Button & Indicators,Selector Switch, Ammeter,Volt Meter, Lugs, Wires, Enclosure.
177	Bill No. XIII: Landscape
178	Dismantling of Brick/Tile Work as per MoRD Technical Specification No. 202 Dismantling of existing structures like culverts, bridges, retaining walls and other structures comprising of brick masonry icluding disposal of unserviceable material and stacking the serviceable material with all lift upto a lead of 1000 m as per MoRD Technical Specification clause 202.D) Dry Brick Pitching or Brick Soling
179	Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed: -All kinds of soil
180	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
181	Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8.
182	Granular sub-base with Well Graded Material (Table 400.1) using Jhama Brick Aggregate(A) By Mix in Place MethodConstruction of granular Sub-base by providing well graded material (Jhama Brick aggregates) spreading in uniform layers with motor grader on prepared surface, mixing by mix in place metjod with rotovator at OMC, and compacting with smooth wheel rollr to achieve the desired densitty, complete as per MoRD Technical Specification Clause 401.(i) For Grading-I Material
183	18 mm thick Polished Jhansi Red Granite flooring iin pathways and foothpaths
184	Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All Work upto Plinth Level1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size)
185	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All Work upto Plinth Level1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size)
186	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size)
187	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size)
188	Gravel / Soil - Aggregate Surface Course ( Table 400.3 )Construction of gravel / soil - aggregate surface course by providing well graded material, spreading in uniform layers with Tractor mount grader on prepared surface, mixing by mix in place method with Tractor mount rotavator at OMC, and compacting with three wheel 80 - 100 kN static roller to achieve the desired density, complete as per Technical Specification Clause 402.
189	Providing and laying at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1 : 3 ( 1 cement : 3 fine sand) including the cost of required centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 ( 1 cement : 3 fine sand) on exposed surface complete.1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
190	80 mm thick factory made c.c interlocking paver block of M-35 GradeProviding and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge:(a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. Cement concrete 1:2:4 in pavements, laid to required slope and camber in panels
191	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
192	Providing weep holes on brick masonry/ plain/ reinforced concrete wall with 90 mm dia uPVC pipe with ISI mark of approved/ reputed make extending through the full width of the structures with slope of 1(V):20(H) towards drawing face including cutting, fixing etc. complete as per drawing and direction of the Engineer-in-Charge and technical specification.
193	Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge.
194	Centering, Shuttering including struttings, propping etc and removal of form work for:Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply
195	Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.
196	Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 3.84 kg/10 sqm)
197	Providing and fixing as per drawing /image STAINLESS STEEL DUSTBIN SERIES : Wheel dustbin capacity 1100 ltr 4 wheels with lid 1360x1060x1370 HDPE
198	Providing and fixing stainless steel ( Grade 304) Sign board / Benches, chair, Scultures, canoppy made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing tubes, channels, plates etc., including welding, grinding, and making curvature (wherever required) and fitting the same withbuffing, polishing necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.-Making the Sign board on S steel sheet
199	Supply and Installation of HDPE Docks/Folating jeety size 666mmx666mmx400mm with hand rails
200	Bill No. XIV: Horticulture
201	Fine dressing the ground
202	Mixing earth and sludge or farm. yard manure in proportion specified or as directed.
203	Spreading of Sludge / Farm Yard Manure / good EarthSpreading of sludge/ farm yard manure/ good earth in required thickness (cost of sludge, farm yard manure or/and good earth to be paid for separately) MoRT&H technical specifications Clauses 307.
204	Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm Thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and then rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of Officer-in-charge
205	Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of Officer-in-charge.
206	Mixing earth and sludge or faRmt. yard manure in proportion specified or as directed.
207	Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farm-yard manure (cost of well decayed farm yard manure to be paid separately) in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and liftsHoles 1.2 m dia and 1.2 m deep.
208	Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farm-yard manure (cost of well decayed farm yard manure to be paid separately) in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and liftsHoles 60 cm dia, and 60 cm deep.
209	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Syzygium cumini (Jambhun),Minimum 3.0/3.5m overall height,Minimum 50mm caliper,Multibranching at 2.0m from collar
210	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Butea monosperma (palash),Minimum 3.0/3.5m overall height,Minimum 60mm caliper, Multibranching at 2.0m from collar
211	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Ficus infectoria (Payari) ,Minimum 3.0/3.5m overall height,Minimum 60mm caliper, Multibranching at 2.0m from collar
212	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Aegle marmelos (Beal),Minimum 3.0/3.5m overall height,Minimum 40mm caliper,Multibranching at 2.5m from collar
213	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Terminalia arjuna (Arjun),Minimum 3.5m overall height,Minimum 60mm caliper, Multibranding at 2.00m
214	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Mimusops elengi (Bakul)Champa,Minimum 3.0/3.5m overall height,Minimum 75mm caliper,Multibranching at 1.5m from collar
215	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Shorea robusta (Sal),Minimum 3.0/3.5m overall height,Minimum 60mm caliper,Multibranching at 2.0m from collar
216	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Anthocephalus cadamba (kadamba),Minimum 3.0/3.5m overall height,Minimum 75mm caliper,Multibranching at 1.5m from collar
217	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Mangifera indica(Mango),Minimum 3.0/3.5m overall height,Minimum 60mm caliper,Multibranching at 2.0m from collar.
218	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Azardita indica (Neem),Minimum 3.0/3.5m overall height,Minimum 60mm caliper,Multibranching at 2.0m from collar
219	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ERYTHRINA INDICA,Minimum 3.0/3.5m overall height,Multibranching at 2.5m from collar, min. 60m Caliper.
220	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-GARDENIA LATIFOLIA,CAPE JASMINE,,Multibranching at 2.0m from collarMinimum 2.0/2.5m overall height,
221	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JACARANDA MIMOSIFOLIA,NEELA GULMOHAR,Minimum 3.0/3.5m overall height,Minimum 60mm caliper,Multibranching at 2.0m from collar.
222	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-LAGERSTOEMIA THORELLII,Minimum 3.0/3.5m overall height,Minimum 60mm caliper,Multibranching at 2.0m from collar.
223	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-MALALEUCA LEUCADENDRON,GOLDEN BOTTLE BRUSH,Minimum 2.0/2.5m overall height,Minimum 40mm caliper,Multibranching at 2.0m from collar.
224	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-PLUMERIA ALBA,FRANGIPANI,Minimum 3.0/3.5m overall height,Minimum 75mm caliper,Multibranching (4-5) branches at 1.5m from collar.
225	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-PLUMERIA RUBRA,RED Champa,Minimum 3.0/3.5m overall height,Minimum 75mm caliper,Multibranching (4-5) branches at 1.5m from collar.
226	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingALSTONIA SCHOLARIS Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
227	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingBAUHINIA BLACKEANA (KACHNAR), Minimum 3.5/4.0m overall height, Minimum 55-60mm caliper, Multibranching at 2.0m from collar
228	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingBAUHINIA PURPUREA (KACHNAR PURPLE) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
229	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingBAUHINIA VAREGATA (KACHNAR WHITE) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
230	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingBOMBAX MALABARICUM (SAVAR) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
231	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingCALISTEMON LANCEOLATUS (BOTTLE BRUSH) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
232	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingCASSIA FISTULA (AMALTAS) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
233	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingCASSIA JAVANICA (PINK CASSIA) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
234	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingCORDIA SEBESTINA (SCARLET CORDIA) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
235	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingDELONIX REGIA (GULMOHAR ) Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
236	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingLAGERSTROEMIA FLOS REGINAEMinimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
237	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingMELIA AZEDARACH Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
238	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingNYCANTHES ARBORTRISTIS Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
239	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingPELTOFORUM FERRUGILUM Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
240	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingSCHLEICHERA OLEOSA Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
241	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingTABEBUIA ARGENTEA Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
242	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingANOGEISSUS PENDULA Minimum 3.5/4.0m overall height,Minimum 60mm caliper, Multibranching at 2.5m from collar
243	PALMSSupply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingARECA PALM-SUPARI,Minimum 5 canes per palm
244	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingROYESTINIA REGIA,Minimum 3.5m overall height,Minimum 100mm caliper,5 fronds.
245	Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingFOX TAIL PALM,Minimum 3.5m overall height,Minimum 100mm caliper,5 fronds.
246	SHRUBSSupply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ACALYPHA HISIPIDA CAT TAIL,Minimum 600mm height@900mmc/c,Bushy, Multibranching, Flowering.
247	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ACALYPHA W GREEN,Minimum 600mm height@750mmc/c,Bushy, Multibranching.
248	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ACALYPHA W RED,Minimum 600mm height@750mmc/c,Bushy, Multibranching
249	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ACALYPHA TRICOLUR,Minimum 600mm height@750mmc/c,Bushy, Multibranching
250	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ALLAMANDA NERIFOLIA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering
251	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CAESALPINIA PULCHERRIMA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering
252	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA EMARGINATA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering
253	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA HAEMATOCEPHALLA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering.
254	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CASSIA BIFLORA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering
255	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA BREVIPES, Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering.
256	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-LAGERSTROEMEA INDICA (Species Muve, white, Pink Red) CANDIDA ,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering
257	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Nerium oleander 'Petite Pink' Dwarf Pink , Minimum 900mm height@750mmc/c,Bushy, Multibranching, Flowering
258	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CESTRUM ELEGANS,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering
259	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HAMELIA PATTENS,Minimum 1500mm height@900mmc/c,Bushy, Multibranching
260	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS ROSA PROLIFIC,Minimum 600mm height@600mmc/c, Bushy, Multibranching
261	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS DAFFODIL YELLOW,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering
262	Supply & Install Shrubs inclusive of:i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift.ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration (5 ml/liter water) as required.iii). Flooding the pit with water after making kiaries where required.vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of plantingHIBISCUS ROSA SINENSIS ( RED SATIN),Minimum 600mm height @600mmc/c, Bushy, Multibranching, Flowering
263	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IXORA CHENENSIS,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering
264	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JASMINUM HUMILE,Minimum 900mm height@600mmc/c,Bushy, Multibranching, Flowering
265	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-NERIUM OLEANDER Variegatum Plenum,Minimum 900mm height@900mmc/c, Bushy, Multibranching, Flowering
266	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-TABERNAEMONTANA CORONERIA,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering
267	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-TABERNAEMONTANA CORONERIA VARIEGATED,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering
268	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-GARDENIA JASMINOIDES,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering
269	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-HIBISCUS COOPERII,Minimum 600mm height@750mmc/c,Bushy, Multibranching, Flowering
270	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IXORA CHENENSIS,Minimum 600mm height@900mmc/c,Bushy, Multibranching, Flowering
271	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JATROPHA PAUNDARAEFOLIA,Minimum 600mm height@900mmc/c,Bushy, Multibranching, Flowering
272	Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-TECOMARIA CAPENSIS,Minimum 600mm height@900mmc/c,Bushy, Multibranching, Flowering
273	COURTYARD PLANTSSupply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-RAPHIS PALM,Minimum 600mm height @300mmc/c,3 /4fronds
274	CLIMBERSSupply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ANTIGNON LEPTOPUS,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
275	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-BEAUMONTIA GRANDIFLORA,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
276	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-BOUGAINVELLEA spp. Mix,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
277	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CLERODENDRON SPLENDENS ,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
278	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IPOMEA CURELEA,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
279	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-IPOMEA PURPUREA,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
280	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-JASMINUM NITIDUM,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant
281	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-QUISQUALIS INDICA,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant.
282	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-THUNBERGIA ALATAMinimum 600mm height @2000mmc/c,Minimum 3 runners per plant.
283	Supply & Install Climbers inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-VERNONIA ELAEAGNIFOLIA ,Minimum 600mm height @2000mmc/c,Minimum 3 runners per plant.
284	GROUND COVERSMixing earth and sludge or faRmt. yard manure in proportion specified or as directed.
285	Supply & Install gound covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ALTERNENTHERA RED,Minimum 150mm height @200mmc/c,Bushy.
286	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CHLOROPHYTUM COSMOSUM,Minimum 150mm height @200mmc/c,Minimum 3 runners per plant.
287	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-IRESINE,Minimum 150mm height @200mmc/c, Minimum 3 runners per plant.
288	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-IPOMEA GOLDEANA, Minimum 300mm height @200mmc/c, Minimum 3 runners per plant.
289	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-OPHIOPOGON BLACK GRASS.
290	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-SYNGONIUM MACROPHYLLUM,Minimum 150mm height @200mmc/cMinimum 3 runners per plant.
291	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-WEDELIA TRILOBATA,Minimum 3 runners per plant,Minimum 150mm height @200mmc/c.
292	Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ZEBRINA PENDULA,Minimum 300mm height @250mmc/c,Minimum 3 runners per plant.
293	HEDGESSupply & Install plants to form hedge , inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MURRAYA EXOTICA,Minimum 300mm height @300mmc/c,Bushy
294	Supply & Install plants to form hedge inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CLERODENRON MACROSIPHON,Minimum 350mm height @200mmc/c,Bushy
295	Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-DURANTA GOLDEN PLUMERI Minimum 300mm height @200mmc/c,Bushy
296	Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CLERODENDRON INERME,Minimum 300 mm height @200mmc/c,Bushy
297	Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.LOROPETALUM CHINENSIS Minimum 450mm height @450mmc/c,Bushy
298	Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MURRAYA PANICULATA Minimum 300 mm height @300mmc/c,Bushy
299	Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-FICUS LONGISLAND Minimum 150mm height @200mmc/c,Bushy
300	Supplying at site of work well-decayed farm.-yard manure, from any available source, approved by the Engineer-in-charge including screening and stacking.
301	Supplying site of work-Deoiled Neem-Cake duly packed in used bags
302	Supplying at site of work sludge duly stacked at site.
303	BAMBOOSupply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Dendrocalamus Strictus(Velu),Minimum 3.0/3.5m overall height, 60MM CALIPER, Multibranching at 2.5m from collar
304	Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.Bambusa Vulgaris (GOLDEN BAMBOO), Minimum 2400mm height, (4-5) Stems in one clump
305	Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.Dendrocalamus Asper (ROUGH GIANT BAMBOO), Minimum 2.5m height, 150 Dia
306	Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting. ,Bambusa Wamin (Buddha Belly Bamboo), Minimum 1.8 m height, Clumps of 2/3 Stems.
307	Supply & Install Grasses inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting. ,Cymbopogon Citratus (Lemon Grass), Minimum 600mm height, Clumps of 20/25 Grass Shoots.
308	Bill No. XV: Sanitation & Plumbing
309	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15 mm nominal outer dia .Pipes.
310	20 mm nominal outer dia .Pipes.
311	32 mm nominal outer dia .Pipes.
312	Providing and fixing Chlorinated PolyvinylChloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain &brass threaded fittings This includes jointing of pipes& fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete asper direction of Engineer in Charge. - External work32 mm nominal outer dia .Pipes.
313	50 mm nominal outer dia .Pipes.
314	Providing and fixing on wall face unplasticised RigidPVC rain water, soil, waste & vent pipes (workingpressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:Single socketed pipe - 75 mm OD
315	Single socketed pipe - 110 mm OD
316	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: - Coupler75 mm
317	110 mm
318	Single equal tee with door - 75x75x75 mm
319	110x110x110mm
320	Bend 87.5° - 75 mm
321	110mm
322	Single unequal junction of required degree with door - 110x110x75 mm
323	Providing and fixing unplasticised -PVC pipe clips ofapproved design to unplasticised - PVC rain water,soil, waste & vent pipes by means of 50x50x50mmhard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. - 75 mm
324	110mm
325	Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests.
326	Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid.
327	Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required : Single squatting plate with 5 litre P.V.C. automatic flushing cistern.
328	Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern.
329	Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineerin- Charge.
330	Providing and Fixing white vitreous china flat backhalf stall urinal of size 580x380x350mm with whitePVC automatic flushing cistern, with fittings,standard size C.P. brass flush pipe, spreaders withunions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern.
331	Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern.
332	Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps,32 mm C.P. brass waste ofstandard pattern, including painting of fittings andbrackets, cutting and making good the wallswherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
333	White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps.
334	Providing and fixing white vitreous china pedestal forwash basin completely recessed at the back for thereception of pipes and fittings.
335	Providing and fixing Stainless Steel AISI 304 (18/8)kitchen sink as per IS 13983 with C.I. brackets andstainless steel plug 40 mm including painting of fittingsand brackets, cutting and making good the walls wherever required: - Kitchen sink with drain board510x1040 mm bowl depth 250mm.
336	Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white
337	Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.
338	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe - 32 mm dia
339	40 mm dia
340	Providing and fixing 100 mm sand cast Iron grating for gully trap.
341	Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia
342	Rectangular shape 453x357mm
343	Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
344	Providing and fixing toilet paper holder : C.P Brass
345	Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38mm single piece moulded with height of270mm, effective length of tail pipe 260mm from thecentre of the waste coupling 77mm breadth with 25mmminimum water seal, weighing not less than 263gms.
346	Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms.
347	Providing and fixing PTMT towel rail complete withbrackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved qualityand colour- 600mm long towel rail with total length of 645mm, width78mm and effective height of 88mm, weighing not lessthan 190gms.
348	Providing and fixing brass bib cock of approved quality : 15 mm nominal bore
349	20 mm nominal bore
350	Providing and fixing brass stop cock of approved quality : 15 mm nominal bore
351	20 mm nominal bore
352	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore
353	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore
354	32 mm nominal bore
355	Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : 20 mm nominal bore
356	25 mm nominal bore
357	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever equired) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
358	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter
359	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 - 15 mm nominal bore
360	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
361	EXTERNAL PLUMBINGEarth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
362	REINFORCED CEMENT CONCRETE WORKReinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Mild steel and Medium Tensile steel bars.
363	WATER SUPPLYProviding and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329150 mm dia Ductile Iron Class K-7 pipes
364	Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K 9 conforming to IS : 8329 :100 mm dia Ductile Iron Double Flanged
365	150 mm dia Ductile Iron Double Flanged
366	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) - 100 mm diameter Class II
367	Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately): 100 mm dia
368	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.75 mm nominal inner dia .Pipes.
369	Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 finesand) for sluice valve, with C.I. surface box 100mm.top diameter, 160 mm bottom diameter and 190mm deep ( inside) with chained lid and RCC topslab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) necessary excavation foundation concrete 1:5:10 (1 cement : 5fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1cement : 3 coarse sand) 12 mm thick finished with afloating coat of neat cement complete as perstandard design : With Second Class bricks
370	Providing, installation and commissioning of package type Iron Removal Plant comprising of Iron Removal Filter of dual media filter with anthracite coal, filter gravel, polypropelene double hexagonal nut strainer etc., mixing chamber for coagulants like sodium alluminates etc., oxidation chamber with manganese dioxide , metering pump for coagulant dosing, air compressor of suitable capacity with motor, back washing arrangements, disinfection with sodium hypochlorite solution through metering pump, all necessary pipes for raw water collection, inter connecting all the chambers, delivery outlet of 150 mm dia alongwith all related civil, mechanical and Electrical works etc. complete as per approved drawing, process flow, technical specification and direction of the Engineer - in - charge.2500 G.P.H CAPACITY
371	Charges for drilling and boring of pilot hole in any soil strata bywater jet or any suitable method including collection ofsamples at various suitable levels and preservation ofsamples in polythene bags / sample boxes and disposal ofexcess soil or mud and maintain the pilot hole properly andrequired staging as per specification ( IS : 2800 ) and directionof the Engineer-in-charge.100 mm dia
372	Reaming of pilot hole to an enlarged bore hole in any soilstrata by manual means, disposal of excess soil or mud,including the cost for water etc. as required to maintain thebore hole properly as per specification and direction of theEngineer - in - charge.from 100 mm dia pilot hole to 250 mm bore hole
373	Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer - in - charge. 'CM' Casing pipe - 150 mm dia
374	125 mm dia
375	RS Pipe - 100 mm dia
376	Washing & development of Tube Well by using hand pump or by any suitable method & testing of the well as per specification & direction of the Engineer in charge
377	Providing and fixing of UPVC end cap suitable for UPVC ‘CM’ casing or ‘CS’ casing or ‘RS’ pipes as per specification and direction of the Engineer-in-charge.100mm dia.
378	Providing and fixing of UPVC reducer suitable for UPVC ‘CM’ casing or ‘CS’ casing or ‘RS’ pipes as per specification and direction of the Engineer-in-charge.150 x 100 mm dia
379	Providing and fixing of housing clamp ( made with 12 mm thick MS sheet ) along with well cap (made with 10 mm thick MS sheet ) with necessary arrangements for SBDTW as per specification and direction of the Engineer - in - charge.150 mm dia
380	Providing and shrouding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer - in - charge.with contractor's rigwith pea gravels obtained from Durgapur, West Bengal.
381	Providing and Installation of 3 HP (single/three phase) submerssible Pump (Electrical) as per relevent IS code with LT control panels connected with 100 mtr insulated cables from the distribution lines, 2 nos. electric pole of 8.5 mtr long 7/16 cable, well cap, housing clamp, column pipes, single/three phase earthing, motor starter, control panel box with locking arrangement with all accessories complete as per the direction fo the Engineer-in-charge.For Borewell
382	Providing and Installation of 1 HP Domestic mono block pump
383	SEWAGE AND DRAINAGEProviding, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete.150 mm diameter
384	Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :
385	Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.
386	Supplying and fixing C.I. cover without frame for manholes500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg.
387	Supply,Installation, Testing and Commissioning of Underground Fully Advanced Automatic Sewage Treatment Plant of Capacity of 20 KLD including solar packeg to run the plant on solar energy.
388	SOLID WASTE COMPOSTING PLANTSupply, Installation and Commissioning of Fully Automatic Electro-mechanically operated Organic Waste Composting machine handeling Maximum intake capacity 50kg/day.with Shredder 3HP (Dual Shaft).12-month warranty from the date of supply for parts against manufacturing defect.
389	Bill No. XVI: Goods
390	Supply and installation of Play EquipmentsSupply and Fixing of Swing
391	Supply and Fixing of Spring Rider Type-I
392	Supply and Fixing of Spring Rider Type-II
393	Supply and Fixing of Pyramid Net Climber
394	Supply and Providing Race Treadmill -
395	Supply and Providing Multi Gym Equipment
396	Supply and Providing Transformer+
397	Supply and Providing Dumbells -
398	Supply and Providing Spin Bike
399	Supply and Providing Multi- Functional Trainer with smith Machine
400	Supply and Providing Leg press
401	Supply and Providing Pec deck fly
402	Supply and Providing Leg Pull down and Row
403	Supply and Providing Leg Ext and curl
404	Supply and Providing Flat simple bench
405	Supply and Providing 32mm/25mm thick GYM floor mat
406	Supply and Providing Yoga Mat
407	Supply and Providing Mirror
408	Supply and Providing Elite-Adjustable Bench
409	Supply and Providing 3 Burner Cooking Stove -
410	Supply and Providing SS Working Table Type 1
411	Supply and Providing 3 Bowl Kitchen Sink -
412	Supply and Providing GI Hood Kitchen Exhaust with Filter -
413	Supply and Providing Gi hood Duct Line
414	Supply and Providing SS Working Table Type 2
415	Supply and Providing 5 HP Exhaust Fan
416	Supply and Providing SS Kitchen Rack
417	Supply and Providing Double Door Cooler of 850 Litre Capacity
418	Supply and Providing Double Door Deep Freezer of 320 Litre Capacity
419	Supply and Providing Single Door 45L Mini Fridge
420	Providing and fixing in play equipment , including excavation of 0.45 x 0.45 x 0.45 m size pit and fixing the each supporting leg / anchoring arm. of playing instrument in grade concrete block of 0.45 x 0.45 x 0.45 m size including curing etc. complete including providing for epdm flooring at all fall areas (min 1.50x 1.50 m ).A-Multi activity play equipment with straight tube slide of 3' ht, small wave slide 3' ht with slide entry, an railing with abacus play system, an FRP steps to climb to a metal sq deck with canopy.-Play zone 35' x 25'-Max platform. ht 3'-Age group 3-6 yrs
421	Multi activity play equipment with 1. double wave slide of 5' ht, 2. spiral slide 5' ht with slide entry, bridge 2nos, 3. metal plain bridge 8' length with cross checked railing assembly and 4. swinging bridge with railing assembly, 5. railing with cross and zero play system, 6. an metal ladder 5' height, and 7. 3 nos metal sq deck with canopy ( 2nos) and without canopy( 1 nos) .8. crawl tube below 8' length below deck.9. metal rock climber 5' height. with hand rails at suitable positionsand a clinging bar.-Play zone 40' x 36' approx-Max platform. ht 5'-Age group 5-12 yrs
422	Providing and fixing Tri basket, Area :2.0m Dia Safe Play Area : 3.5m Dia (11.5ft Dia) Ideal For 5-14Years,Friends at a time :4-6 on suitable location at smart park
423	Providing and fixing see - saw Product Area :0.4m X 0.75m,Safe Play area:1.4m X2m,Ideal For : 3-8 YearsFriends at a time :2, on suitable location at smart park
424	Providing and fixing Standard See-saw, Product Area : 2.5m X 0.3m, Safe Play Area :3.5m X1.3m, Ideal For :4-10 Years, Friends at a time : 2 no.on suitable location at smart park
425	Providing and fixing Double Post Swing,Area : 3.5m x 1.0m,• Safe Play Area : 4.5m X 2.0m • Ideal For : 4-14 Years, Friends at a time : 2 on suitable location at smart park,
426	Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. complete. of FRP Wave Slide 1.5 Mtr having Dimension: • Product Area : 5m x 0.6m (18ft x 8.2ft) • Safe Play Area : 6.5m x 3.5m (21.3ft x 11.5ft) • Age Group : 4-12 yrs.Product details as per attached Specification.
427	Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. complete. of Delux slide 1.5 mtr having Dimension: • Product Area : 4.5m x 0.7m (14.8ft x 2.3ft) • Safe Play Area : 5.5m x 1.7m (18ft x 5.6ft)-Age Group : 4-12 yrs. Product details as per attached Specification.
428	Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. of FRP Double Roller Slide 1.5 Mtr having Dimension: • Product Area : 6.5m x 2.5m (21.3ft x 8.2ft) • Safe Play Area : 7.5m x 3.5m (24.6ft x 11.5ft) • Age Group : 4-12 yrs.- Product details as per attached Specification.
429	Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. of Multi seater see-saw having Dimension: • Product Area : 0.5m X 3m (1.6ft X 9.8ft) • Safe Play Area : 1.5m X4m (4.9ft X 13.1ft) • Ideal For : 3-10 Years • Friends at a time : 4 - Product details as per attached Specification.
430	Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc. of Simply Go Round having Dimension• Product Area : 1.5m Dia ( 5 ft Dia.)• Safe Play Area : 2.5m Dia ( 8.2ft Dia.)• Ideal For : 5-12Years• Friends at a time : 5-7 . Product details as per attached Specification.
431	Providing & Fixing of play equipment , including excavation,making concrete foundation for play equipment,anchoring with fastner,epdm flooring etc.of PYRAMID SCRAMBLER having Dimension: • Age Group :- 6 - 12 yrs. Product Area :- 5 m x 5 m Safe Play Area :- 6 m x 6 m. Product details as per attached Specification.
432	Bharat AC001 10 KW Charger(3 Socket)Installation and Commissioning of Bharat AC001 10 KW Charger(3 Socket)One time on-boarding setup charges of Bharat AC001 10 KW Charger(3 Socket)
433	AC Level -2 Charger 7.4 KWInstallation and Commissioning of AC Level -2 Charger 7.4 KWInstallation and Commissioning of AC Level -2 Charger 7.4 KW
434	DC Fast Charger CCS-2 30 KW Single GunInstallation and Commissioning of DC Fast Charger CCS-2 30 KW Single GunOne time on-boarding setup charges of DC Fast Charger CCS-2 30 KW Single Gun
435	DC Fast Charger CCS-2 40 KW Double GunInstallation and Commissioning of DC Fast Charger CCS-2 40 KW Double GunOne time on-boarding setup charges of DC Fast Charger CCS-2 40 KW Double G
436	Bill No. XVII: Furniture
437	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Sal Wood
438	Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete.Kiln seasoned and chemically treated hollock wood
439	French spirit polishing [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new works including a coat of wood filler
440	Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked to frame, backing or studding with screws etc. complete. (Frames, backing or studding to be paid separately): - 12 mm thick
441	18 mm thick
442	Providing and fixing aluminium tee channels (heavy duty) with rollers, stop end in pelmets as curtain rod.
443	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality.1.5 mm thick
444	Providing and fixing Pre-laminated medium density fibre board conforming to IS: 14587:1998 marked, with one side decorative lamination and other side balancing lamination Grade-I(exterior grade), in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately) 25 mm thick
445	Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete.
446	Providing and fixing powder coated telescopic drawer channels 300mm long with necessary screws etc. complete as per directions of Engineer-in-charge.
447	Providing and fixing in position wall panelling at all heights with 6 mm thick BWP ply board lapping with 4 mm thick Teak Veneer of approved quality in outer face, decorative teak wood bead (50 x 40 ) at top and skirting (150 x 25), comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally ply board are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm all complete as per manufacturer's specification as per direction of Engineer-in-Charge all complete.
448	Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.200 mm
449	Providing and supplying Unbranded Wooden Chair of approved quality, design, and make, made from seasoned hardwood (such as teak / rubberwood / beech wood or equivalent), suitable for office, visitor, or general seating use, conforming to the following specifications and requirements, complete as directed by the Engineer-in-Charge.
450	Providing and supplying Star Homz Cotton Mattress, factory-made, of approved make and quality, weighing not less than 12 kilograms, conforming to the following technical specifications, complete as directed by the Engineer-in-Charge.
451	Providing and supplying STAR HOMZ Cotton Mattress weighing 12 kilograms (±5%), manufactured from high-quality long-staple cotton properly carded and layered, enclosed in a cotton / woven fabric cover of approved shade and pattern.The mattress shall be uniformly filled, well-quilted, and neatly stitched on all sides to retain shape and firmness during use.All materials used shall be clean, hygienic, and free from synthetic fibre or impurities.The mattress shall be comfortable, durable, and suitable for regular institutional / domestic use.Type: Cotton Mattress – 12 KgComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
452	Providing and supplying Star Homz Pillow Cover, made from Khadi fabric conforming to IS:13717/1993, of approved shade and quality, size 59 cm (±0.5 cm) × 33 cm (±0.5 cm), neatly stitched and finished, complete as directed by the Engineer-in-Charge.
453	Providing and supplying unbranded dining table of approved design and size, made from seasoned hardwood / MDF / engineered wood, with golden finish or coating, complete as directed by the Engineer-in-Charge.
454	Providing and supplying L-shaped Reception Table, make Keshav’s (Keshav Enterprises) or equivalent approved, of modern modular design, ergonomically constructed from high-quality materials, with durable finish, cable management provisions, and smooth edges, complete in all respects as directed by the Engineer-in-Charge.
455	Providing and supplying Computer Table with Additional Unit, make AARIHANT CRAFT – GLOBAL MARKETING or approved equivalent, made from high-quality pre-laminated boards with modern design, durable hardware, and fine finish, suitable for office, computer lab, or home workstation use, complete as directed by the Engineer-in-Charge.
456	Providing and supplying SAGAR SHREE FURNITURE Aluminium Powder-Coated Wicker Furniture, made of high-grade Aluminium frame (min. 1.2 mm thick) with polyester powder coating (min. 60 microns), woven with 100% virgin HDPE synthetic wicker (UV stabilized, all-weather resistant).Cushions made of high-density polyurethane foam (min. 32D) covered with 180 GSM polyester acrylic outdoor fabric, UV- and water-resistant.All fasteners of Stainless Steel (Grade 304).Furniture shall be weather-proof, corrosion-resistant, and suitable for outdoor use.Finish: Smooth, uniform, and scratch-resistant.Color and design as approved by Engineer-in-Charge.The item shall conform to relevant IS standards (IS:13871, IS:12775, ASTM G154).Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
457	Providing and supplying DTS Sofa / Couch – 1 Seater, constructed with a hardwood internal frame (seasoned and chemically treated), high-density foam cushioning (min. 32D for seat, 28D for back), upholstered with premium fabric / leatherette of approved shade and texture.Armrests and seat edges to be smoothly contoured; bottom supported on sturdy wooden or metal legs with anti-skid buffers.All materials to be of IS-approved quality, joints glued and screwed for rigidity.Finish to be smooth, durable, and free from wrinkles or loose threads.Overall dimensions: approx. 900 mm (W) × 850 mm (D) × 850 mm (H) (±5%).Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
458	Providing and supplying High-Back Revolving Chair, ergonomically designed with adjustable seat height and 360° revolving mechanism, mounted on a five-star nylon / metal base with twin-wheel castors for smooth mobility.Chair fitted with gas lift for height adjustment, tilt tension mechanism with locking system, and PU-moulded seat and back cushions upholstered with breathable fabric or mesh of approved shade.Backrest to be high-back type with lumbar support; armrests made of durable polypropylene / PU-padded material.All components shall be rust-free, sturdy, and smoothly finished for long operational life.Type: High-Back Revolving Chair with Adjustable Height and WheelsComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
459	Providing and supplying Cafeteria Chair (Any Other Shape) with Armrest, made of ergonomically designed seat and back moulded from virgin polypropylene (PP) / high-grade plastic of approved colour and shape, supported on powder-coated mild steel / chrome-plated tubular frame of adequate thickness for stability and durability.Chair shall have integral / fitted armrests, smooth edges, and non-slip nylon glides at leg ends.The chair shall be lightweight, stackable, corrosion-resistant, easy to clean, and suitable for cafeteria / multipurpose seating use.All welds and joints shall be ground smooth and finished uniformly.Type: Cafeteria Chair – Any Other Shape with ArmrestComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
460	Providing and supplying INTEGRITY SQUARE Cafeteria Chair with Armrest, having an ergonomically contoured seat and back made of injection-moulded virgin polypropylene (PP) / high-grade plastic of approved colour and finish, supported on a sturdy powder-coated / chrome-plated tubular steel frame of suitable gauge.The chair shall be fitted with integrated or fixed armrests, anti-skid nylon leg caps, and all welds shall be smoothly ground and rust-protected.The unit shall be lightweight, stackable, durable, corrosion-resistant, and easy to maintain, suitable for cafeteria, canteen, or public seating applications.Type: Cafeteria Chair with ArmrestComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
461	Providing and supplying Unbranded Wooden Modern Dining Table, made from seasoned and chemically treated hardwood / engineered wood (MDF / particle board / plywood) with laminated or melamine-polished surface finish of approved shade and texture.The table shall be of modern design, sturdy construction, and smooth edges, supported on solid wood / metal legs with anti-skid buffers.All joints shall be glued and screwed, surfaces smoothly finished and sealed, and materials shall conform to relevant IS standards for furniture manufacture.The table shall be durable, termite-resistant, and easy to maintain.Make: Unbranded (as approved by Engineer-in-Charge)Type: Wooden Modern Dining TableComplete in all respects as per specifications and directions of Engineer-in-Charge.
462	Providing and supplying Door Curtains, made from premium woven fabric (minimum 260 GSM) in off-white colour, manufactured using high-quality yarn on handloom / powerloom, ensuring uniform texture, smooth finish, and colour fastness.Curtains shall be stitched with interlocked seams, hemmed edges, and fitted with eyelets or curtain tape as required for hanging.Fabric shall conform to IS:13717/1993 (Curtain and Upholstery Fabric – Cotton/Blended) standards.The material shall be washable, shrink-resistant, fade-resistant, and suitable for long-term institutional use.Type: Door Curtain, 260 GSM, Off-White ColourComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
463	Providing and supplying Floor Standing Display Cabinet, fabricated from seasoned hardwood or high-quality engineered wood (MDF / particle board / plywood) of approved make and finish.Cabinet to have fully glazed doors made with 5 mm thick clear float glass fitted in wooden / engineered wood frame, with concealed hinges, magnetic catch, and lockable handle arrangement.The internal structure shall include adjustable shelves, polished / laminated on all visible surfaces with scratch- and stain-resistant finish of approved shade.The base shall be sturdy with level-adjustable legs or skirting for floor stability.All edges to be smoothly finished, and hardware (hinges, handles, screws) to be of stainless steel or equivalent corrosion-resistant material.Type: Floor Standing Display Cabinet with Glass in Wood / Engineered Wood Frame DoorComplete in all respects as per approved design, manufacturer’s specifications, and directions of Engineer-in-Charge.
464	Providing and supplying Drawer Type Steel Filing Cabinet, fabricated from prime quality CRCA (Cold Rolled Close Annealed) steel sheets of minimum 0.8 mm thickness for body and 1.0 mm for drawers, duly powder-coated (minimum 50–60 microns) in approved shade.Cabinet to be of standard office design, having multiple pull-out drawers (2/3/4-drawer type as specified) mounted on heavy-duty ball bearing telescopic slides for smooth and noiseless operation.Each drawer shall have a label holder, recessed handle, and central locking system to secure all drawers simultaneously.All edges and corners shall be rounded and free from burrs, and the unit shall rest on adjustable levelling glides.The cabinet shall be durable, rust-resistant, and suitable for foolscap / A4-size file storage.Material Finish: Powder-coated steel in grey / beige / approved colour.Type: Drawer Type Steel Filing CabinetComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
465	Providing and supplying Mid-Back Chair with Fixed Armrest (without cushion and padding), made of ergonomically designed one-piece moulded seat and back from virgin polypropylene (PP) / high-quality plastic of approved colour and finish.The chair shall have integrated fixed armrests, supported on a strong powder-coated / chrome-plated tubular steel frame of adequate gauge for rigidity and stability.The surface shall be smooth, easy to clean, non-fading, and resistant to moisture and corrosion.All joints and welds shall be neatly finished and burr-free, with anti-skid nylon / rubber shoes on legs.The chair shall be lightweight, durable, and suitable for institutional / office / cafeteria use.Type: Mid-Back Chair with Fixed Armrest (without Cushion & Padding)Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
466	Providing and supplying Low-Back Chair with Fixed Armrest and Padding, constructed with an ergonomically designed low-back frame made of tubular steel / metal section of suitable gauge, fitted with fixed armrests of polypropylene or PU material.Seat and back to be upholstered with high-density foam padding (minimum 32D for seat, 28D for back) and covered with fabric / leatherette upholstery of approved colour and shade.The chair shall have a rigid welded structure, anti-skid leg caps, and smooth, durable finish with powder coating (minimum 50 microns).All joints shall be strong, burr-free, and neatly finished.The chair shall be comfortable, sturdy, and suitable for office / institutional / visitor seating.Type: Low-Back Chair with Fixed Armrest and PaddingComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
467	Providing and supplying Unbranded Wooden Modern Bed, fabricated from seasoned and chemically treated hardwood / high-quality engineered wood (MDF / particle board / plywood) of approved make and finish.The bed shall be of modern design, complete with headboard and footboard, sturdy frame construction with smooth edges and securely joined corners.The top structure shall support the mattress on solid wooden slats or flat board base, finished with laminated / melamine-polished / PU-coated surface of approved shade.All joints to be screwed and glued, free from sharp edges or warping.The bed shall be termite-resistant, durable, and easy to maintain, suitable for institutional or domestic use.Make: Unbranded (as approved by Engineer-in-Charge)Type: Wooden Modern BedComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
468	Providing and supplying Single Wooden Bed with Headboard and Footboard, made from seasoned and chemically treated hardwood / high-quality engineered wood (plywood / MDF / particle board) of approved make and finish.The bed shall have a sturdy frame structure with smoothly finished headboard and footboard, all edges rounded and joints glued and screwed for rigidity.Top to have wooden slats or flat board base suitable for mattress placement.Visible surfaces to be laminated / melamine-polished / PU-coated in approved shade and texture.All components shall be termite-resistant, durable, and free from warping or sharp edges.The bed shall be of standard single size (approx. 900 mm × 2000 mm × 450 mm height) or as approved by Engineer-in-Charge.Type: Single Wooden Bed with Headboard and FootboardComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
469	Providing and supplying Dressing Table with Cupboard and Open Shelves, made from seasoned hardwood / high-quality engineered wood (plywood / MDF / particle board) of approved make and finish.The unit shall consist of a mirror panel (minimum size 1200 mm × 450 mm) mounted on a sturdy wooden frame, integrated with a storage cupboard with hinged door(s) and open display shelves for utility items.All visible surfaces shall be laminated / melamine-polished / PU-coated in approved shade and texture.Edges shall be rounded and smoothly finished, and hinges, handles, and fittings shall be of stainless steel or other corrosion-resistant hardware.All joints shall be strongly fixed, neatly finished, and free from burrs or sharp edges.The dressing table shall be durable, termite-resistant, and aesthetically designed for residential or institutional use.Type: Dressing Table with Cupboard and Open ShelvesComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.
470	Bill No. XVIII: Electrical Works
471	EXTERNAL ELECTRICAL WORKSSupplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required3.5 core 50 Sq mm
472	3.5 core 95 Sq mm
473	3.5 core 120 Sq mm
474	4 core 10 Sq mm
475	4 core 16 Sq mm
476	4 core 25 Sq mm
477	3.5 core 185 Sq mm
478	3.5 core 240 Sq mm
479	Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -10 sqmm
480	16 sq mm
481	25 sq mm
482	50 sq mm
483	95 sq mm
484	185 sq mm
485	240 sq mm
486	Supplying and fixing of heat shrinkable straight through cable jointing kits of following sizes : -2 core 16 sqmm or 4 core 10/16 sq mm size
487	3.5 core or 4 core 25/35 sq mm size
488	3.5 core or 4 core 50 sq mm size
489	3.5 core or 4 core 95 sq mm size
490	3.5 core or 4 core 120/150 sq mm size:-
491	3.5 core or 4 core 185 sq mm size:-
492	3.5 core or 4 core 240 sq mm size:-
493	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)
494	160 mm dia (OD-160 mm & ID-135 mm nominal)
495	LT Panel :-Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and 900mm (NS) deep made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required for completeness and as per attached specification, direction of Engineer, CPWD standards and Electrical Inspectorate standards. (Only face area is to be measured)INCOMER1 No.600A FP MCCB(35 KA) (1 for main incomer)4 pole MCCB, 600A, Adjustable Microprocessor Release, 35KA for D.G incomer - 1nosMetering & Indication2 set of phase indicating lamps2 set of (0-500V) Voltmeter with VSS1 set of (0-160A) Ammeter with ASS with 3 no s.160/5A CTs1 set of (0-200A) Ammeter with ASS with 3 no s.200/5A CTsBUS-BAR 1 Set of 1000A TPN Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 10 Nos.63 A FP MCCB (10KA)
496	Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum sub main distribution board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as following:. 4 pole MCCB, 160A, 35KA (1no.)as incomer analog type 0-100 amp ammeter of size 100x100 (NS)analog type 0-500 amp voltmeter of size 100x100 (NS)selector switch for voltmeterselector switch for ammetermeter230 volt LED type indicating lamp (3nos.)63A-TP (MCB) (6 no.), 32A-TP (MCB) (4),32A-DP (MCB) (4)for out going as outgoing
497	Design, Fabrication, Supply, Erection, Testing and commisioning of Powder coated, Weather Proof Double door type Feeder pillar fabricated out of 14 guage CRCA sheet steel in cubical, free standing, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Feeder pillar shall be treated with all anti-corrosive process before painting as per specification. Feeder Pillar shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels. Approval shall be taken for each panel before fabrication.direction of Engineer, CPWD standards and Electrical Inspectorate standards. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)- Feeder Pillar:.INCOMER- 1No. 63A FP MCCB(35 KA) , 1No. 63A FP Contactor, AOM switch & Timers for 24 Hrs. settingMetering & Indication- 1 set of phase indicating lampsBUS-BAR- 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.OUTGOINGS-4 Nos. 32A FP MCB and 15 Nos. 6-32 SP MCB
498	Supplying, installation, testing and commissioning of following capacity diesel Generating Set (alternator directly coupled to diesel engine) compete in all respect broadly comprising of following and as per CPCB 2 norms (upto date ammended), including following specification. A. Alternator : Self excited, brush less type, of following capacity, 3 phase, 415 volts 50 Hz, 4 pole, AC alternator complete with all accessories.B. Engine : water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2 metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification.C. AMF Panel Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches, meters and other accessories, internal wiring, connection, inter-connection etc. for trouble free smooth functioning of DG Set complete with battery charger and leads as per specification.D. Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as per specification.250 KVA
499	Supply, Installation, Testing and Commissioning of Distribution Transformer (3ISLevel- ll)-DTR 250KVA 11/0.433KV as per TSECL Standards and Specification and providing all necessary connections as per the instructions of Engineer-in-charge.
500	INTERNAL ELECTRICAL WORKSWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.Group A

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tripura Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Redevelopment Of Saima Lodge At Gandacherra, Dhalai-Tripura

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Redevelopment Of Saima Lodge At Gandacherra, Dhalai-Tripura

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us