|
| 1 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. \\"M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).\\" |
| 2 | Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. Hot finished seamless type tubes. |
| 3 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 0.63 mm thick with zinc coating not less than 275 gm/m2 |
| 4 | a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart) |
| 5 | S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: 200mm dia |
| 6 | S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 7 | Providing & lowering of G.I. Pipes, flange pipe including rubber washer and nuts of 8 mm dia complete in all respect I.S.1239 Marked. B Class 50 mm dia |
| 8 | P & F Full way Valve (IS: 778 Mark) or wheel valve of approved make Gun metal 50mm nominal bore) |
| 9 | Earth work in excavation over area ( exceeding 30 cm in depth. 1.5 Mtr in width as well as 10 sqm on plan) including disposal of excavated earth lead up to 50 m and lift up to 1.5 Mtr. Disposal earth to be leveled and neatly dressed.All kinds of soil |
| 10 | Providing and fixing anodized aluminium work (Anodizing to be got done from approved Anodizer) for doors, windows ventilators and partition with extruded built up standard tubular and other sections of approved make conforming to IS : 733 and IS 1285 anodised transparent and dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15), fixed with rowel plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth rust free straight, mitred and jointed mechaincally wherever required including cleat angle Aluminium snap beading for glazing /panelling , C.P. brass/ stainless steel screws, AI. Tower bolt & AI handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separtely). For fixed portions |
| 11 | For shutters of openable doors, windows & ventilators including providing & fixing hinges / rollers etc. and making provisiion for fixing of fittings wherver required (lockes shall be paid for separately). |
| 12 | Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade) particle board grade I type IInd conforming to IS: 12823 bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in aluminium doors windows shutters and partitions frame with C.P. Brass /stainless- steel screws etc. complete as per Architectural drawing and direction of Engineer in charge. Pre laminated particle board with decorative lamination on both side |
| 13 | Supply & Planting of shady plants ( Neem. Peepal, Goolar, Jamun, Imli or other specified) along road side including the following activities:-1. Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage.2. Supply of plant at site of two years of age & height more than 1.50 Mtr.3. Supply of dry manure(Farm yard manure organic)4. Supply of Insecticides.5. Digging of pits size 60x60x60 cms. Including removal of stones. Manuring application of insecticides & watering at least 1.5 Liter per plant after planting6. Half brick Circular tree guard in second class bricks, internal dia 1.25 meter and height 1.20 meter above ground and 0.20 meter above ground and 0.20 meterr below ground. Bottom two courses laid dry and top three couses in cement mortar 1:6 ( 1 Cement : 6 Sand) and the intermediate courseses being in dry honey comb masonry. As per design complete.7. Watering to plants8. Maintance of plants by the contractor including pits, preparation of Thavala Hoeing weeding etc & application of insecticiedes etc. & security. If the plant die during maintence contractor has to replace same heingh plant at his own cost. |
| 14 | Supply & Panting of ornamental plants ( Kachnar, Amaltas, Gulmohar, Arjun, Kala, Siris, Jacranda etc. or other specified) along road side including the following activities :-1. Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage 2. Supply of plant at site of two years of age & height more than 1.50 Mtr. 3. Supply of dry manure( Farm yard manure organic) 4. Supply of Insecticides5. Digging of pits size 60x60x60 cms. Including removal of stones. Manuring application of insecticides & watering at least 1.5 liter per plant after planting. 6. Half brick Circular tree guard in second class bricks. Internal dia 1.25 meter and height 1.20 meter above ground and 0.20 meter below ground. Bottom two courses laid dry and top three courses in cement morter 1:6(1 Cement : 6 Sand) and the intermediate courses being in dry honey comb masonry. As per design complete.7. Waterring to Plants. 8. Maintenance of plants by the contractor including pits. Preparation of Thavala Hoeing weeding etc. & application of insecticides etc. & security. If the plant die during maintencance contractor has to replace same height plant at his own cost. |
| 15 | P & F Pilllar Cocks (IS :8934 Mark) of superior quality andapproved make:C.P. Pillar cock, 15 mm dia nominal bore |
| 16 | P & F Bib Cock (IS : 8931 Mark), Superior quality ofapproved make: Brass 400 grm,15mm nominal bore. |
| 17 | P & F Inlet Connection (Angle Valves) Superior quality, ofapproved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked) |
| 18 | P & F Full-way Valve (IS:778 Mark) or wheel valve ofapproved make : Gun-metal 25mm nominal bore. |
| 19 | P & F 15 mm. Dia Connection Pipe of approvedquality/make : PVC pipe with C.P. Brass nuts upto length, 300mm |
| 20 | P & F Gun-metal Non-return Valve or Check Valve (IS:Make) of approved make, superior quality:25 mm nominal bore.Horizontal |
| 21 | CPVC Plumbing Pipe For Hot & Cold ISI SDR-11 20 mm |
| 22 | CPVC Plumbing Pipe Fitting Elbow 20 mm |
| 23 | Coupler20 mm |
| 24 | Tee20 mm |
| 25 | Union20 mm |
| 26 | Reduce Coupler25 mm - 20 mm |
| 27 | Reducing Tee25 mm - 20 mm |
| 28 | CPVC Ball Valve20 mm |
| 29 | CPVC BR Elbow20 mm x 15 mm |
| 30 | CPVC BR Tee20 mm x 15 mm |
| 31 | CPVC BR MTA20 mm x 15 mm |
| 32 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.)approved quality /make including joining the pipe with solventcement rubber ring and lubricant. |
| 33 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approvedquality /make including joining the pipe with solvent cementrubber ring and lubricant Coupler (socket)75mm dia |
| 34 | Reducer 110x75mm110mm |
| 35 | Plain tee75mm |
| 36 | Door tee75mm |
| 37 | Bend 4575mm |
| 38 | Bend 87.575mm |
| 39 | Vent covel75mm |
| 40 | Socket plug75mm |
| 41 | Pipe clip75mm |
| 42 | W.C. connector with ring110 mm dia |
| 43 | Plain floor trap110 mm dia |
| 44 | Multy floor trap110 mm dia |
| 45 | P-trap110 mm dia |
| 46 | Q- trap110 mm dia |
| 47 | S-trap110 mm dia |
| 48 | Gully trap110 mm dia |
| 49 | Providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre length) up to 3m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI barbed wire tied to angle iron all complete as per direction of Engineer In Charge with reinforced barbed tape (R.B.T.)/Spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/metre (Cost of MS angle, CC block shall be paid extra) Please Enable Macros to View BoQ information |
