|
| 1 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified & directed by Engr-in-charge. |
| 2 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but not exc 4 Sqm each complete all as specified & directed by Engr-in-charge. |
| 3 | Taking down shutters of any description n. exc. 1 Sqm each complete all as specified & directed by Engr-in-charge. |
| 4 | Taking down shutters of any description exc 1 sqm and n. exc. 2 Sqm each complete all as specified & directed by Engr-in-charge. |
| 5 | M&L extra over rendering or plastaring for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panals, cornices, skirting, drip moulds and similar work n exc 15 cm in width or girth : including cutting to edges, all mitres and stopped ends etc complete all as specified and directed. |
| 6 | S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube in opening complete all as specified & directed by Engr-in-Charge. |
| 7 | S&F factory made solid PVC Moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face and 2mm plain colour PVC sheet on the back face, supplying and fixingin frame at site as per specification and drawing complete all as specified & directed by Engr-in-Charge. |
| 8 | S&F pressed steel frame for doors with double rebates of size 125 x 60mm made with steel sheet of 1.25mm thickness in and including necessary fixing lugs, hinges lock strike plate including making good disturb surface complete all as specified & directed by Engr-in-charge. |
| 9 | S&F pressed steel frame for doors with single rebates of size 105 x 60mm made with steel sheet of 1.25mm thickness in and including making good disturb surface necessary fixing lugs, hinges lock strike plate complete all as specified & directed by Engr-in-charge. |
| 10 | M&L for providing cement concrete type B0 (1:2:4) 12.5mm graded crushed stone aggregate as in pressed steel door frame (backfill) complete all as specified & directed by Engr-in-charge. |
| 11 | S&F for 35 mm thick 2nd class hard wood plain, framed paneled shutters (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated (factory made shutters) complete all as specified & directed by Engr-in-charge. |
| 12 | S&F for 30 mm thick 2nd class hard wood plain, framed factory made Flush shutters, solid core constructon with block boards core and plywood face panels, commercial type on both sides all complete all as specified & directed by Engr-in-charge. |
| 13 | M&L for factory made 2nd class hardwood (Hollock) glazed & skeleton shutters, 35mm thick open rebated and prepared to receive wire cloth, glass, gauze etc. with edges of framing plain chamfered or rounded, fitted with cut and metred beads ofr securing glass, gauze etc sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a), complete all as specified. NOTE : Wire gauge shutter should also have the provision of vertical member of size 100mm 35mm at middle of the shutter. |
| 14 | S&F in repair Factory made box type steel window / ventilators composite type with double rebated pressed steel frames 80 mm x 60mm (Peripherral) and 80x75mm (Intermediate members) made out of cold rolled 1.25mm thick sheet having steel window/vertilators shutter with sach bar of MS tubular section of size 50mm x 20mm x 1-1mm thick fixed with box type hinges including MS flat as in beading for wire mesh shutter and glass oil putty with glazing pin for glazed shutter, and handle of 100mm size made out of Z section 01 No, MS stove enamelled black towar bolt of size 120mm 02 Nos, 150 mm mild steel hooks and eyes, each sutter flat iron 40mm x 1.25mm and 200mm long hold fasts 04 Nos each window including necessary filling hollow frame with PCC (1:3:6) & also cutting holes for inserting holdfasts, including making good disturbed surfaces to match with existing colour surface and 10mm x 10 mm mild steel solid square bars in 100mm c/c horizontaly as grill fixed to window/ ventilators frame using necessary welding complete all as specified & directed by Engr-in-charge. |
| 15 | S&F in repairs 18/19 mm thick Block board grade II quality interior grade commercial type with out decorative face including supplying & fixing 18 mm wide edge tape of same texture to all exposed edges including necessary frame work for cupboards complete all as specified & directed by Engr-in-charge. |
| 16 | M&L 0.9 mm Decorative lamination type 1 of surface finish, coloured and pattern as approval fixed with approval adhesive as per manufacture instruction all as specified and directed. |
| 17 | S&F continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps when open 30mm fixed in repair complete all as specified & directed by Engr-in-charge. |
| 18 | S&F MS butt hinges medium weight cold rolled mild steel and fixed, size of hinges is 100 mm complete all as specified & directed by Engr-in-charge. |
| 19 | S&F Aluminium anodised barrel tower bolts of extruded section length of bolt is 150mm complete all as specified & directed by Engr-in-charge. |
| 20 | S&F Aluminium anodised barrel tower bolts of extruded section length of bolt is 200mm complete all as specified & directed by Engr-in-charge. |
| 21 | S&F in repair Aluminium anodised barrel tower bolts of extruded section length of bolt is 200mm complete all as specified & directed by Engr-in-charge. |
| 22 | S&F 300 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staples plate and fixed with hasp staple bolt type, fixing clips of sheet, cast or extruded section and fixing bolts complete all as specified & directed by Engr-in-charge. |
| 23 | S&F 125 mm long extruded aluminium alloy, handles, fabricated type, anodized, complete all as specified & directed by Engr-in-charge. |
| 24 | S&F in repairs 125 mm long extruded aluminium alloy, handles, fabricated type, anodized, complete all as specified & directed by Engr-in-charge. |
| 25 | M&L for welding in repairs as required, thickness of metal to be welded exc 6 mm but n. exc. 9mm complete all as specified & directed by Engr-in-charge. |
| 26 | S&F 125 mm size hasp and staple safety type aluminium anodized complete all as specified & directed by Engr-in-charge. |
| 27 | S&F in repair 40 mm dia cupbords knobs fixed with nut screwes and washer of mild steel bright all complete all as specified & directed by Engr-in-charge. |
| 28 | S&F in repair magnetic latches for kitchen cabinet and cupbords all complete all as specified & directed by Engr-in-charge. |
| 29 | Hacking out old broken glass (any thickness) from wooden/steel frames, glazed with putty of fixed with screws complete all as specified & directed by Engr-in-charge. |
| 30 | S&F sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sqm in each pane of thickness 4.0 mm including necessary beeding complete all as specified & directed by Engr-in-charge. |
| 31 | S&F sheet glass ordinary quality and glazing with oil putty in squares exc. 0.5 Sqm in each pane of thickness 4 mm including necessay beeding complete all as specified & directed by Engr-in-charge. |
| 32 | S&F Figured glass, pinhead type and glazing with oil putty in square exc. 0.5 Sqm in each pane of thickness 4.0 mm including necessay beeding complete all as specified & directed by Engr-in-charge. |
| 33 | S&F stainless steel cloth mesh 1.4 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples including necessay beeding complete all as specified & directed by Engr-in-charge. |
| 34 | M&L for applying 2 coats of synthetic enamel paint over steel and iron surfaces of any description, over 10 cm in width or girth including preparation of new or previously treated surface over a coat of red oxide oxide primer complete all as specified and directed by Engr-in-Charge. |
| 35 | M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed by Engr-in-Charge. |
| 36 | S&F in repair 300 mm mild steel ordinary rat tail rod pattern springs, including roller & roller plate complete all as specified directed by Engr-in-charge. |
| 37 | S&F in repair Floor door stopper of Aluminium alloy body anodised with hard drawn steel spring 140mm size fixed in floor complete all as specified directed by Engr-in-charge. |
| 38 | S&F in repair mortice lock, vertical type size 100 mm brass 4 lever in repair complete all as specified and directed by Engr-in-charge. |
| 39 | S&F in repairs of Drapery rod/ curtain rod 25 mm diameter, stainless steel (304 grade) of thickness 20 gauge with standard type socket including brackets, side, doms, wall to wall, finel, rings complete all as specified and directed. |
| 40 | M&L Non skid tiles 7 to 8 mm (Square/Rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match all including screed bed or bedding layer of 15mm thick for laying floor finishes in cement mortar 1:6 and dismantling floor, hearth or wall tilling, cement mortar bedding (but not Backing) removing serviceable tiles to store and rubbish off the premises directed by Engr-in-Charge. |
| 41 | M&L Glazed ceramic colured tiles in vertical surface 450x300 mmx 7 mm thick set and jointed in neat cement slurry and pointed in neat cement slurry and pointed in white or coloured cement to match including backing coat of 10 mm thick in cement mortar 1:4 and dismantling floor, hearth or wall tilling, cement mortar bedding (but not Backing) removing serviceable tiles to store and rubbish off the premises. |
| 42 | M&L for non-skid Ceramic coloured tiles 8-10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in Cement Mortar 1:6 and dismantling of existing tiles, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-charge. |
| 43 | S&F in repair Aluminium powder coated door seal strip with glass wool fixed with steel screws at bottom rail of external door complete all as specified directed by Engr-in-charge. |
| 44 | Taking down cement plaster of any description on brick or stone walls etc, including raking out joints, hacking for key scrubbing down with water, etc. |
| 45 | M&L for rendering cement plaster 15 mm thick in Cement Mortar 1:4 other than fair faces of brick work or concrete surfaces, is to be finished fair & even without using extra cement upto 12m height including necessary scaffolding etc complete all as specified and directed by Engr-in-charge. |
| 46 | M&L for Rough cast plaster After applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly better than normal for rendering to ensure that larger aggregates are thoroughly covered, including taking down cement plaster and racking out joints, hacking for key scrubbing down with water etc, complete all specified and directed by Engr-in-Charge. |
| 47 | M&L for rendering 15 mm thick in CM 1:6 on fair face of brick work or concrete surfaces finished even and smooth without using extra cement including taking down Cement plaster on brick or stone walls, etc and raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified & directed by Engr-in-charge. |
| 48 | M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over one coat of primer and wall care putty 2 mm thick on walls complete all as specified and directed. |
| 49 | M&L for preparation of newly plastered/un treated surface of wall / coloum, beam, chajja etc. and leveling / edgesing the disturbed surface a thin layer of putty and making smooth by using sand paper applying two coat of extrior acylic emulsion (weather proof), to be applied complete all as manufacturer's instruction and as directed. |
| 50 | S&F in repair Mild Steel Framed work as in doors/gates/grills and like of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe-410-W Gde E-250 complete all as specified and as directed by Engineer-in-Charge. |
| 51 | M&L Factory made single extruded WPC (wood polymer composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 45x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk ) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire resisdant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/lugs or SS dash fasteners shall be paid for seperately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 52 | M&L Factory made single extruded WPC (wood polymer composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire resisdant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/lugs or SS dash fasteners shall be paid for seperately). Note : For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 53 | M&L Factory made single extruded WPC (wood polymer composite) solid plain flush shutter of 30 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire resisdant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/lugs or SS dash fasteners shall be paid for seperately). |
| 54 | M&L Factory made single extruded WPC (wood polymer composite) solid plain flush shutter of 35 mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire resisdant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/lugs or SS dash fasteners shall be paid for seperately). |
| 55 | Material and labour for powder coated aluminium (minimum thickness of polyester powder coating 50 micron) work for fixed frame portion and shutters of doors, sliding door (any track), openable/sliding windows, ventilators, partitions sliding/openable with extruded built up standard tubular section/appropriate Z section and other section conforming to IS : 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/neoprene gasket roller etc aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/gauged/paneling, CP brass/stainless steel screws, complete all as specified and directed. |
| 56 | M&L Machine cut kota stone slab flooring 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 20 mm thick Screed bed or bedding layer in Cement Mortar 1:6 for laying floor finishes etc and dismantling old kota stone and rubbish off the premises complete all as specified and as directed etc |
| 57 | M&L Polished granite stone slab 18- 20mm thick coloured as in cooking platform/door sills, partitions, jambs, pillars, window-cills, set in 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) and jointed with grey cement slurry and pointed in neat white cement slurry mixed with pigment to match the shade of floors, including moulding at front edge or both edges including dismantling existing granite and rubbish off the premises complete all as specified and as directed by Engr-in-Charge. |
| 58 | Supply and fixing in repair of UPVC windows three track, sliding type in any position with 6mm thick toughened glass of approved make (glass tint as approved by GE) with chowkhat including all necessary fittings and fixtures complete all as directed and specifed by Engr-in-Charge. |
| 59 | M&L for applying one coat of oil bound distemper on wall, white or tinted, including prepration of old surface complete all as specified and directed by Engr-in-Charge. |
| 60 | M&L for applying one coat of oil bound distemper on ceiling, white including prepration of old surface complete all as specified and directed by Engr-in-Charge |
| 61 | M&L for complete removal of existing surfaces of wall applying 2 to 3 mm thick (average thickness) wall care putty on prepared surfaces of walls, applying two coat of oil bound distemper of white or tinted over a coat of primer as per the manufacture instructions complete all as specified and directed by Engr-in-Charge. |
| 62 | M&L for preparation of old steel surfaces and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge. |
| 63 | M&L preparation of old wooden surfaces and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge. |
| 64 | Note :- Amount of credit of Rs. 35500.00 for retrieved materials is mentioned in Schedule of Credit of tender documents in pdf form which will be deducted offline while acceptance of tender. Please Enable Macros to View BoQ information |
